Forum: Announcements
08-08-2020, 10:17 PM
|
Replies: 34
Views: 6,053
Saying goodbye
Some sixteen years after conceiving and managing the forum on a daily basis, I am stepping away from responsibility for it, A member of the MMI family will hopefully inform you soon as to whether...
|
Forum: Ignition System
09-04-2019, 09:50 AM
|
Replies: 8
Views: 3,062
Also please be advised that if you go with an...
Also please be advised that if you go with an external regulator you'll need to keep the old disconnected regulator mounted on the alternator. It is a critical part of the ignition protection...
|
Forum: Troubleshooting
07-28-2019, 09:58 AM
|
Replies: 15
Views: 4,511
I had a small air leak in my fuel supply system...
I had a small air leak in my fuel supply system that I believe allowed air to build in the main fuel filter. The filter was the high point of the system. Same symptoms as you describe. Almost drove...
|
Forum: Ignition System
04-28-2019, 11:22 AM
|
Replies: 17
Views: 5,090
You may have answered your own question:
If...
You may have answered your own question:
If this insulation damage resulted in the wire shorting to the distributor body where it exits, it is the same effect of the coil being energized without the...
|
Forum: Exhaust System
01-25-2019, 09:10 AM
|
Replies: 6
Views: 2,799
|
Forum: General Interest
12-19-2018, 02:30 PM
|
Replies: 17
Views: 4,570
|
Forum: Polls
12-17-2018, 11:42 AM
|
Replies: 15
Views: 7,792
Warning
Neil, that is a very informative post (#13) however it should come with a warning. Virtually all of the dancing of the gage is controlled by the vacuum and the dampening of the gage. Some gages are...
|
Forum: Polls
12-17-2018, 09:22 AM
|
Replies: 15
Views: 7,792
|
Forum: Fuel System
11-29-2018, 11:18 PM
|
Replies: 27
Views: 9,075
Hi.
Hopefully the forthcoming comments will...
Hi.
Hopefully the forthcoming comments will impress upon you the hazard you face working with gasoline in a confined space.
Please have a GOOD fire extinguisher at the ready for this mess.
Also;...
|
Forum: Fuel System
11-10-2018, 02:46 AM
|
Replies: 6
Views: 2,987
Welcome to the forum.
How did the water get...
Welcome to the forum.
How did the water get into the carb? If you clean the carb but don't know how the water got to the carb what will keep it from happening again?
Water in the fuel tank is the...
|
Forum: Cooling System
10-22-2018, 02:22 PM
|
Replies: 12
Views: 4,316
Acid opening up a hole is a very real...
Acid opening up a hole is a very real possibility, perhaps even likely in your case given the sequence of events you reported but know that if it did, the affected area was paper thin to start with...
|
Forum: Troubleshooting
10-15-2018, 09:47 AM
|
Replies: 3
Views: 2,978
|
Forum: General Interest
10-11-2018, 07:37 PM
|
Replies: 7
Views: 2,653
|
Forum: Fuel System
10-05-2018, 01:17 PM
|
Replies: 8
Views: 3,638
If the rebuild was as poor as you indicate, the...
If the rebuild was as poor as you indicate, the rebuilder may have removed the needle valve seat and replaced the seat using the same gasket that was there originally. I have had that same experience...
|
Forum: Troubleshooting
09-13-2018, 04:07 PM
|
Replies: 128
Views: 31,590
|
Forum: Troubleshooting
09-13-2018, 10:28 AM
|
Replies: 128
Views: 31,590
No its not. Who told you that? And didn't we...
No its not. Who told you that? And didn't we already make it clear adding MMO to the fuel was not a remedy for sticking valves? Yet here we are covering it again.
Instead of continually blaming...
|
Forum: Exhaust System
09-13-2018, 10:22 AM
|
Replies: 13
Views: 3,741
|
Forum: Troubleshooting
08-14-2018, 09:51 PM
|
Replies: 4
Views: 2,953
No.
Please appreciate that during the...
No.
Please appreciate that during the development of the EWDS and the many decisions along the way, affordability was paramount. Earlier, more elaborate prototypes would have cost thousands but...
|
Forum: General Interest
08-13-2018, 02:33 PM
|
Replies: 7
Views: 2,780
|
Forum: Cooling System
07-19-2018, 08:59 AM
|
Replies: 14
Views: 6,695
|
Forum: Introductions
07-11-2018, 10:05 PM
|
Replies: 24
Views: 10,978
|
Forum: Introductions
07-05-2018, 12:35 AM
|
Replies: 24
Views: 10,978
|
Forum: Electrical
06-24-2018, 03:29 PM
|
Replies: 3
Views: 2,951
Cool idea, poorly executed
Terminal Tamer ...
Cool idea, poorly executed
Terminal Tamer
1. The copper bus bar is not tin plated. Once it’s developed a copper oxide or copper sulphate corrosion coating, it’s resistance will increase.
2....
|
Forum: Electrical
06-21-2018, 08:02 PM
|
Replies: 20
Views: 5,351
|
Forum: Good Guys
04-05-2018, 11:41 PM
|
Replies: 6
Views: 6,571
Wow Al, that is the complete antithesis of my...
Wow Al, that is the complete antithesis of my experience offering help and I'm sorry it happened to you. I've never expected or asked for any remuneration but forum members that I've tried to help...
|