Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 25 of 293
Search took 0.02 seconds.
Search: Posts Made By: roadnsky
Forum: Troubleshooting 07-19-2023, 10:31 AM
Replies: 19
Views: 1,682
Posted By roadnsky
When you do the filter check... I'd suggest...

When you do the filter check...

I'd suggest you also VERIFY that the choke is closing and opening properly.
IF it isn't closing completely, when you're attempting to start from dead cold, I could...
Forum: Troubleshooting 06-27-2023, 10:25 AM
Replies: 11
Views: 1,069
Posted By roadnsky
Just a word here to be sure and use an Ignition...

Just a word here to be sure and use an Ignition Protected (MARINE) unit.
I know you mentioned you will but want to emphasize it for newbies who might be skimming this thread.
...
Forum: Fuel System 03-20-2023, 10:07 AM
Replies: 6
Views: 2,210
Posted By roadnsky
Quite a few years ago, Dave posted instructions...

Quite a few years ago, Dave posted instructions for the float settings which I copied to use whenever I clean/rebuild my carb(s).
With credit to Dave (and hopefully his permission) here it is...
...
Forum: Fuel System 03-17-2023, 10:05 AM
Replies: 6
Views: 2,210
Posted By roadnsky
SOAK IT

Let it soak in pure vinegar for a day or two.
You'll be surprised at how much gunk will fall away.

Here's a pic of the float setting Dave is talking about. Very important.
Forum: General Maintenance 10-01-2022, 11:27 AM
Replies: 5
Views: 1,172
Posted By roadnsky
Here's a shot of the "slash tube" setup that Dave...

Here's a shot of the "slash tube" setup that Dave describes.
Very likely what you have.
IF your "tube" isn't in good condition or making good connection with the flame arrestor, then you'll for...
Forum: Introductions 01-15-2022, 01:54 PM
Replies: 25
Views: 5,961
Posted By roadnsky
I believe HERE...

I believe HERE (http://www.moyermarineforum.com/forums/showthread.php?t=4727) is the thread of which Dave speaks.
I've also got the "cliff notes" version...

"When adjusting the float, err to the...
Forum: Cooling System 11-21-2021, 12:09 PM
Replies: 6
Views: 2,281
Posted By roadnsky
I would highly recommend you consider using the...

I would highly recommend you consider using the repair kit (https://moyermarine.com/product/water-jacket-side-plate-repair-kit-for-repair-of-two-bolt-holes-csot_04_307/) our host offers on this site.
Forum: Troubleshooting 11-21-2021, 12:05 PM
Replies: 18
Views: 2,606
Posted By roadnsky
Here is a simple drawing showing what Shawn...

Here is a simple drawing showing what Shawn described
Forum: Troubleshooting 10-21-2021, 06:20 PM
Replies: 18
Views: 2,606
Posted By roadnsky
If you're running with choke fully open, then...

If you're running with choke fully open, then that could certainly be the SOURCE of the exhaust smoke.
(ur running too rich and seeing unburnt fuel)

If this is indeed the case, we'll need to...
Forum: Fuel System 09-25-2021, 12:47 PM
Replies: 8
Views: 1,507
Posted By roadnsky
I think that piece looks a lot like one of the...

I think that piece looks a lot like one of the two screws holding the butterfly valve as Dave said.
Are you missing one of those screws?
See pics...
Forum: Ericson 09-01-2021, 03:49 PM
Replies: 21
Views: 6,745
Posted By roadnsky
Like Joe and Neil... I did a full DC re-wire. ...

Like Joe and Neil...
I did a full DC re-wire.
Like Joe said, using a buss bar to keep the back of the DC Panel clean works much better.

I also re-did my AC wiring from the Shore Power plug to...
Forum: Troubleshooting 08-22-2021, 11:52 AM
Replies: 11
Views: 2,457
Posted By roadnsky
HERE...

HERE (https://www.amazon.com/dp/B000BWCFLO/?coliid=I214SV92GR3S57&colid=351ASCOTMOS80&psc=1&ref_=lv_ov_lig_dp_it) is a common gauge that many of us are using.
Forum: Troubleshooting 08-01-2021, 09:38 PM
Replies: 11
Views: 2,457
Posted By roadnsky
When is the last time you inspected your exhaust?...

When is the last time you inspected your exhaust?

See HERE (https://www.moyermarineforum.com/forums/showthread.php?t=2643&highlight=exhaust) for other thoughts...
Forum: General Interest 07-26-2021, 09:16 AM
Replies: 10
Views: 2,597
Posted By roadnsky
First, welcome to the gang! 3000? Do you...

First, welcome to the gang!

3000? Do you mean when you "rev" the throttle?
1800 in gear is a bit low but not completely bad.

There a a few things to check and we can walk you thru learning...
Forum: Fuel System 07-23-2021, 10:00 AM
Replies: 21
Views: 2,700
Posted By roadnsky
Sooooo, this is directly related to WETBIRKS...

Sooooo, this is directly related to WETBIRKS original thread (https://www.moyermarineforum.com/forums/showthread.php?t=11953) but I don't think it was truly resolved.
In that thread a number of us...
Forum: Troubleshooting 07-18-2021, 09:36 AM
Replies: 5
Views: 2,114
Posted By roadnsky
That is the famous UHS (Ubiquitous Hot Spot)...

That is the famous UHS (Ubiquitous Hot Spot) discussed HERE (https://www.moyermarineforum.com/forums/showthread.php?t=3812&highlight)

Also easily remedied with the THATCH MOD...
Forum: Troubleshooting 07-09-2021, 09:08 PM
Replies: 52
Views: 10,831
Posted By roadnsky
Exhaust... Bingo! So glad you've found this. ...

Exhaust... Bingo!
So glad you've found this. (Feels good 'eh?)

I guess some of us wrote off the exhaust blockage too easily. (me) :cool:
Sorry. It seems so obvious now.

Cat-
This is one...
Forum: Troubleshooting 07-05-2021, 12:54 PM
Replies: 52
Views: 10,831
Posted By roadnsky
Please note that the coil's INPUT VOLTAGE should...

Please note that the coil's INPUT VOLTAGE should be tested between coil + and a solid ground (block). Not the coil's (-) terminal.
The small coil (-) post is not a "ground" even though one would...
Forum: Troubleshooting 07-04-2021, 12:50 PM
Replies: 52
Views: 10,831
Posted By roadnsky
Ok, I know you said you checked it, but now we're...

Ok, I know you said you checked it, but now we're gonna need to methodically go thru until we find the issue...
which, we WILL.

Can you double check or triple check you have the firing order...
Forum: Troubleshooting 07-04-2021, 09:21 AM
Replies: 52
Views: 10,831
Posted By roadnsky
Note this caution regarding the washer INSIDE the...

Note this caution regarding the washer INSIDE the Main Jet...

"CAUTION: Both the fixed jet and the 1/2" hex-headed plug of the needle assembly have hard washers to seal them after installation....
Forum: Troubleshooting 07-03-2021, 01:26 PM
Replies: 60
Views: 7,137
Posted By roadnsky
You'll open it as soon as the engine STARTS and...

You'll open it as soon as the engine STARTS and is running.

That circled area (choke arm) is indeed what John was referring to.
In the below pics you can see how is is supposed to be attached.
Forum: Troubleshooting 07-03-2021, 10:16 AM
Replies: 60
Views: 7,137
Posted By roadnsky
Look at the REAR (StarBoard) side of your engine...

Look at the REAR (StarBoard) side of your engine and locate the WATER PUMP.
(See PIC #1)
Follow the hose attached to it to where it connects to a THRU HULL.
(See PIC #2)
Your valve may look a...
Forum: Troubleshooting 07-01-2021, 11:06 PM
Replies: 52
Views: 10,831
Posted By roadnsky
I'm with Al. Sounds like you're "running out of...

I'm with Al. Sounds like you're "running out of fuel".
Yes, it'll run with a good gravity feed.

Also, double check that the black (-) wire running into the distributor is not getting pinched or...
Forum: Cooling System 06-18-2021, 10:05 AM
Replies: 4
Views: 1,892
Posted By roadnsky
Tim- Have you considered going bigger with the...

Tim-
Have you considered going bigger with the Engine intake thru hull.
I did it and the difference between the old, smaller thru hull and the new, larger one is dramatic.

A bit of expense and...
Forum: Cooling System 06-18-2021, 09:52 AM
Replies: 14
Views: 2,758
Posted By roadnsky
Mike- Soak the "old" cruddy thermostat for a...

Mike-
Soak the "old" cruddy thermostat for a day or so in pure vinegar and you'll be surprised how much it cleans up.
Then for some fun, boil it in a pot using a meat thermometer to see what...
Showing results 1 to 25 of 293

 
Forum Jump

All times are GMT -4. The time now is 01:00 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved