Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 71.244.230.46
Old 08-19-2018, 07:18 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
Quick RPM Question

I've been doing a boatload of work (poor pun intended) on the boat and haven't been able to start it since the end of May. Ran into problems with the fuel pump (stuck valves) when I tried to start it and got through all of that. Now it is running great, but when I shift into either forward or reverse, it drags the engine speed way down and no matter how much throttle I apply, it barely gets above idle speed. I tried just putzing around the creek, but can't get above 1 1/2 knots and with current, I worry that I won't get back in. I thought it might be the stuffing box (the nut is loose enough to move with fingers, but I've never been able to get a drop of water to come out), but I can spin the prop shaft easily by hand.

My question is, can growth get thick enough in a few months (Chesapeake Bay) to keep the engine from being able to spin the prop adequately? I thought about tangled rope, but I would expect to feel that spinning the shaft by hand.

Thanks,
Steve
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #2   IP: 155.186.126.158
Old 08-19-2018, 08:46 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Steve, if the rpms rise a bit and no gain in speed is often growth. A Go-pro or a mask and a dip will tell you that.

If it is not the growth it could be sticking advance weights in the distributor an easy check just pop the cap and give the rotor a wiggle.

Once the above is confirmed time to look at fuel delivery. Do you have a fuel pressure gage? Do you have filers installed?

Dave Neptune
Reply With Quote
  #3   IP: 71.178.88.143
Old 08-19-2018, 09:49 PM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Quote:
Originally Posted by sdemore View Post
My question is, can growth get thick enough in a few months (Chesapeake Bay) to keep the engine from being able to spin the prop adequately? I thought about tangled rope, but I would expect to feel that spinning the shaft by hand.

Thanks,
Steve
Steve, yes. I have a guy that lives on his boat that works at the marina right next to me where I keep my boat. He says the growth in the Chesapeake this year is above normal.

I would recommend arranging a short haul if you can. I have pictures of my boat (July) with the beginnings of a reef if you are interested in seeing them.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #4   IP: 71.244.230.46
Old 08-19-2018, 10:49 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
I can see some growth on my rudder. It is a brown carpet looking growth, maybe 1/4" thick. I can only see one white spot that might be a barnacle, but I can't see the whole rudder. I've had people at the marina warn me about going into the bay right now, with the bacteria counts as high as they are.

Dave, the RPMs rise a few hundred at best and the boat vibrates from the drive train. I'll check the weights, but it doesn't seem like an engine problem. Fuel delivery was my problem last week (after the 3 months of sitting). The fuel pump had 2 stuck rubber valves in it. The entire fuel system was cleaned in the process of finding the stuck valves. I don't have a pressure gauge yet, but fuel flow is good now.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #5   IP: 216.99.180.222
Old 08-20-2018, 08:38 AM
tombrcc tombrcc is offline
Senior Member
 
Join Date: Jul 2016
Posts: 13
Thanks: 1
Thanked 1 Time in 1 Post
I see you're in Pasadena MD, I'm just across the river in Old Road Bay. I had my Catalina 30 pulled out this weekend for the exact same reason. Couldn't get RPM above 1000 and boat speed @ 2knts. Tons of barnacles on the prop and prop shaft. She was running a bit below hull speed 4 weeks ago, so the growth happened pretty fast.

Cleaned everything up and she's running along @ hull speed and able to get RPMs back up to 1800 no problem. Didn't go much over that as I now have a pretty good exhaust leak that needs to be repaired.

I tried diving rather than hauling out but visibility is less than 3 inches right now. They've released the Conowingo dam a good bit over the last few weeks with all the rain and the water is pretty murky.
Reply With Quote
  #6   IP: 138.207.175.58
Old 08-20-2018, 09:21 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
I'm due east of Steve, in Rock Hall. We pulled her about 10 days ago. Some slime, but the barnacles on the prop, the anodes, and the shaft were ferocious.

Someone should go to jail for what has flowed into the Bay from up north. And they fret over recreational boaters.....

We use a holding tank, period. Always have. Always will.

Bill
Reply With Quote
  #7   IP: 96.57.47.180
Old 08-23-2018, 10:28 AM
Skywalker's Avatar
Skywalker Skywalker is offline
 
Join Date: Jan 2012
Location: Stony Brook, NY
Posts: 621
Thanks: 0
Thanked 17 Times in 12 Posts
Been awhile since posted, but I've been visiting from time to time.

The weather pattern here on Long Island has really limited my use of the boat. This heat and humidity has come from a stuck system. Been horrendous.

Finally got to sail last night after a few weeks. Geez, the boat wouldn't move! Could barely get to 4 kts under power. A quick look from the dinghy changed my mind. I don't need a brush, I need a lawn mower!

Didn't get a good look at the prop, but I'm betting on some large barnacles, too.

Dive, Dive, Dive...
Reply With Quote
  #8   IP: 71.179.5.155
Old 08-23-2018, 07:34 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
For those of you who did a quick pull, clean, and relaunch, what is a good price? I haven't done it yet and my yard said that for a "short haul," it is $8.50 a foot, $255 for a 30' boat. Good/bad/average for this area?

Thanks,
Steve
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #9   IP: 138.207.175.58
Old 08-23-2018, 07:56 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
We paid $10.00 a foot.

Bill
Reply With Quote
The Following User Says Thank You to Administrator For This Useful Post:
sdemore (08-24-2018)
  #10   IP: 96.57.47.180
Old 08-24-2018, 08:40 AM
Skywalker's Avatar
Skywalker Skywalker is offline
 
Join Date: Jan 2012
Location: Stony Brook, NY
Posts: 621
Thanks: 0
Thanked 17 Times in 12 Posts
I dove last night. What a mess. An hour of scrubbing and I rediscovered a prop and a hull.

I short hauled last season after a winter of in water storage. Yard has to paint. The short haul and paint cost me over $800.
Reply With Quote
  #11   IP: 108.45.44.91
Old 08-27-2018, 09:14 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
I think Oak Harbor (right up the creek from you) charges $7.00/ft for a short haul.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #12   IP: 216.99.180.222
Old 08-27-2018, 11:04 AM
tombrcc tombrcc is offline
Senior Member
 
Join Date: Jul 2016
Posts: 13
Thanks: 1
Thanked 1 Time in 1 Post
$5/foot @ Old Bay Marina. Short haul and completely cleaned bottom, scrape and power wash. If you could make it across the river it may be worth the ~$100 savings.
Reply With Quote
The Following User Says Thank You to tombrcc For This Useful Post:
sdemore (08-27-2018)
  #13   IP: 71.179.5.155
Old 08-27-2018, 07:31 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
I contacted a diver this weekend and he said $3.50/foot. I asked about availability and haven't heard back yet.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #14   IP: 71.178.88.75
Old 08-29-2018, 10:44 PM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
I personally think $10/ft is a ripoff, but I understand they gotta pay their people, especially when the travel lift business is s-l-o-w in July...that is what I paid too. I would have never made it across any river..it was slow going to go from F dock to C dock at my marina where the travel lift is located.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #15   IP: 24.224.195.189
Old 08-30-2018, 05:07 AM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
One yacht club here charged $600 dollars to pull a 34 ft boat on a travel-lift for an out of water survey...survey not included. I thought that was steep.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
  #16   IP: 71.179.5.155
Old 08-30-2018, 06:48 AM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
I tried to get the diver out, but he was very unresponsive and finally said he couldn't get to it for a few weeks. I also saw a note about not cleaning ablative paint while in the water of the bay, so I gave up on him. Boat is being hauled and pressure washed tomorrow morning @$8.50/ft ($255). I hope this takes care of the problem.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #17   IP: 71.178.80.35
Old 08-31-2018, 12:38 AM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Steve, given what we have talked about in this thread, it seems reasonable. Still lots of money, but reasonable for the going rate.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #18   IP: 71.179.5.155
Old 08-31-2018, 02:08 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
Wow, what a difference. I couldn't even get the boat to move in a straight line t get out of the slip, let alone back up. Hauled it, scraped a boatload (pun intended) of crap off the bottom, pressure washed it, and put it back in. Runs and moves like normal now. The big surprise to me was, I spent weeks last year sanding down to bare fiberglass, barrier coating, and applying multiple coats of black ablative paint. I couldn't see any black paint today. I expected it to last longer than that.

__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #19   IP: 71.179.5.155
Old 08-31-2018, 02:12 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
Oh, and the other thing that shocked me, there was virtually no damage to the zinc after a year in the water. I expected there to be nothing remaining of it, but you could still read the writing on it.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
The Following User Says Thank You to sdemore For This Useful Post:
indigo (08-31-2018)
  #20   IP: 70.186.210.78
Old 08-31-2018, 02:50 PM
Tim's Avatar
Tim Tim is offline
Senior Member
 
Join Date: Jul 2005
Location: Gloucester, VA
Posts: 173
Thanks: 45
Thanked 51 Times in 35 Posts
That's way too many barnacles for one year. I wouldn't use that same bottom paint again. You probably should have re painted while you were out as you will probably have the same problem in a couple of months.
__________________
Pearson 10M
Gloucester, Va
Reply With Quote
  #21   IP: 71.179.5.155
Old 08-31-2018, 03:42 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
I'll pull it out in the spring to retreat it, but I'm seriously contemplating CopperCoat. It is much more expensive, but theoretically, I would never have this problem again or have to repaint again.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #22   IP: 138.207.175.58
Old 08-31-2018, 05:10 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Steve:

Did you use Petit Hydrocoat?

Bill
Reply With Quote
  #23   IP: 71.179.5.155
Old 08-31-2018, 07:53 PM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
No, I used TotalBoat Underdog from Jamestown Distributors. It was supposed to be high end stuff, but...

I am awaiting word from them on what may have gone wrong with it, or whether it is just junk. We figured out today, the boat has been in the water two weeks short of a year.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
  #24   IP: 108.45.44.91
Old 09-01-2018, 01:26 PM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by sdemore View Post
Wow, what a difference. I couldn't even get the boat to move in a straight line t get out of the slip, let alone back up. Hauled it, scraped a boatload (pun intended) of crap off the bottom, pressure washed it, and put it back in. Runs and moves like normal now. The big surprise to me was, I spent weeks last year sanding down to bare fiberglass, barrier coating, and applying multiple coats of black ablative paint. I couldn't see any black paint today. I expected it to last longer than that.
It HAS been a bad year for growth, but that's excessive. I used to use CPP Plus with good results until they started reducing the copper content (but not the price!)

Lately, I've been using Mar-Pro Super-B-Ablative. It's a copolymer paint. I put on two coats, and I usually get two years out of it, with a short haul and pressure wash in the off year.

Here's a photo of what it looked like this past spring after two years. Lot of slime, but not any hard growth on the hull.



Quote:
Originally Posted by sdemore View Post
Oh, and the other thing that shocked me, there was virtually no damage to the zinc after a year in the water. I expected there to be nothing remaining of it, but you could still read the writing on it.
This means either one of two things: Either your prop and shaft are stainless, so there's nothing much to protect, or your zinc is not in good electrical contact with the shaft. My zincs have a little spring-loaded copper ball on the inside to inure they remain in good electrical contact with the shaft after the corrosion has started. The shaft should be unpainted under the zincs and wire brushed shiny brite before installing them.
Attached Images
 
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #25   IP: 71.179.5.155
Old 09-02-2018, 06:19 AM
sdemore sdemore is offline
Senior Member
 
Join Date: Nov 2016
Location: Pasadena, MD
Posts: 230
Thanks: 84
Thanked 43 Times in 33 Posts
I sanded the area of the prop shaft where the zinc is, then taped it off before painting the shaft with the ablative paint. The zincs have the spring loaded balls in each side and I was told to smack both sides with a hammer to ensure good contact. The prop isn't stainless (brass or bronze colored), but I don't know what the shaft is made of. I didn't wire brush, but did sand it clean. I've heard that without power on the boat, the wear is less, but I don't know how true that is.
__________________
Steve Demore
S/V Doin' It Right
Pasadena, MD
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Quick question on running without a thermostat Bratina Cooling System 10 05-02-2018 10:36 PM
Quick water pump question robshepherd Cooling System 10 09-27-2013 06:45 PM
Quick Carb Question. yeahjohn Fuel System 6 04-30-2013 06:36 PM
Quick question team118 Troubleshooting 4 08-05-2012 04:31 PM
Quick ignition wiring question ILikeRust Ignition System 2 05-28-2011 05:57 PM


All times are GMT -4. The time now is 07:51 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved