Return to the home page...
Moyer Marine Atomic 4 Community - Home of the Afourians
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
FAQ
Members List
Search
Today's Posts
Mark Forums Read
Showing results 1 to 14 of 14
Search took
0.01
seconds.
Search:
Posts Made By:
BadaBing
Forum:
Troubleshooting
09-01-2017, 03:03 PM
Replies:
3
lacks power at high throttle
Views:
2,263
Posted By
BadaBing
After concerning that the cables are moving...
After concerning that the cables are moving correctly check to be sure that both the choke and throttle plates, in the carb, are moving through their range- from fully closed to fully open.
Then...
Forum:
General Interest
03-19-2016, 05:24 PM
Replies:
12
Modified flathead
Views:
6,110
Posted By
BadaBing
The aluminum head made on a table saw. I would...
The aluminum head made on a table saw. I would hav e that mounter and hung on a.wall as a peice of fine.art!
Forum:
Exhaust System
02-12-2016, 07:33 PM
Replies:
28
Black iron source for exhaust
Views:
24,764
Posted By
BadaBing
I rebuilt my hot section last spring. long before...
I rebuilt my hot section last spring. long before I actually needed to but I was already pulling off my head and soon replacing my head and standpipe. After spending as much as I was it seemed...
Forum:
General Maintenance
01-20-2016, 09:47 AM
Replies:
17
old gas/new gas
Views:
5,156
Posted By
BadaBing
Having lived through a battle with bad gas and...
Having lived through a battle with bad gas and its dregs I lean towards replacing the old.gas BUT I sail bays and ocean. Outside, on the ocean, a problems of bad gas and a clogged carb, when they...
Forum:
Drive Train / Propellers
01-11-2016, 09:32 PM
Replies:
13
Prop nut zinc
Views:
4,189
Posted By
BadaBing
John. I have e rooms between my vitals bearing...
John.
I have e rooms between my vitals bearing and the Back of my prop to fit the zinc. Perhaps because I.also have a flex plate between my shaft coupler and transmission. I also shifted my shaft a...
Forum:
Electrical
01-09-2016, 01:32 PM
Replies:
38
A-4 (1972) cranks slowly as if batt. is dead
Views:
13,445
Posted By
BadaBing
Gordon, Part of the tank and fuel line...
Gordon,
Part of the tank and fuel line challange, as related to ethanol is the old varnish build up in the old tanks and the incompatibility of old rubber fuel hoses with ethanol. Both are dissolved...
Forum:
Electrical
01-08-2016, 04:20 PM
Replies:
38
A-4 (1972) cranks slowly as if batt. is dead
Views:
13,445
Posted By
BadaBing
Shrek. Per Ken at Moyer Marine. Do not install...
Shrek.
Per Ken at Moyer Marine. Do not install a filter.in the sediment bowl. If any water makes its way to the bowl and is trapped there it will cause the fittings on the paper filter to rust (it...
Forum:
Electrical
01-08-2016, 04:13 PM
Replies:
38
A-4 (1972) cranks slowly as if batt. is dead
Views:
13,445
Posted By
BadaBing
I have an extra, after replacing the bowl on year...
I have an extra, after replacing the bowl on year and the mechanical fuel pump the next. I like.it so much that I keep the extra on a book shelf for dodads.
It's to small.or I would use it for a...
Forum:
Cooling System
01-02-2016, 11:22 AM
Replies:
74
Overheating Issue
Views:
45,186
Posted By
BadaBing
Another alt for back flushing. Remove the T...
Another alt for back flushing.
Remove the T stat
Seal off the inlet hose barn on the T stat fitting with a bolt and a short pc of hose
Disconnect the hose going from the pump to the T fitting at...
Forum:
Drive Train / Propellers
10-07-2015, 04:21 PM
Replies:
35
Shaft coupling is a rusty lump, how to remove
Views:
15,884
Posted By
BadaBing
A few years back I needed to drill out alot of...
A few years back I needed to drill out alot of screws for a glass and aluminum railing. To cut down the workload I ordered several left handed bits. They cut in in a counterclockwise rotation.
The...
Forum:
General Maintenance
10-07-2015, 10:59 AM
Replies:
41
Repair Quote
Views:
15,993
Posted By
BadaBing
After looking at the quote for "winterizing" I...
After looking at the quote for "winterizing" I jave a couple more thoughts.
First. Nothing in that list is actually a winterizing necessity.
No mention of flushing the engine or pumping in...
Forum:
General Maintenance
10-06-2015, 09:58 PM
Replies:
41
Repair Quote
Views:
15,993
Posted By
BadaBing
Kevin. Just my opinion and I'm sure others will...
Kevin.
Just my opinion and I'm sure others will offer theirs as well.
The first question is how mechanically inclined and or skilled you are. The suggestion by you to replace the exhaust manifold...
Forum:
Drive Train / Propellers
10-05-2015, 01:51 PM
Replies:
7
Loose engine mounts
Views:
4,983
Posted By
BadaBing
My 1974 T30 also developed sloppy engine bolts....
My 1974 T30 also developed sloppy engine bolts. In my case it was the lag portion which had, over years, violated the wood threads it pieces.
The lags were so loose that my engine was basically held...
Forum:
Exhaust System
01-30-2015, 10:08 AM
Replies:
41
Standpipe, New
Views:
10,572
Posted By
BadaBing
3 GPH sounds about right. My new stand pipe...
3 GPH sounds about right.
My new stand pipe arrived yesterday. Headed out to install it now. Then will be cranking the engine up. I gave her a little test fire yesterday with only half of the hot...
Showing results 1 to 14 of 14
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Announcements
Introductions
Drawings and Schematics
Testing Protocols
Discussion Topics
General Interest
Polls
Helpful Videos
ABYC and USCG Standards
Troubleshooting
General Maintenance
Ignition System
Electrical
Fuel System
Cooling System
Reversing Gear
Exhaust System
Drive Train / Propellers
Overhaul
Safety
Aftermarket Kits and Accessories
Specialty Tools
Moyer Marine Pin-Up's
Good Guys
Links of Particular Interest
The Wish List
Owner Discussion Groups
Discussion Groups
Alberg
Bristol
C&C
Cal
Catalina
Columbia
Dyer Glamour Girl
Ericson
Grampian
Herreshoff
Irwin
Islander
Morgan
Newport
O'Day
Pearson
Ranger
Sabre
Tartan
Classified Ads
For Sale - Engines and Engine Parts
For Sale - Other Items
Wanted to Buy - Engines and Engine Parts
Wanted to Buy - Other items
Tools wanted or offered to rent
All times are GMT -4. The time now is
10:13 AM
.
Moyer Marine Inc.
-
Archive
-
Top
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Universal® is a registered trademark of Westerbeke Corporation
Copyright © 2004-2024 Moyer Marine Inc.
All Rights Reserved