Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 63.139.175.34
Old 01-13-2020, 01:12 PM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
Another stalls when put into gear thread

I'm in the process of getting an old A4 running in my "new to me" Catalina 30. After discovering and replacing a broken exhaust valve the engine still doesn't want to idle up and sometimes stalls when put into gear. I've checked the prop for fouling, checked and rechecked the firing order and timing, checked the exhaust (and even ran it disconnected to verify potential clogs/collapses) I've got compression and I have spark to all cylinders. I'm about to rebuild the carb but noticed last night that the ignition coil had oil in the top of it where the coil wire connects. Is this normal and could this be the source of my grief?
Reply With Quote
  #2   IP: 155.186.124.219
Old 01-13-2020, 01:49 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
The coil should not leak oil, replace it. Not wanting to idle in gear is usually "tune" related. IE idle speed, idle mixture, timing and/or stuck C-advance or an air leak. Once you know the timing and spark are good and it still dies it would be time to look to the carb, fuel and fuel delivery.

Did you check the C-adv? How do the plugs look, piics would be nice? Are you sure the valves are adjusted properly and supplying good compression?

Dave Neptune
Reply With Quote
  #3   IP: 70.185.132.167
Old 01-13-2020, 03:20 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Is the choke adjusted correctly so the choke is open\closed all the way when you think it is?

ex TRUE GRIT
Reply With Quote
  #4   IP: 67.176.202.156
Old 01-13-2020, 03:56 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
well, I am assuming "late" model A4. Does it have distributor points or electronic ignition?
Reply With Quote
  #5   IP: 99.255.196.148
Old 01-13-2020, 05:18 PM
Bratina Bratina is offline
Senior Member
 
Join Date: Jun 2015
Location: Toronto, Ontario
Posts: 96
Thanks: 126
Thanked 26 Times in 17 Posts
I chased two stalling problems for a while, which I eventually fixed by:

1: clean fuel. I had around 10% water in my fuel, the engine would run at low power, but stumble and die in gear or under load. I pumped out the tank, replaced the Racor, changed a deck-fill o-ring (water had to come from somewhere).

2: low fuel pressure due to a blocked polishing filter. Same symptoms; I added a small in-line fuel pressure gauge after this incident, which would have narrowed down the possibilities rapidly. Changing the filter immediately cured this.

Are you sure you have clean, dry fuel? Do you have a fuel pressure gauge? I used a $20 'Mr Gasket' which users here recommended.
Reply With Quote
  #6   IP: 69.250.111.245
Old 01-13-2020, 09:06 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Thumbs up

Catfish, Welcome from a fellow C-30 owner!!

These are all good questions, and each one valid. Work thru all responses one by one and we can help. In addition to the data points you've already provided, we are gathering data to help diagnose the potential problem. If you aren't sure how to answer one, just ask, we can help (Advance, Electronic ignition, etc.)
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #7   IP: 70.185.132.167
Old 01-14-2020, 12:49 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Another Thought Or Two

Quote:
Originally Posted by Catfish View Post
the engine still doesn't want to idle up and sometimes stalls when put into gear.
How warmed up is the engine then you try to back off on the idle RPMs and shift into gear?

A cold A4 needs to warm up at fast idle for a minute or two before it will idle normal and shift into gear without stalling. A bit of choke usually will speed up the warm up process.

A good diagnostic test is to see if the engine runs better with a bit of choke. If it does there is a problem in the fuel system.

Welcome to the forum. Your engine will run correctly.

ex TRUE GRIT
Reply With Quote
  #8   IP: 35.143.197.21
Old 01-14-2020, 03:38 AM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
Whew. That's alot to take in lol. As far as timing I've just checked with a light to make sure I had the distributor close. I tuned by ear and the timing mark is close at idle. The engine now starts immediately, runs great, and has a responsive throttle. However when eased into forward gear struggles to stay running. I verified the choke was in the open position and the engine starts to bog down when I apply it while running. I ordered a replacement coil and cleaned the carb out. I also verified operation of the electric fuel pump and oil pressure switch. Hopefully I can find some time to get back at it tomorrow evening. I plan to delve into the distributor. It's a late model engine with points ignition. I haven't checked the advance or springs yet. Sorry if I'm missing some answers to your questions. I didn't expect so many responses....but I appreciate them!
Reply With Quote
  #9   IP: 138.207.175.104
Old 01-14-2020, 08:27 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Just curious... Does it also bog down when you do the same thing in reverse?

Bill
Reply With Quote
  #10   IP: 71.38.107.125
Old 01-14-2020, 11:02 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
When was the last time you checked your STUFFING BOX?
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
  #11   IP: 174.228.15.113
Old 01-14-2020, 12:23 PM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
It goes into reverse just fine and stays running. I have spun the prop shaft by hand in neutral with ease, but I have not taken the stuffing box apart for repacking yet.
Reply With Quote
  #12   IP: 71.38.107.125
Old 01-15-2020, 11:51 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Here is a quote from the FAQ's. Note the mention of exhaust repair AND item #4

What would cause my engine to run with almost no power in forward, while it runs OK in neutral? It also seems to have more power in reverse than in forward.

This condition is usually the result of low power caused by something that was done incorrectly during recent engine maintenance.
The reason the engine seems to run better in reverse is because the reverse mode has a 1.7 to 1 gear reduction. Here are some examples of maintenance problems that we've heard about:



Three to five times each year, spark plug leads were found to be installed in an improper sequence following a tune up! Cylinders 2 and 3 can apparently be reversed, and the engine will run fairly well in neutral, but will have practically no power in forward.
According to one caller, his plug wires were reversed for an entire season before he found the cause of his power loss.



Another recent maintenance "oops" involved a minor repair of the exhaust system which required that the manifold be removed. On reinstallation, the old gasket was improperly installed, resulting in intake leaks and very poor power under load. 

Assuming that there was absolutely nothing done to the engine since it was last running OK, check the following areas for potential problems:


1) Check for something hanging on to the prop.


2) Check basic integrity of the engine by a quick compression check. For the purpose of diagnosing a major power loss, a simple check using your thumb over each spark plug hole is more than adequate. If your compression is sufficient so as to make it impossible for you to hold your thumb over each spark plug hole while cranking the engine with the starter, the cause of your power loss is not a major mechanical failure. If compression is weak in two adjacent cylinders, or water is observed in any of the combustion chambers, the head gasket has probably failed. If compression is "zero" in any of the cylinders, a valve has probably stuck open. If you are using a compression gauge, compression values over 80 psi are considered adequate.



3) Check for proper carburetor function. Normally, an Atomic 4 will accelerate almost "explosively" as you flick the throttle forward. If there is any hesitation or mild backfiring, a lean condition caused by dirt in the main jet is the most frequent cause. In most cases, a problem related to a fuel issue will manifest itself in neutral as well as in forward, but in mild cases, a lean condition might be missed in neutral, but will surely show up under load.



4) Check for proper ignition. As in the case of subtle lean fuel mixtures, there are subtle ignition problems that can show up under load but not necessarily in neutral. In this category, plug condition is the best indicator. If one plug is noticeably blacker (or oilier) than the rest, look for the relatively few things that can affect only one plug, such as the plug itself, the plug lead, or a cracked distributor cap. If all the plugs are badly fouled, check things that can affect all plugs, such as a loose condenser, badly worn points, shorting coil (or oil leaking from the coil), cracked distributor cap, or a bad coil lead.
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following 2 Users Say Thank You to roadnsky For This Useful Post:
AFisch (02-05-2020), thatch (01-15-2020)
  #13   IP: 35.143.197.21
Old 01-15-2020, 06:42 PM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
That all makes sense. I was able to get the carb cleaned and reinstalled and the stuffing box repacked. A small improvement as I can now get it into gear without it dying but still doesnt want to throttle up. I inspected the plugs and all appeared black soot covered. Would that be a weak spark indicator? My new coil I'd scheduled to arrive tomorrow. Again, thanks for the advice and feedback everyone.
Reply With Quote
  #14   IP: 99.255.196.148
Old 01-15-2020, 07:28 PM
Bratina Bratina is offline
Senior Member
 
Join Date: Jun 2015
Location: Toronto, Ontario
Posts: 96
Thanks: 126
Thanked 26 Times in 17 Posts
Quote:
Originally Posted by Catfish View Post
That all makes sense. I was able to get the carb cleaned and reinstalled and the stuffing box repacked. A small improvement as I can now get it into gear without it dying but still doesnt want to throttle up. I inspected the plugs and all appeared black soot covered. Would that be a weak spark indicator? My new coil I'd scheduled to arrive tomorrow. Again, thanks for the advice and feedback everyone.
Have you checked fuel cleanliness and pressure yet? A quick decant into a jar, and a $20 gauge, will take at least those two items out of the guesslist.
Reply With Quote
  #15   IP: 174.228.18.140
Old 01-16-2020, 10:37 AM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
I've been using clean fuel from a remote tank to troubleshoot. I haven't got a fuel pressure guage yet, but have verified the pump is pumping. I ran about a pint into a container to flush the lines and check the pump.
Reply With Quote
  #16   IP: 155.186.124.219
Old 01-16-2020, 11:08 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Catfish, sooty plugs are indicative of a week spark and/or poor timing, a further confirmation of this is all plugs being sooty. Could also be the choke is not open all the way.

Black oily thickly coated plugs are usually indicative of a bad cylinder and not usually found in all cylinders.

Don just released a good article on testing the coil, IE a good snappy 1/2" long spark is good. The plug wires need to be good, IE no cracks and have a good seal on the plugs. Also no cracks or tracks on the inside of the distributor cap.

What plugs are you using? Have you tried adjusting the idle yet. The idle circuit still works well into the 1500RPM range before the "hi speed (adj jet) is functioning. Get the idle working and then you can load the engine at a cruise speed or even against the dock lines to get the hi-speed adjusted for performance. Best done at cruise. If you are doing adjusting a vacuum gage is a help and valuable for tracking engine performance!!!

Dave Neptune
Reply With Quote
  #17   IP: 174.228.146.133
Old 01-18-2020, 08:09 PM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
Alright. Now she's running fine. Ran tied to the dock for 45 mins at all rpms and gear changes. I replaced the coil and that made a world of difference. I also noticed I had a ceramic resistor so I took it out. The coil i replaced had internal resistance as well so I'm not sure why the PO ran with it. I'm running champion rj12yc plugs gapped at .035.
Reply With Quote
  #18   IP: 24.152.132.140
Old 01-18-2020, 08:51 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
How much internal resistance? Where did you buy the coil?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #19   IP: 174.228.131.5
Old 01-19-2020, 02:05 PM
Catfish Catfish is offline
Senior Member
 
Join Date: Jan 2020
Posts: 26
Thanks: 22
Thanked 3 Times in 2 Posts
I replaced it with a MM coil. I'm not sure where the old one came from, but had the similar writing on the side "external resistance not required".
Reply With Quote
  #20   IP: 24.152.132.140
Old 01-19-2020, 02:39 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Good on ya. Sourcing from MMI will always get you the right parts for your A4.

The reason I asked is internal resistance coils typically come in three flavors: 3Ω, 1.5Ω and 3/4Ω and only one is suitable for our engine.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #21   IP: 24.19.229.135
Old 01-19-2020, 04:12 PM
Boat Boat is offline
Senior Member
 
Join Date: Aug 2014
Location: Kirkland, WA
Posts: 172
Thanks: 1
Thanked 14 Times in 13 Posts
fuel pump? pressure?
__________________
'69 Newport 30 MKI Hull #20
Reply With Quote
  #22   IP: 67.176.202.156
Old 01-19-2020, 05:25 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
electric Fuel pump from Moyer, pressure gauge with in line adaptor I am happy and use "Marshal" 0-15 psi. SS body, glass lens, liquid filled. About $25 on ebay
Reply With Quote
  #23   IP: 172.249.104.171
Old 02-04-2020, 11:49 PM
CamaroMan CamaroMan is offline
 
Join Date: Oct 2017
Location: San Pedro, CA
Posts: 42
Thanks: 3
Thanked 10 Times in 5 Posts
Quote:
Originally Posted by Sam View Post
electric Fuel pump from Moyer, pressure gauge with in line adaptor I am happy and use "Marshal" 0-15 psi. SS body, glass lens, liquid filled. About $25 on ebay
fyi the clear glass filters are not legal in the US - nothing glass/plastic allowed at all in the fuel system for inboard gas setups.

Either replace the inline fuel water/separator kits or something else - just a heads up..
Reply With Quote
  #24   IP: 67.176.202.156
Old 02-05-2020, 12:47 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
Good point on the "glass" used on fuel systems ie filters. I mentioned the glass lens on the fuel pressure gauge vs some cheaper ones that have plastic lenses that cloud up if some gas droplets find there way on them. The gauge is very useful, needs to be read so it has to be clear? Surprise to find it may not be totally legit??
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Just one more problem... engine stalls in forward gear infy Troubleshooting 15 06-23-2019 09:51 PM
A4 stalls in gear only Wavey Troubleshooting 49 08-22-2017 06:08 AM
idler gear conundrum azazzera Overhaul 2 07-02-2015 08:33 PM
rough running, put in gear and stalls. weremeer Troubleshooting 2 09-30-2009 03:56 PM


All times are GMT -4. The time now is 01:13 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved