Forum: Exhaust System
06-07-2022, 04:38 PM
|
Replies: 7
Views: 1,671
Mine is a combination of bronze fittings, brass...
Mine is a combination of bronze fittings, brass pipe, steel pipe and steel fittings. The joints are sealed with a high temp sealant from Permatex. The brass and bronze I got from WM, the black steel...
|
Forum: Troubleshooting
12-15-2021, 04:21 PM
|
Replies: 23
Views: 3,214
|
Forum: Introductions
08-12-2021, 03:32 PM
|
Replies: 7
Views: 3,539
|
Forum: Overhaul
11-11-2020, 08:18 AM
|
Replies: 34
Views: 6,875
I used the Permatex AV on the studs when I...
I used the Permatex AV on the studs when I rebuilt my engine, six of them leaked badly. I had to remove the head and studs, clean off all the Permatex, and re installed the studs with Permatex red...
|
Forum: General Interest
11-09-2019, 08:40 PM
|
Replies: 3
Views: 2,266
|
Forum: Troubleshooting
06-17-2019, 03:09 PM
|
Replies: 11
Views: 6,283
|
Forum: General Interest
06-05-2019, 11:38 AM
|
Replies: 8
Views: 4,012
Thanks Al. I thought about having an aluminum...
Thanks Al. I thought about having an aluminum step built but I couldn't find anyone to do it other than a local machine shop. Also, an aluminum step wouldn't completely solve the problem. The step is...
|
Forum: General Interest
06-04-2019, 04:32 PM
|
Replies: 8
Views: 4,012
New Mast Step
I had a steel step for my aluminum mast and both were heavily corroded. So last year I started the repair. I built a new mast step from G10 fiberglass and the mast was re stepped this morning. The...
|
Forum: Introductions
02-16-2019, 02:39 PM
|
Replies: 7
Views: 4,392
|
Forum: Overhaul
08-17-2018, 03:39 PM
|
Replies: 8
Views: 5,322
|
Forum: Troubleshooting
11-09-2017, 12:34 PM
|
Replies: 4
Views: 2,581
There are three oil galley plugs inside the...
There are three oil galley plugs inside the engine. One is behind the camshaft gear, one is under the oil pressure regulator and one s behind the flywheel. Here are pictures of the plugs. The...
|
Forum: Troubleshooting
08-14-2017, 12:11 PM
|
Replies: 13
Views: 6,107
|
Forum: General Interest
07-27-2017, 08:40 PM
|
Replies: 17
Views: 4,413
|
Forum: General Interest
07-27-2017, 05:11 PM
|
Replies: 17
Views: 4,413
|
Forum: General Interest
07-20-2017, 08:28 PM
|
Replies: 36
Views: 8,071
|
Forum: General Maintenance
07-09-2017, 04:35 PM
|
Replies: 3
Views: 2,341
|
Forum: Pearson
07-01-2017, 10:51 AM
|
Replies: 60
Views: 27,963
Here are all the parts I used for my raw water...
Here are all the parts I used for my raw water inlet. The valve, thru hull and tail piece are all 1/2 inch NPS. The strainer is optional, there are differing opinions on the need for the strainer on...
|
Forum: Troubleshooting
07-01-2017, 10:31 AM
|
Replies: 27
Views: 11,680
|
Forum: Drawings and Schematics
06-08-2017, 06:23 AM
|
Replies: 2
Views: 5,594
|
Forum: Exhaust System
06-07-2017, 07:15 AM
|
Replies: 35
Views: 11,195
|
Forum: Exhaust System
06-07-2017, 07:11 AM
|
Replies: 35
Views: 11,195
|
Forum: Exhaust System
04-21-2017, 04:22 PM
|
Replies: 33
Views: 12,372
|
Forum: Drive Train / Propellers
02-05-2017, 08:46 AM
|
Replies: 4
Views: 4,300
|
Forum: Fuel System
01-03-2017, 06:11 PM
|
Replies: 40
Views: 15,706
|
Forum: Fuel System
01-03-2017, 04:42 PM
|
Replies: 40
Views: 15,706
|