Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: dplidr@gmail.com
Forum: For Sale - Engines and Engine Parts 03-30-2021, 02:05 PM
Replies: 20
Views: 6,133
Posted By ronstory
To both of you, price improves with more good...

To both of you, price improves with more good news/information. History of the motor of RWC vs FWC and where it was ran if RWC is good info. IMO, having compression numbers, a video showing it...
Forum: Overhaul 03-02-2021, 01:08 PM
Replies: 4
Views: 2,751
Posted By W2ET
Dave: Is this it (261009)? ...

Dave:

Is this it (261009)?

https://discountmarinesource.com/store/image/cache/data/productsdms/westerbeke/261009-200x200.jpg

If yes, click here...
Forum: Overhaul 02-11-2021, 01:13 PM
Replies: 16
Views: 3,734
Posted By ronstory
Hmmm... if your pistons are 0.005-6" over near...

Hmmm... if your pistons are 0.005-6" over near the top, you are on very edge of acceptable.

My thoughts are if you are just using the motor of limited use to get to/from the dock and a bit of...
Forum: Overhaul 01-27-2021, 09:30 PM
Replies: 7
Views: 3,151
Posted By ronstory
Yes, just get the crank and the cam aligned per...

Yes, just get the crank and the cam aligned per Jack's awesome picture. You will be turning the engine anyways to adjust the lash on the valves so don't worry about setting the disti now.

In my...
Forum: Overhaul 01-27-2021, 05:02 PM
Replies: 7
Views: 3,151
Posted By jcwright
I see this note from Don (from an earlier thread)...

I see this note from Don (from an earlier thread) in my rebuild notes; I think it is relevant to your question:

"The short answer to your question is that the alignment of the timing marks during...
Forum: Overhaul 01-27-2021, 12:25 PM
Replies: 7
Views: 3,151
Posted By jcwright
Hello dplidr. Here is a comment from Don...

Hello dplidr.

Here is a comment from Don Moyer from a related earlier thread:

"There is a small "0" on the front face of one of the teeth of the small crankshaft gear and a small "0" between...
Forum: Troubleshooting 09-18-2020, 06:19 PM
Replies: 9
Views: 10,763
Posted By Don Moyer
Valve spring material

Dave,

We questioned the manufacturer many years ago on this point, and they told us that it's normal for their stainless valve springs to have a bit of magnetic attraction. In all the years we've...
Forum: Overhaul 09-14-2020, 03:54 PM
Replies: 7
Views: 3,179
Posted By Surcouf
been there done that... see post 67,70 and 72. Of...

been there done that... see post 67,70 and 72. Of course I was doing that with the head removed...

https://www.moyermarineforum.com/forums/showthread.php?t=11241&page=3
Forum: Overhaul 09-14-2020, 01:47 PM
Replies: 7
Views: 3,179
Posted By Al Schober
Nope, sounds like a reasonable next step. I've...

Nope, sounds like a reasonable next step. I've done similar, but a think I used a pair of wooden wedges between the lower seat and the tappet.
Make sure the oil drain passages are closed off with...
Forum: Overhaul 12-10-2019, 07:44 PM
Replies: 185
Views: 48,736
Posted By jcwright
This post from Don Moyer on 5.27.17 may be of...

This post from Don Moyer on 5.27.17 may be of help:

"Over the years, varnish in the oil will occasionally "glue" the valve keepers inside the retaining washer and be quite difficult to remove...
Forum: Drawings and Schematics 07-10-2010, 07:48 AM
Replies: 4
Views: 11,040
Posted By rigspelt
Cooling flow diagram

Here is a basic cooling flow diagram I made up to donate to the forum. If anyone wants one in a different format, PM me. Get the MMI manual and accompanying notes for more complete information.

I...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 04:06 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved