Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 10 of 10
Search took 0.02 seconds.
Search: Posts Made By: Golfdad75
Forum: General Maintenance 01-11-2024, 10:06 PM
Replies: 18
Views: 794
Posted By hanleyclifford
Odds are good that one or more of those studs...

Odds are good that one or more of those studs will come out of the block. If that happens check the threads and if there is any question replace the studs and set the new ones with thick Permatex....
Forum: Aftermarket Kits and Accessories 01-08-2023, 06:14 PM
Replies: 6
Views: 2,980
Posted By msmith10
I don't know what tubing is connected to your oil...

I don't know what tubing is connected to your oil removal pump, but in general, Moyer's oil change kit comes with barbed fittings to connect the drain tubing with your pump tubing, and a cap to cap...
Forum: Cooling System 08-02-2022, 08:36 AM
Replies: 13
Views: 2,669
Posted By ndutton
I've attached one of the worksheets we used...

I've attached one of the worksheets we used during the testing of the Moyer Marine thermostat showing all the temperature measurement locations.
Forum: Cooling System 07-28-2022, 07:55 PM
Replies: 13
Views: 2,669
Posted By Al Schober
Those old Oberdorfer 202 pumps DO wear out. I...

Those old Oberdorfer 202 pumps DO wear out. I fought with one for years - new shaft, new seals, etc. I figure time working on the pump is time I could spend sailing. Get the new Moyer pump and...
Forum: Cooling System 07-28-2022, 01:27 PM
Replies: 13
Views: 2,669
Posted By sastanley
The biggest issue is it won't prime/pump anymore....

The biggest issue is it won't prime/pump anymore. If you need to replace, I highly recommend the Moyer 502 pump..it moves way more water than my 202m3 did.

Throw up a picture, someone here can...
Forum: Cooling System 07-28-2022, 09:43 AM
Replies: 13
Views: 2,669
Posted By ndutton
Depending on cavity wear, it may not be...

Depending on cavity wear, it may not be rebuildable. Sure, bearings, seals and shaft are all replaceable but if the cavity in which the impeller spins is worn to a point where there is no longer a...
Forum: Electrical 04-06-2021, 10:18 AM
Replies: 7
Views: 2,175
Posted By roadnsky
Connect a jumper wire (12-14 gauge) between the...

Connect a jumper wire (12-14 gauge) between the large battery terminal on the starter solenoid and the positive terminal (+) of the coil.
Connecting this jumper wire is the same as turning on the...
Forum: Introductions 11-27-2020, 11:21 AM
Replies: 11
Views: 14,867
Posted By roadnsky
Yes, just aft of the carb. See the attached...

Yes, just aft of the carb.
See the attached pics...
Forum: Ignition System 06-02-2016, 12:09 AM
Replies: 9
Views: 3,524
Posted By ndutton
I expect you may have a blown inline fuse, a...

I expect you may have a blown inline fuse, a damaged ignition switch or maybe the wire itself has parted (fused) as a result of the shorted lead. Sometimes the conductor will part inside the...
Forum: Electrical 09-09-2015, 10:31 AM
Replies: 32
Views: 13,964
Posted By ndutton
Golfdad, to answer your question directly, this...

Golfdad, to answer your question directly, this is from Magnecor:
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 01:58 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved