Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Interest

Reply
 
Thread Tools Display Modes
  #1   IP: 74.114.143.179
Old 05-18-2020, 05:13 PM
Tripaddle Tripaddle is offline
Senior Member
 
Join Date: Sep 2015
Location: Lancaster, VA
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
On-board tool list

I’ve decided to empty out the tool shed that my sailboat has become. It’s handy having a lot of tools on board but I’d like to shed some weight, and lighten the sailboat too. Wondering if anyone has a list of what tools they wouldn’t leave the dock without. I’m talking daily to a few days, no crossing seas.
__________________
David
1976 Cal 2-27
Lancaster, VA
Charlotte, NC
Reply With Quote
  #2   IP: 47.142.128.25
Old 05-18-2020, 05:17 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
1/4 inch socket set.

ex TRUE GRIT
Reply With Quote
  #3   IP: 165.225.38.121
Old 05-18-2020, 06:28 PM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
let me grab a beer... this is going to be a long thread!! between those who would go pretty light, and those who cannot drop the lines without a water pump, a coil, spark plugs + cables, a voltmeter and 2 back-up anchors etc...

But clearly I need to do the same cleaning... Previous owners had kept stashed multiple ignitor points (now an electronic ignition), and I did not do a better job at cleaning the boat. So clearly some good lessons to learn here.
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
  #4   IP: 67.169.215.221
Old 05-18-2020, 06:46 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
I basically use my checklist for off-roading... minus the air compressor.

Socket set - but I would go 3/8"
combo standard wrench set plus maybe metric for an outboard
Small battery operated drill / driver and modest set of drill bits
Combo set of driver bits
Screwdriver set or one of 6-in-1 screwdriver in good shape
Big screwdriver or small pry bar
A large adjustable wrench
Small and large channel-locks
Vise grip
Pliers
diagonal cutters
Utility knife
Wirestripper
20' of 4 conductor - 16 gauge trailer wire (for emergency patches)
various wirenuts
Black electric tape
DUCT TAPE (any color )
Jumper Cables
various hose clamps
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 05-18-2020 at 06:46 PM. Reason: spelling
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
TimBSmith (07-17-2021)
  #5   IP: 72.218.38.55
Old 05-19-2020, 09:32 AM
alcodiesel's Avatar
alcodiesel alcodiesel is offline
Senior Member
 
Join Date: Oct 2015
Location: Norfolk, VA
Posts: 293
Thanks: 48
Thanked 68 Times in 52 Posts
I like Ron's list.
I substitute crimp connectors for wire nuts

add
soldering gun, solder
crimper for connectors
bolt cutter
electrical tape
various glues and epoxies
hammer
various oils
more electrical wire
__________________
Bill McLean
'76 Ericson 27
:valhalla:
Norfolk, VA
Reply With Quote
  #6   IP: 138.207.175.104
Old 05-19-2020, 09:38 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Incrementals:

VOM (volt/ohmmeter)
Rescue Tape.

Bill
Reply With Quote
The Following User Says Thank You to Administrator For This Useful Post:
lat 64 (05-19-2020)
  #7   IP: 155.186.124.219
Old 05-19-2020, 10:00 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
4 the list

Aluminum clothes line coated wire and a "shot glass" .

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
TimBSmith (07-17-2021)
  #8   IP: 108.172.148.65
Old 05-19-2020, 11:42 AM
Marty Levenson Marty Levenson is offline
Senior Member
 
Join Date: Nov 2004
Location: Bowen Island, BC
Posts: 679
Thanks: 91
Thanked 42 Times in 36 Posts
stethoscope

stuffing box wrenches.
several grades of sandpaper.
ss hose clamps.
magnet on a stick.
Lists will vary for cruising vs day sailing.
__________________
Marty
1967 Tartan 27
Bowen Island, BC

Reply With Quote
  #9   IP: 107.77.97.101
Old 05-19-2020, 12:34 PM
lat 64's Avatar
lat 64 lat 64 is offline
Afourian MVP
 
Join Date: Oct 2008
Location: Fairbanks, Alaska
Posts: 1,964
Thanks: 39
Thanked 240 Times in 157 Posts
Adapt

vice grips to be sure!
I looked for an image and found this(attached).

Me;" Master Yoda, I'm trying to fix the engine!"
Yoda;"There is no trying, only doing."
Attached Images
 
__________________
Whiskeyjack a '68 Columbia 36 rebuilt A-4 with 2:1

"Since when is napping doing nothing?"
Reply With Quote
The Following User Says Thank You to lat 64 For This Useful Post:
ronstory (05-20-2020)
  #10   IP: 137.103.82.227
Old 05-19-2020, 01:38 PM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
I tend to trend towards the "rebuild engine in mid-cruise" supply level, but I did decide the extra starter weighed a ton and took it home.
If you race, then you need two screwdrivers and vicegrips, but not the big vicegrips
* I impressed my brother when the alternator died mid cruise. In about 20 or 30 minutes we were back underway with the spare alternator. He thought we were going to be on solar power the rest of the trip.
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
Marian Claire (05-19-2020)
  #11   IP: 24.152.132.140
Old 05-19-2020, 10:56 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I carry two tool kits similar to the one pictured plus a few additional specialty tools. The kits fold flat and stow easily.
Attached Images
 
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #12   IP: 137.103.82.227
Old 05-20-2020, 07:13 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Years ago I found a socket set at Sears that I really like that uses these sockets. I don't know if it still an be found as a set, but they still sell the sockets. I have the huge $300 Craftsman set at home with all the 1/4, 3/8, and 1/2 inch sockets and so on, but that thing is huge and heavy and does not like being carried sideways, so it would be terrible for a boat.
The set I have holds tight when closed, which is important on a boat. It does not do everything, I have some extra extensions and a 1/4" drive and some small sockets in my toolbox as well.
Some hints for buying a socket set:
1. Do NOT cheap out on this or you will pay with rounded off nuts and bolts.
2. Check the smaller sizes. There are a couple sizes like 11/32s that are common with electrical stuff and so on that many sets skip and I definitely use them.
3. Make sure they stay put in their case when shaken and moved.
Attached Images
 
Reply With Quote
The Following 2 Users Say Thank You to joe_db For This Useful Post:
Administrator (05-20-2020), TimBSmith (07-17-2021)
  #13   IP: 137.103.82.227
Old 05-20-2020, 07:22 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Some other tools to consider:
1. A strap wrench. I sprained/strained my wrist trying to get a Racor element off. A strap wrench will do this and oil filters too no problem.
2. Ratchet wrenches. These are very useful for getting the exhaust flange off the manifold. I don't have a full set, but I do have 1/2" and 9/16".
3. An impact driver socket for the temperature sensor. If you haven't ever taken yours off, it probably isn't ever going to come off without this and a long breaker bar.
4. A "grabber" that can reach under the engine and pull whatever you dropped under there out. Not that I have ever done that....
5. A bunch of test leads with alligator clips. These are quite useful for electrical testing.
6. Hydraulic crimpers. I can put terminals on wire up to 2/0 or maybe 4/0 gauge wire in 30 seconds instead of running to the local battery store or using the Nicropress machine at West when they aren't looking.
7. An IR laser thermometer. These are cheap and very useful. Do NOT use them on people. I saw some government official on TV using it on people to see if they had Covid-19. Not only is shining a laser at someone's face rude, it is calibrated for the emissivity of metal, not skin. The reading will be WAY off.

Last edited by joe_db; 05-20-2020 at 07:25 AM.
Reply With Quote
  #14   IP: 165.225.38.121
Old 05-20-2020, 09:38 AM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
and because I had to use them once... I would never leave the dock without a good set of those, knowing exactly where they are stored.
Attached Images
 
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
The Following 2 Users Say Thank You to Surcouf For This Useful Post:
Administrator (05-20-2020), TimBSmith (07-17-2021)
  #15   IP: 99.30.185.198
Old 05-20-2020, 09:39 AM
thatch thatch is online now
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
"Dental floss?"

Recently, while doing some work on a friend's boat, I discovered a very creative way to make an "O" ring of sorts. Someone had wrapped about 25' of dental floss around a shift lever shaft that extended through a bulk-head, basically making an O-ring. It filled in a gap and most likely kept water from entering a space that had widened over the years. The floss still seemed to be in good shape despite having been exposed to the elements for quite some time. "Live and learn".
Tom
Reply With Quote
The Following 3 Users Say Thank You to thatch For This Useful Post:
Dave Neptune (05-20-2020), Surcouf (05-20-2020), TimBSmith (07-17-2021)
  #16   IP: 155.186.124.219
Old 05-20-2020, 10:10 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Tom, the "floss" is a great idea. I have not seen an O-ring fashioned before. I have seen braided fishing line used as a temporary packing though.

One important thing to me is a "rechargeable Dremel set". It has saved my but more than once.

Another is a big "nylon" hammer, for knocking things loose and causing no dents or major collateral damage.

The coated aluminum clothes wire is light and easy to bend, twist and tie. It also makes a great hook for grabbing and an excellent rod for poking out lines. The coating works good in case you have to poke around electrical stuff. I even use it cruising to hold things out of the way, an easy fabrication that won't rust or mar surfaces.

One more specialty tool is a "magna-visor", you can magnify and still have both hands.

That leaves the shot glass, it is actually metal.

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
ronstory (05-20-2020), thatch (05-20-2020)
  #17   IP: 137.103.82.227
Old 05-20-2020, 11:27 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Quote:
Originally Posted by Surcouf View Post
and because I had to use them once... I would never leave the dock without a good set of those, knowing exactly where they are stored.
I haven't used mine on my boat for an emergency yet, but I have used them to change seacocks without hauling the boat and I have used them to save other boats.
Reply With Quote
  #18   IP: 138.207.175.104
Old 05-20-2020, 12:54 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Thinking outside the box

GOOD first-aid kit
CPR face mask
Narcan
EpiPen

Plus this thought:
Quote:
I sprained/strained my wrist trying to get a Racor element off.
These are ridiculous. I once had to sacrifice the filter element to replace the filter itself.

Bill

Last edited by Administrator; 05-20-2020 at 12:57 PM.
Reply With Quote
The Following User Says Thank You to Administrator For This Useful Post:
TimBSmith (07-17-2021)
  #19   IP: 137.103.82.227
Old 05-20-2020, 01:00 PM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Quote:
Originally Posted by Administrator View Post
GOOD first-aid kit
CPR face mask
Narcan
EpiPen

Plus this thought:


These are ridiculous. I once had to sacrifice the filter element to replace the filter itself.

Bill
This is why I use $12 Sierra filters now. They pay for themselves in not having to buy Ace bandages alone, let alone being cheaper filters
Speaking of toolkits for fixing people, I was at the drugstore stocking up for a Bermuda trip. It involved 3 kinds of antibiotics, 2 kinds of narcotics, scopalamine, and some other stuff. I was 16. When I handed the druggist the stack of prescriptions, he took a long look at me, and then said "Son, what kind of disease do you HAVE to need all this!"

Last edited by joe_db; 05-20-2020 at 01:04 PM.
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
TimBSmith (07-17-2021)
  #20   IP: 67.169.215.221
Old 05-20-2020, 03:29 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
I think it would be interesting to see what tools you would leave at the dock if you were trying to 'live light' and will the goal of fixing most things to last for a few days until you can fix it right. In my case that means I would leave pull my 5 crimpers off and go with wirenuts. Yes, wirenuts are 'bad' on a boat... but IMO not if it's just get home.

Funny story. One time out 4-wheeling a wiring harness in a friends truck somehow got snagged and *then* somehow got pull into the open knuckle u-joint and just shredded (a million to one shot I never would have thought possible). While it started off as just headlight wires by the time it was done it had snaked in the part of the engine wiring harness as well and the truck was DOA in the middle of nowhere.

We were stealing bits of wire in pieces from other vehicles and their stereo/speaker, twisting wires and black tape to get enough engine wiring to make it go.

That's when I started putting the 20' of 4 conductor cheapo trailer wiring and wire nuts in all the rigs (and boat). With that, we could have not only got the engine running, but the headlights too.
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 05-20-2020 at 09:06 PM.
Reply With Quote
  #21   IP: 100.36.65.17
Old 05-21-2020, 11:19 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
One addition I just made to my onboard toolkit after 10 years of cruising is a 3/8" flare nut wrench.

This was because a standard open-end wrench or an adjustable crescent wrench tends to round off the soft brass flare nuts on the carb's scavenge tube, making it almost impossible to remove in the tight confines of my engine compartment.

After struggling for over an hour to remove the damaged flare nut, I finallty wised-up and brought a flare nut wrench from home. It took it off on the first try.

I found a 3-wrench no-name set on Amazon for ~$12 and put it on the boat.

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

There's nothing quite so satisfying as having the right tool for a job.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
The Following User Says Thank You to edwardc For This Useful Post:
Surcouf (05-21-2020)
  #22   IP: 37.19.212.29
Old 07-15-2021, 12:11 PM
idreamOfSailing idreamOfSailing is offline
Senior Member
 
Join Date: Jun 2018
Posts: 37
Thanks: 7
Thanked 0 Times in 0 Posts
which flaring tool to use?

A bit off topic but I don't know how to start a new thread (looked in FAQ to no avail). I'm thinking of moving the location of my oil gauge and so think I may as well redo the copper line from it to my OPSS. My question is, do I single-flare or double-flare the line terminals? Thanks.
Reply With Quote
  #23   IP: 38.27.109.137
Old 07-15-2021, 02:59 PM
W2ET W2ET is offline
Former Admin
 
Join Date: Oct 2008
Posts: 184
Thanks: 264
Thanked 116 Times in 69 Posts
Scroll down this thread for a how-to re threads..

Bill

Last edited by W2ET; 07-15-2021 at 03:20 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Head Removal Tool Hughes35 Overhaul 24 04-19-2011 04:44 PM
Handy tool to extract seals from water pump mcclen Cooling System 0 07-04-2010 06:45 PM
on board repairs william wilson Introductions 3 03-30-2010 09:11 PM
New forum search tool? rigspelt General Interest 2 04-09-2009 09:45 AM


All times are GMT -4. The time now is 09:54 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved