Forum: Troubleshooting
12-28-2023, 06:45 PM
|
Replies: 28
Views: 7,236
Seems to me the problem could be that your not...
Seems to me the problem could be that your not getting enough water through to the engine when the rev's are up and under load. I would begin by simplifying the set up you have between the through...
|
Forum: Exhaust System
08-28-2023, 07:34 PM
|
Replies: 20
Views: 4,272
|
Forum: Troubleshooting
08-22-2023, 04:19 PM
|
Replies: 35
Views: 3,869
|
Forum: Troubleshooting
07-09-2023, 03:41 PM
|
Replies: 4
Views: 754
|
Forum: Troubleshooting
07-07-2023, 02:57 PM
|
Replies: 5
Views: 689
|
Forum: Cooling System
03-13-2023, 08:11 PM
|
Replies: 7
Views: 1,683
|
Forum: Cooling System
01-01-2023, 12:20 AM
|
Replies: 29
Views: 4,312
Re the overheating problem. The first thing I...
Re the overheating problem. The first thing I would do is check the through hull valve to see that it is not plugged. Disconnect the intake hose from the through hull valve and then open it up. You...
|
Forum: Troubleshooting
09-20-2022, 11:28 PM
|
Replies: 12
Views: 2,145
It seems to me that you're pump could be just...
It seems to me that you're pump could be just sucking air. You might just need to prime your strainer by making sure it's full and making sure the seal is tight. I've had your situation in the past...
|
Forum: Troubleshooting
07-19-2022, 12:36 AM
|
Replies: 13
Views: 2,008
I recalled and meant to add that yesterday...
I recalled and meant to add that yesterday removing the basket filter top was significantly more difficult than normal. It (filter) was completely empty of water and felt as if under strong vacuum...
|
Forum: Troubleshooting
11-20-2021, 11:29 PM
|
Replies: 18
Views: 2,609
|
Forum: Fuel System
11-29-2018, 10:51 PM
|
Replies: 27
Views: 9,082
|
Forum: Cooling System
06-18-2017, 01:35 AM
|
Replies: 10
Views: 3,895
Try removing the fitting at the aft end of the...
Try removing the fitting at the aft end of the manifold where the water exits the manifold and see if it's clogged. Some crud might have dislodged when the engine overheated because of lack of flow....
|
Forum: General Interest
08-06-2016, 08:17 PM
|
Replies: 20
Views: 5,105
|
Forum: Drive Train / Propellers
07-08-2016, 06:38 PM
|
Replies: 13
Views: 9,991
|
Forum: Drive Train / Propellers
06-23-2016, 07:00 PM
|
Replies: 9
Views: 6,509
|
Forum: Cooling System
06-08-2016, 08:07 PM
|
Replies: 23
Views: 9,127
Ok, so before you take the side plate off try...
Ok, so before you take the side plate off try disconnecting that hose between the thermostat housing and the manifold and crank her over. If no water exits the thermostat housing then the blockage...
|
Forum: Cooling System
06-08-2016, 12:52 AM
|
Replies: 23
Views: 9,127
Re-read post #2 and check to see if the fitting...
Re-read post #2 and check to see if the fitting is plugged. Remove it from the manifold for a proper examination. It's a known location for Krap buildup if you're raw water cooled and it's easy to...
|
Forum: Cooling System
05-31-2016, 11:47 PM
|
Replies: 26
Views: 12,967
FWIW. I've done a ton of work using various...
FWIW. I've done a ton of work using various sanding equipment and I wouldn't even think about trying this job with a "buzzy" as Shawn calls them. You would need to be blessed with a miricle for it...
|
Forum: Introductions
10-28-2015, 08:02 PM
|
Replies: 36
Views: 21,832
|
Forum: Troubleshooting
08-07-2015, 12:36 AM
|
Replies: 2
Views: 2,686
Brad,
I couldn't clearly pick out the rattle...
Brad,
I couldn't clearly pick out the rattle on the video but I'm deafer than a post anyway (kind of a blessing sometimes) but just to eliminate the possibility of the rattle coming from the...
|