Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 99.224.51.94
Old 07-11-2018, 07:47 PM
heinzb heinzb is offline
Member
 
Join Date: May 2018
Posts: 4
Thanks: 12
Thanked 0 Times in 0 Posts
Do I have a cracked block?

Over the years there have been many posts regarding the issue of having water in the oil.
I also have this problem.
I found the comments and suggestions very interesting and was hoping some would work for me.
I changed the oil several times but the problem did not go away.
I started to check areas mentioned in the forum to determine the cause. I began by doing a pressure test of the manifold and the block.
I tested the manifold first and found that it retained most of the pressure. It lost only about 10% over one hour.
Unfortunately I was not that lucky with the block.
Testing the block with the thermostat in the pressure was gone after half an hour. When I removed the thermostat the reading got a lot worse. It almost immediately lost all of the pressure. I double checked all the fittings to make sure there were no leaks.
Am I correct in presuming that I have a crack in the block?
I did not think it was the head since I changed the head gaskets last year. Perhaps I can remove the head again but how do I test the head for a crack?
Any suggestion/comments are greatly appreciated.
heinz
Reply With Quote
  #2   IP: 172.95.97.58
Old 07-12-2018, 11:42 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Heinze, when you get the head off many things will become apparent. Once the head is clean a close inspection with a magnifying glass may do the trick. If you find nothing in the block especially at the bottom of the cylinders where they sometimes rust through, look for a pin hole.

If the block is OK and you "SEE" nothing cracked on the head have it magnafluxed at an engine shop. Cracks often form around the alternator bracket!!!!

DO pressure check the manifold again!

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
heinzb (07-12-2018), Whippet (07-14-2018)
  #3   IP: 99.30.185.198
Old 07-12-2018, 12:10 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Heinze, Welcome aboard. When doing a pressure test of the block and head, it is a good idea to "not" include the water-pump in the plumbing setup. This is because you will be relying on the condition of the pump seals to hold pressure.
Tom
Reply With Quote
The Following 4 Users Say Thank You to thatch For This Useful Post:
Administrator (07-14-2018), Dave Neptune (07-12-2018), heinzb (07-12-2018), roadnsky (07-12-2018)
  #4   IP: 24.152.132.140
Old 07-12-2018, 06:24 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
When you retest have a spray bottle on hand filled with diluted liquid dish soap (3:1 water to soap). With the block/head under pressure spray the exterior with the solution. Any external leaks will develop soap bubbles at their source.

This helps resolve gasket and fitting leaks that could result in a poor casting integrity test.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
heinzb (07-13-2018)
  #5   IP: 69.255.26.55
Old 07-14-2018, 05:53 PM
Whippet's Avatar
Whippet Whippet is offline
Afourian MVP
 
Join Date: May 2012
Location: Toronto
Posts: 272
Thanks: 34
Thanked 18 Times in 16 Posts
Thanks MVPs

Quote:
Originally Posted by Dave Neptune View Post

If the block is OK and you "SEE" nothing cracked on the head have it magnafluxed at an engine shop. Cracks often form around the alternator bracket!!!!

Dave Neptune
Heinz is my neighbor at the yacht club - next dock over. He reached out to me a few weeks back (since he saw my posts on water in oil) and I went over to observe his engine in operation.

Actually ran pretty well - BUT darned interesting observation from Dave Neptune. Upon start up - water seeped out of head right at alternator bracket. Not a gush but a strong trickle.

What are odds that another shot at reinstalling head will fix it? Is Heinz looking at engine removal for further tests? (Heinz I will be in town in a few weeks and can give a hand if I can)
__________________
Steve
Etobicoke YC, C&C27
A4 #204381, 1980
Reply With Quote
The Following User Says Thank You to Whippet For This Useful Post:
heinzb (07-16-2018)
  #6   IP: 155.186.126.158
Old 07-14-2018, 06:48 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
If the water is seeping out of the stud it may be resealed however if it is leaking from a crack in the head just the head needs to be reset and gasketed.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
heinzb (07-16-2018)
  #7   IP: 108.45.44.91
Old 07-17-2018, 08:18 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by Dave Neptune View Post
If the water is seeping out of the stud it may be resealed however if it is leaking from a crack in the head just the head needs to be reset and gasketed.

Dave Neptune
Another victim of auto spellcheck? Shouldn't this read "replaced" ?
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #8   IP: 172.95.97.58
Old 07-17-2018, 12:01 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Edward, "and gasketed" for the gasket and reset for the process.

Dave Neptune
Reply With Quote
  #9   IP: 24.152.132.140
Old 07-17-2018, 08:52 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
however if it is leaking from a crack in the head just the head needs to be reset and gasketed.
I have read and reread your response Dave and laid back in respect of your forum status and many years of the best forum contributions ever but if there's leaking through a crack in the head, the head is done. Requires nothing short of replacement.

Maybe I misread or misunderstood something?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #10   IP: 69.255.26.55
Old 07-20-2018, 10:56 PM
Whippet's Avatar
Whippet Whippet is offline
Afourian MVP
 
Join Date: May 2012
Location: Toronto
Posts: 272
Thanks: 34
Thanked 18 Times in 16 Posts
more data

Hi Neil

I witnessed Heinz's leak with my own eyes. Wasnt coming from a crack in head per se -- but water seemed to be seeping right out of stud at alternator bracket. Can't be sure.

Heinz had replaced head gasket one year earlier. He didnt have compression in one cylinder - so some "expert mechanic" told him it was head gasket. Turns out it was just stuck valve.

So could this be as easy as another shot at gasket replacement? Assume the leak at stud would cause the failed pressure test?
__________________
Steve
Etobicoke YC, C&C27
A4 #204381, 1980
Reply With Quote
The Following User Says Thank You to Whippet For This Useful Post:
heinzb (07-21-2018)
  #11   IP: 24.152.132.140
Old 07-20-2018, 11:06 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I didn't have an opinion either way Steve, crack or no crack. However, the area of the head under the alternator bracket is notorious for cracks. Maybe another pressure test, soapy water spray bottle in hand with the alternator bracket removed and nuts torqued down? It would really be a good thing to know for sure where the pressure loss is before fixing anything.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 3 Users Say Thank You to ndutton For This Useful Post:
heinzb (07-21-2018), thatch (07-21-2018), Whippet (07-29-2018)
  #12   IP: 172.95.97.58
Old 07-24-2018, 12:53 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Red face OOPS

OOPS, missed a "not" in a sentence. Haven't been back to this thread.

Whippet~Heinz, because the "area" under the bracket is notorious for being loosened and retightened during the life of the head as well as transferring all of the stress of the alternator to said bracket I would only move forward by removing the head. The leak is most likely from the stud as it is a "flow" as cracks get wet along the crack and sort of weep water. In that same area under the bracket the gasket is somewhat compromised as there is a leak that probably happened due to the alternator loads and improper torqueing. Most any other stud on the head I would try resealing first.

Look very closely at the head for cracks with a good magnifying lens, if your not sure go for the magnaflux.

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
heinzb (07-25-2018), Whippet (07-29-2018)
  #13   IP: 99.224.51.94
Old 08-06-2018, 02:58 PM
heinzb heinzb is offline
Member
 
Join Date: May 2018
Posts: 4
Thanks: 12
Thanked 0 Times in 0 Posts
update

Thanks to all for providing me with tips and suggestions.
I have done some of the tests as suggested and the bottom line is that the block/head only holds pressure for about a half an hour. I did check the Oberdorfer water pump which appeared fine (I found out the hard way why the extended bolt was recommended for the lower slot). I also checked the studs which hold the bracket for the alternator for air leakage as Dave recommended. No leakage there.
I ran the engine afterwards for about 7-10 minutes and water is back in the oil. Based on comments regarding a cracked block and/or head, I am still hoping that it is something else that causes this but it looks like I am running out of areas to check.
I have not checked the plug by the valves for corrosion though, but what else should I check?
Thanks again for all your help especially to Steve who has not only provided me with moral support but also allowed me to use some of his tools.
Heinz
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Cracked Block From Old Head Bolts? Smuggli General Maintenance 3 07-07-2014 10:01 PM
Cracked Block Mark Millbauer General Interest 7 05-04-2010 06:58 AM
Can you have good compression and still have a cracked block? Baltimore Sailor Troubleshooting 4 05-05-2008 03:29 PM
Atomic 4 Cracked Block? cbanta Troubleshooting 9 09-27-2006 08:24 PM
Is a cracked block reparable? Michael L Troubleshooting 3 06-07-2005 08:24 AM


All times are GMT -4. The time now is 08:33 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved