Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Owner Discussion Groups > Discussion Groups > Morgan

Reply
 
Thread Tools Display Modes
  #1   IP: 24.211.177.67
Old 10-28-2012, 09:16 PM
dburns's Avatar
dburns dburns is offline
Senior Member
 
Join Date: May 2012
Location: Raleigh/Topsail Beach NC
Posts: 32
Thanks: 4
Thanked 5 Times in 4 Posts
140 degree thermostat?

My raw water a4 has run at 180+ degrees for the past five years. Vinegar flushes and pressure flushes with the water hose haven't changed anything. I finally pulled the thermostat and it had 140 stamped on the bottom, so I assume it's a 140 degree thermostat. It was cleaned in vinegar and placed in water on the stove. It opened at 160 degrees. Is it defective? If so, should I replace it or just leave it out and use a bypass valve?

I've been lurking on the site for the five years since I purchased JaVa.

The engine is an early '70s model that replaced the original 1963 model in my Morgan Tiger Cub, best I can tell. Can't imagine what caused the replacement. The engine was covered in rainwater for several years when JaVa was a derelict in a boatyard in the '90s and early 2000s after hurricane Fran. The previous owner r&r'ed it and it runs like a top, starts easily and has only stranded me when a coil failed on a 200 mile trip two years ago. (At the worst possible time, half-way through the extremely narrow Alligator/Pungo River Canal at night, with tugs/barges coming every hour. That's a story unto itself...)

After reading all the posts I can find about thermostats, I hope to get an opinion or two.
Reply With Quote
  #2   IP: 96.229.18.9
Old 10-29-2012, 09:02 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
dburns, first welcome to the Afourian forum!
If you have been running in salt water at 180 you probably have a good coating of calsefied salts in the engine. I suggest that you flush well preferably with acid before doing anything. The T'stat should open at the stated temp or it is faulty. The t'stats can be a problem around salt water when RWC'd as anytime the BLOCK gets to 160 the calsefied salts can deposit and it starts again. You need to stay below that temp. Running with the t'stat is a choice regarding the engines temp vs longivity according to most. I have run for 26 years without one and have had no issues with my 42 year old RWC'd beastie. I ran until last year with the standard bypass configuration and would show around 125 when cruising and 150 after shutting down. I have since modified the plumbing and now cruise at 135 and still hit 145~150 after shutting down an improvement in my humble opin.
Where and in what temp waters do you play?

Dave NEptune
Reply With Quote
  #3   IP: 24.224.206.117
Old 10-29-2012, 12:21 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
Thumbs up I second that.

I think along the same lines as Dave....no T-stat and do an muriatic acid flush of the engine asap. It will stay cool for you after that.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
  #4   IP: 8.19.13.19
Old 10-29-2012, 12:23 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by dburns View Post
If so, should I replace it or just leave it out and use a bypass valve?
Do you have a bypass valve now? I can't tell from the post.

In a RWC engine, with a properly functioning thermostat, you need adequate output from the water pump, clean engine passages to let the water flow and the heat to transfer and you should be good to go.

1. Acid flush.
2. Valve on the bypass if you don't have one already.
3. Check the water flow through the engine. This is best done by pulling the hose off at the hot section water injection point and aiming it into the cockpit. Should be like a garden hose at ~ 1500 RPM.

TRUE GRIT
Reply With Quote
  #5   IP: 24.211.177.67
Old 10-29-2012, 06:43 PM
dburns's Avatar
dburns dburns is offline
Senior Member
 
Join Date: May 2012
Location: Raleigh/Topsail Beach NC
Posts: 32
Thanks: 4
Thanked 5 Times in 4 Posts
I sail out of Topsail Beach NC. The water temperature can easily get into the 80s and air temperature 90s to 100 in the hotter months.

I just got the parts and pieces for a bypass valve and installed it. Looks like an acid flush in the making for this weekend. Two questions about the flush procedure:

Is the thermostat removed or left in?
What position is best for the bypass valve?

Many thanks for the advice!
Reply With Quote
  #6   IP: 24.224.206.117
Old 10-29-2012, 08:18 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
I would leave the T-stat out and leave the by-pass 1/2 open....keep an eye on your temp guage...it might even stay as low as 130...

also...I use NGK XR4 plugs...a bit hotter than your everyday A4 plugs. They keep the combustion chamber clean and just finished my second year on them without a hitch. So, no t-stat and the plugs will keep the carbon at a minimum...it works. Plugs number 1 to 4 ..right to left.
Attached Images
 
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
  #7   IP: 24.152.131.155
Old 10-29-2012, 08:35 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Bypass position for the flush procedure is closed and as Mo said, thermostat removed.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #8   IP: 184.0.105.143
Old 10-29-2012, 08:44 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by dburns View Post
Is the thermostat removed or left in?
What position is best for the bypass valve?

Many thanks for the advice!
Flush procedure...

http://www.moyermarine.com/forums/sh...pressure+flush
Attached Images
File Type: pdf Acid Flush Procedure 1.pdf (9.6 KB, 1271 views)
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
  #9   IP: 70.53.226.252
Old 10-30-2012, 09:40 AM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
''also...I use NGK XR4 plugs...a bit hotter than your everyday A4 plugs. They keep the combustion chamber clean and just finished my second year on them without a hitch.''

Not only are they hotter, their reach, reaches the center of the combustion chamber. I dislike the regular plugs for that reason.
Or is it, they are hotter because their longer reach makes them hotter?

Anyways, I'm sold on them.
Reply With Quote
  #10   IP: 24.224.206.117
Old 10-30-2012, 11:09 AM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
Thumbs up

Sony...I think you are the first convert to the NGK XR4's...glad you like 'em too. Mine are in a photo in post #6....two years on those as you see them.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.

Last edited by Mo; 10-30-2012 at 11:48 AM.
Reply With Quote
  #11   IP: 108.28.109.76
Old 10-30-2012, 11:24 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by Sony2000 View Post
...Or is it, they are hotter because their longer reach makes them hotter?...
I believe that its the longer electrode and insulator that makes them hotter. It provides more thermal resistance to the flow of heat from the tip of the electrode to the body of the plug and the block, causing the tip reach a higher temperature at equlibrium.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #12   IP: 8.19.13.19
Old 10-30-2012, 12:10 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
dburns

The standard advice is to remove the thermostat before acid flushing. I,like you, knew that my thermostat was working correctly. So rather than remove it here's what I did:
In a 5 gallon bucket mix the acid and water. Remember to add acid to water slowly with stirring. Eye protection is a good idea.
Run a tube from the water pump to another 5 gallon bucket. Supply enough water to this bucket to keep the water pump pumping. Start the engine and run it long enough and fast enough to get the thermostat fully open. Idle back and clamp or restrict the bypass hose. Put the intake tube into the acid and aspirate it into the engine. While the acid is sitting in the engine you can rig up your catch system. Start the engine and aspirate 5 gallons of water into it. Stop the engine and remove the catch bucket. Finally start the engine and flush it with fresh water.
===============================
The water temp in my area is 60*-70*. I run at ~ 150* - about 80* higher than the outside water temp (RWC). I have the original 3 spring thermostat which does restrict the flow a bit. If you can get your engine temp down to 160* in 80* water, with a thermostat, you will have done good.
==============================
The amount of bypass restriction necessary is different for each engine. One size does not fit all. Here was my experience:
The Moyer kit came with a fixed restrictor and a valve. With the restrictor in place and the valve wide open the temp was under 120*. With the restrictor removed and the valve wide open I run at 150*. If I close the valve 1/4-1/3 turn the temp goes down to ~ 125*. Apparently the wide open valve supplies the amount of restriction my engine needs.

Have fun.

TRUE GRIT
Reply With Quote
  #13   IP: 24.211.177.67
Old 11-01-2012, 09:01 PM
dburns's Avatar
dburns dburns is offline
Senior Member
 
Join Date: May 2012
Location: Raleigh/Topsail Beach NC
Posts: 32
Thanks: 4
Thanked 5 Times in 4 Posts
All of this helps a great deal--many thanks to everyone. Now for the really tough decision: leave the thermostat in or take it out for the duration.
Reply With Quote
  #14   IP: 107.0.6.242
Old 11-01-2012, 09:10 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking

I agree with the others; lose that thermostat (but keep it on board)....but I gotta know; what were you doing in the Alligator/Pungo Canal at night?
Reply With Quote
  #15   IP: 24.224.206.117
Old 11-02-2012, 06:22 AM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
Smile T-stat out

T-stat out and welcome to the world of trouble free cooling. Install by-valve (MMI has them)... I do a muriatic acid flush every 2 or 3 years just to ensure passages remain clean...run the hotter plugs. Wait for it. The day may come when you have to push hard in chop and it's nice to look down at that temp gauge and see you are nowhere near the verge of overheating. You may indeed watch your gauge and maintain a happy little grin as the spray hits you in the face Peace of mind.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
  #16   IP: 66.0.74.26
Old 11-02-2012, 01:08 PM
dburns's Avatar
dburns dburns is offline
Senior Member
 
Join Date: May 2012
Location: Raleigh/Topsail Beach NC
Posts: 32
Thanks: 4
Thanked 5 Times in 4 Posts
Quote:
Originally Posted by hanleyclifford View Post
I agree with the others; lose that thermostat (but keep it on board)....but I gotta know; what were you doing in the Alligator/Pungo Canal at night?
The Alligator/Pungo canal at night. It's a long story with a very happy ending.

We motored into the 18 mile canal around 2pm on a hot late June day. Should have been on the other side between 6 or 7 headed south for Dowry Creek for the night. Plenty of time, since there was daylight until 8:30 or so. Plenty of time until the engine died around 4pm, just ahead of an oncoming tug and barge. We drifted toward the shore, out of the way, got an anchor out and following Murphy's first and second laws, we then went up on a snag thanks to the wake of the passing vessel.

Only took an hour or so to winch JaVa off the snag and get the engine started.

At that point I suspected, but didn't know the coil was the issue, believing it was a only a fuel issue. Drained water from the fuel filter and got the engine running. It's now after 5pm. Almost an hour later, the engine dies again. Using the dinghy and outboard, we very slowly made it to the only marker on the canal and tie up to it, since there's no room to anchor. We're just past half-way down the canal. Can't raise SeaTow on ch16, Verizon has no bars for the cell phone. The Hobucken CG station is raised and they call SeaTow for us and relay our situation. Now it's nearly 8 pm and we wait for SeaTow to arrive. They have to come from Little Washington in a 20-25kt SW Pamlico breeze, making for 3 ft swells, 3-4 ft apart.

Finally, around 10pm off we go with a tow.

The good news in all of this and the happy ending is that my bride wasn't on board, so I only have to revisit this adventure when I see one friend!
Reply With Quote
  #17   IP: 75.62.253.251
Old 11-02-2012, 05:12 PM
dvd's Avatar
dvd dvd is offline
Senior Member
 
Join Date: Dec 2008
Location: San Joaquin Delta, California
Posts: 449
Thanks: 3
Thanked 12 Times in 8 Posts
I have a T-Stat and it works great. Got the upgrade moyer T-stat and T-stat kit with bypass and I've been happy and cool motoring ever since. I am in mostly fresh water but occasionally salt when I go to SF Bay. Should we all lose our T-Stats??

dvd
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Thermostat installation instructions ( with spacer kit and original housing ) seapadrik Cooling System 11 07-06-2011 02:35 PM
Cheap thermostat possibility msauntry Cooling System 8 03-31-2009 09:43 AM
New Products From Moyer Marine Don Moyer Cooling System 0 10-05-2005 02:03 PM
No Thermostat Action mike7a10 Cooling System 0 09-06-2005 06:38 PM
180 degree thermostat lhbradley Cooling System 0 11-03-2004 10:40 AM


All times are GMT -4. The time now is 08:02 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved