Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: azazzera
Forum: Ericson 12-08-2018, 02:43 PM
Replies: 237
Views: 104,393
Posted By azazzera
ss from lowes

my local lowes store didn't know the stainless alloy that was used in there hardware. My local west marine had no idea either. May get corrosion sooner than you think. I've had good luck with Bolt...
Forum: General Interest 09-12-2018, 01:56 PM
Replies: 21
Views: 5,488
Posted By azazzera
Soooo..... ya. Gas leak should be your major...

Soooo..... ya. Gas leak should be your major concern. Then with all that corrosion what is your through Hull raw water valve like. I have a 1972/3 p30 and have a cone type valve. Mine was frozen...
Forum: Troubleshooting 09-08-2017, 04:30 PM
Replies: 7
Views: 3,461
Posted By azazzera
Sudden engine shutdown

I guess it was only a matter of time. Engine has been running flawlessly since rebuild two years ago. Today I changed my antifreeze. Refilled the exchanger and started the engine. It started clean as...
Forum: Pearson 08-23-2017, 04:11 AM
Replies: 10
Views: 7,287
Posted By azazzera
Found it. The product I used on my 73 p30 head...

Found it. The product I used on my 73 p30 head window.
# 9700k14. It a square-profile oil resistant buns-n o-ring cord stock

https://www.mcmaster.com/#catalog/123/3556/=1928yon

That link...
Forum: Safety 05-18-2017, 11:43 AM
Replies: 12
Views: 9,689
Posted By azazzera
I have removed a head once. The only advice I...

I have removed a head once. The only advice I would give would be to be patient and whatever you use as a wedge or prying tool make sure it's softer than the material your working on. Even a metal...
Forum: Safety 07-29-2016, 02:54 PM
Replies: 5
Views: 9,673
Posted By azazzera
If you think it can't happen.

Not that any one would realy dismiss the possibility of a non ingnition protected devise could ignite gas vapors that's exactly what happened on the east end of Long Island today. Clearing the...
Forum: Fuel System 04-22-2016, 08:10 PM
Replies: 5
Views: 3,638
Posted By azazzera
Thats funny because i was thinking...that would...

Thats funny because i was thinking...that would make an awesome scotch glass:D

darn now I'm thirsty
Forum: ABYC and USCG Standards 09-27-2015, 12:03 PM
Replies: 5
Views: 7,170
Posted By azazzera
Did I do that.

Was I the one that sparked the addition of a new topic. I would like to think my ignorance help advance this sight. Brings a tear to my eye. If that's the case I got a lot more unknowing where that...
Forum: Ignition System 09-02-2015, 06:42 AM
Replies: 48
Views: 12,111
Posted By azazzera
I would put myself in the collum of someone who...

I would put myself in the collum of someone who gets frustrated over the amount of minutiae that has to be waded through. At the same point I love me a good education on things I never knew before....
Forum: Overhaul 02-12-2015, 09:19 PM
Replies: 227
Views: 66,870
Posted By azazzera
Don't know if your done cleaning the block but I...

Don't know if your done cleaning the block but I had great success useing a 12 gauge copper wire to dig blindly through the block. Knowing that the softer copper would not harm any part. Good luck.
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 07:55 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved