Return to the home page...
Moyer Marine Atomic 4 Community - Home of the Afourians
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
FAQ
Members List
Search
Today's Posts
Mark Forums Read
Showing results 1 to 10 of 10
Search took
0.01
seconds.
Search:
Posts Made By:
Ball Racing
Forum:
Overhaul
03-27-2020, 05:41 PM
Replies:
7
Fretting over lifters, replace or not?
Views:
2,531
Posted By
Ball Racing
My cam and lifters had rust damage from a...
My cam and lifters had rust damage from a hurricane flood into a garage where the freshly rebuilt motor was on the floor.
Anyway, I took each lifter and hand lapped it on a diamond stone.
They have...
Forum:
Polls
03-18-2020, 08:45 PM
Replies:
21
Poll:
Stacking Gaskets...Do any of you do it?
Views:
9,599
Posted By
Ball Racing
not a displacement hull comparison
As to rpms and head gaskets:
I am only using one head gasket, and last outing turning 3600rpm direct drive.
In my tuning process in my planning hull, I got an increase in rpms with headgasket...
Forum:
General Interest
02-22-2020, 07:34 PM
Replies:
154
12.5 mph
Views:
75,194
Posted By
Ball Racing
They are neat, and very few remain.
They are neat, and very few remain.
Forum:
General Interest
02-22-2020, 07:00 PM
Replies:
154
12.5 mph
Views:
75,194
Posted By
Ball Racing
Kinda thinking of building a light version of...
Kinda thinking of building a light version of this boat,
just to see how much more speed I can get from it.
Or build a Maryland "dovetail" or also called draketail to put the atomic in.
Long and...
Forum:
General Interest
10-23-2014, 03:13 PM
Replies:
154
12.5 mph
Views:
75,194
Posted By
Ball Racing
Heres what 3,500+ RPMS sound like. You...
Heres what 3,500+ RPMS sound like.
You shouldn't have to be on facebook to view it....
Forum:
Fuel System
12-20-2012, 04:54 PM
Replies:
154
PCV VALVE... Really?
Views:
53,192
Posted By
Ball Racing
Not so on FORD late 60's
Basically in 1967-68 Ford installed emission devices. On a automatic trans car had a PCV valve and a manual trans car had a thermactor smog pump.
The vacuum source was a plate under the carb or off...
Forum:
Troubleshooting
09-15-2012, 08:04 PM
Replies:
39
Getting Desparate, No Power Past Half Throttle
Views:
24,374
Posted By
Ball Racing
I am not sure how much rpm you used to gain "past...
I am not sure how much rpm you used to gain "past half throttle on the lever"
But with the wheel I first had, there was no use to use more than half throttle because the engine simply did not make...
Forum:
Troubleshooting
06-17-2012, 09:13 AM
Replies:
18
Blow-by Oily Smoke
Views:
12,538
Posted By
Ball Racing
If a "rebuilt" engine needs 10 - 50 hours to stop...
If a "rebuilt" engine needs 10 - 50 hours to stop pumping smoke out the base,
something was not corrected during the rebuild.
The cylinder walls must have been out of round really bad, or there...
Forum:
Exhaust System
03-26-2012, 07:24 AM
Replies:
74
Poll:
Exhaust system size
Views:
46,939
Posted By
Ball Racing
I really don't see needing a large exhaust exit...
I really don't see needing a large exhaust exit from the manifold as of yet.
a 2,000 max rpm average rate engine that is only making upwards of teens of HP at that point, and is 6 to 1 compression...
Forum:
Drawings and Schematics
11-29-2011, 10:41 AM
Replies:
42
Electronic Ignition
Views:
46,350
Posted By
Ball Racing
If you have a resistor on the negative side, then...
If you have a resistor on the negative side, then you don't have to worry as much about mounting location, and about something laying against it and shorting it, as it's already on the ground side?
Showing results 1 to 10 of 10
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Announcements
Introductions
Drawings and Schematics
Testing Protocols
Discussion Topics
General Interest
Polls
Helpful Videos
ABYC and USCG Standards
Troubleshooting
General Maintenance
Ignition System
Electrical
Fuel System
Cooling System
Reversing Gear
Exhaust System
Drive Train / Propellers
Overhaul
Safety
Aftermarket Kits and Accessories
Specialty Tools
Moyer Marine Pin-Up's
Good Guys
Links of Particular Interest
The Wish List
Owner Discussion Groups
Discussion Groups
Alberg
Bristol
C&C
Cal
Catalina
Columbia
Dyer Glamour Girl
Ericson
Grampian
Herreshoff
Irwin
Islander
Morgan
Newport
O'Day
Pearson
Ranger
Sabre
Tartan
Off-Topic
General Discussion (Off-Topic)
Boat Construction/Repair
Captain's Confession
Weather
Marine Electronics / Interfacing and Integration
iPad/Tablet/Laptop Applications on the Water
Classified Ads
For Sale - Engines and Engine Parts
For Sale - Other Items
Wanted to Buy - Engines and Engine Parts
Wanted to Buy - Other items
Tools wanted or offered to rent
All times are GMT -4. The time now is
08:24 PM
.
Moyer Marine Inc.
-
Archive
-
Top
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Universal® is a registered trademark of Westerbeke Corporation
Copyright © 2004-2024 Moyer Marine Inc.
All Rights Reserved