Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Overhaul

Reply
 
Thread Tools Display Modes
  #1   IP: 192.60.230.95
Old 04-08-2008, 12:11 PM
High Hopes's Avatar
High Hopes High Hopes is offline
Afourian MVP
 
Join Date: Feb 2008
Location: Fairfax, VA
Posts: 530
Thanks: 0
Thanked 1 Time in 1 Post
Compression - Good enough, or Not

I am reassembling my engine after a valve job and many minor fixes. With the head back on, with the manifold still off, and cranking by hand I observed the following. There is little oil in the engine.

- Compression was about 30 psi with a dry head.

- Compression went to about 50 psi with some Marvel Mystery Oil (MMO) poured into the sparkplug holes.

- Compression across all cylinders was uniform.

- Two intake valves were spitting oil spray out their manifold port. This seemed to decrease with time either because the valves were seating better or because the MMO all drained out with previous cranking.

- I heard a squirting / squeezing oil noise. I fear this may have been oil blowing by the pistons. I'm not sure where else the oil could have been going. This was only heard when the compression gauge was in a cylinder. It might have been an oozing exhaust port?

Questions:

(1) Is hand cranking a suitable way to check compression? If not, how should it be measured?

(2) Should I continue to assemble the engine, fill it with oil, run it, and then measure compression again?

(3) Or, should I bite the bullet and drop the crank and go for the whole nine yards and do a complete overhaul? I really only need about five more years out of my A4 before I move to a bigger boat (I hope).

Steve
Reply With Quote
  #2   IP: 204.145.183.5
Old 04-08-2008, 04:07 PM
Don Moyer's Avatar
Don Moyer Don Moyer is offline
 
Join Date: Oct 2004
Posts: 2,811
Thanks: 0
Thanked 183 Times in 124 Posts
Steve,

I'd put at least a quart or two of oil in the crankcase so that the level is
above the pick up screen. Then remove the plugs and turn the engine over on
the starter. Most engines will develop around 20 psi at starter RPM which
will be better for your rod and main bearings and will give you a more
consistent compression reading than hand cranking will.

Do you remember what the compression was before your valve work? As long as
it was 85 psi or above I would hope that once the valves seat (which usually
will not happen until you run the engine for at least a few minutes) you'll
have plenty of compression to see you through the next 5 years.

Don
Reply With Quote
  #3   IP: 70.108.202.225
Old 06-06-2008, 10:29 PM
High Hopes's Avatar
High Hopes High Hopes is offline
Afourian MVP
 
Join Date: Feb 2008
Location: Fairfax, VA
Posts: 530
Thanks: 0
Thanked 1 Time in 1 Post
Don,

Just to follow up. Compression was 105, 102, 96, & 105 measured a week ago. There might be a stuck oil ring on #3, but didn't see the benefit of tearing down the engine for this one item. Maybe some MMO will work it loose.

Steve
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Valid Compression Test jkenan Troubleshooting 11 12-18-2013 09:14 PM
Low Compression forcenine Fuel System 7 04-04-2008 10:19 PM
Lower compression in non-adjacent cylinders rods a4 Troubleshooting 4 08-24-2007 02:40 PM
Compression and Power Loss Gavin Peters Troubleshooting 6 08-24-2007 02:40 PM
compression on atomic-4 rbtmoon Troubleshooting 2 06-07-2006 08:18 AM


All times are GMT -4. The time now is 04:35 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved