Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Introductions

Reply
 
Thread Tools Display Modes
  #1   IP: 208.114.154.193
Old 07-03-2018, 08:35 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
New guy

Hi,

I have a 1976 C&C 27 with a late model A4. The motor has rwc and been run in salt water most of her life. I launched her last month and the distributor disintegrated. I was able to remove the shaft from the block with torches and tapping. I replaced it with a new electronic ignition distributor.

Then the water jacket side plate blew out due to corrosion. So a bought another A4 for parts mostly. Replaced cover and brass drain. Engine runs sweet now but water flow was low. Removed thermostat and flow was good. Replaced impeller and did a test run. After 40 minutes the engine shut down due to overheating. Lots of steam. I’m stumped.
Reply With Quote
  #2   IP: 32.211.28.40
Old 07-04-2018, 08:58 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
Terry,
First, welcome to the Forum. Hopefully you'll get some good advise here (if not from me, then from someone else - grin).
Overheating is not uncommon, particularly with raw water cooled engines. The blocks (and some other cast parts - not the side plate cover) are a high nickel cast iron and quite corrosion resistant. But even without corrosion, the raw water and heat will precipitate salt in the engine, tending to block things. A common place for blockage are the small passages between the block and the head by the valves.
Personally, I like running without a thermostat. Running the engine cool is not a cure-all, but I prefer the consequences to those from overheating. I'd also install a valve in the bypass line so you can control (or shut off) the bypass flow.
In your case, I suspect what happened is that removal of the thermostat and the new impeller caused increased flow - picking up all sorts of loose gunk inside the block and flushing it out. However, it just moved it somewhere else where it clogged things up. Could be anywhere downstream, but my first guess for a clog would be the outlet elbow on the manifold. Keep in mind, you should be able to blow through any component of the system with little resistance (including the block). The pieces are all connected by hoses. Disconnect them and try blowing through them individually - you'll quickly find the culprit (and perhaps some shaky hose clamps).
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
TerryB (07-12-2018)
  #3   IP: 24.224.194.51
Old 07-04-2018, 09:47 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
I agree with Al...

My thoughts on this one:

I would go right to exhaust manifold outlet. Remove the hose off the outlet closest to the hot exhaust section (the rear one) and try to put your finger in it. It may even look like there is water there so stick you little finger or something down in the hole and ensure it is clear. Another hint to this being the issue is if there was a smell of rubber. This would occur when the rubber on your exhaust hose heats up with the disproportionate amount of water and hot gases in the exhaust. If that turns out to be the case you will need to remove the exhaust manifold and clean it all out. Remove carb, choke attachement, throttle attachment. Disconnect hose off the end of the hot exhaust. If the hot exhaust breaks during removal it needed to be replaced anyway...again, not a major. Remove the 3 bolts holding the manifold...slide it to the side an inch or so to clear the studs and then move the whole manifold and hot exhaust forward and toward the cabin...keep it all together and pressure wash the manifold clean ...you could bring it to a rad shop either and have them clean it out...should be easy for DIY er though.

If that checks out double check the impeller. Some impellers don't fit correctly and leave a space between the cover plate and the impeller itself...there are cases where they were actually the wrong size. MMI has the right gear. It needs to be a tight fit. If there are wear score marks on the plate you can actually secure the plate and sand it with a course sand paper on a random orbital sander until flattened out...then put it back on with gasket or permatex and it will work better.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.

Last edited by Mo; 07-04-2018 at 09:54 PM.
Reply With Quote
The Following 2 Users Say Thank You to Mo For This Useful Post:
CajunSpike (07-05-2018), TerryB (07-12-2018)
  #4   IP: 24.15.42.104
Old 07-04-2018, 11:59 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
Might have put impellor in "backwards" and not sealing on pump backplate. Will look like pretty good flow but will not be enough to continuously cool engine. Impellor has tiny little dimples circular core that must be installed facing pump. Just a thought.
Reply With Quote
The Following User Says Thank You to Sam For This Useful Post:
TerryB (07-12-2018)
  #5   IP: 24.152.132.140
Old 07-05-2018, 12:35 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I did not read where you blocked the bypass when you removed the thermostat.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 4 Users Say Thank You to ndutton For This Useful Post:
Administrator (07-05-2018), joe_db (08-09-2018), Peter (07-05-2018), TerryB (07-12-2018)
  #6   IP: 142.162.48.81
Old 07-11-2018, 09:54 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Update

Thank you all for your input. So I flushed engine with two gallons of muriatic acid. First flush let soak for 15 minutes and then repeated before flushing with sea water. There were lots of brown water discharge. Ran engine at medium revs to flush but engine began to over heat again after 15 minutes.

So I took off hoses and checked the water lock muffler to see if it was,plugged. It was clear, looked new. The exhaust hose was in bad shape so I removed it. I will also replace the hose leading to the water lock muffler. Will check fitting exiting water manifold tomorrow. New exhaust hose arrives tomorrow afternoon.
I will also block water flow to thermostat bypass.

Will look at impeller to see if I put it in backwards. Never knew it only worked one way?
Reply With Quote
  #7   IP: 24.152.132.140
Old 07-11-2018, 10:05 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by TerryB View Post
I will also block water flow to thermostat bypass.
Without blocking the bypass you have no block cooling with the thermostat removed, no block cooling at all, only manifold.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 3 Users Say Thank You to ndutton For This Useful Post:
Administrator (07-12-2018), joe_db (08-09-2018), TerryB (07-12-2018)
  #8   IP: 67.176.202.26
Old 07-12-2018, 01:17 AM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
I think our west coast guru ndutton zeroed in on the real issue of your current overheating. Couple of thoughts - I have 1966 early model A4, Morgan 34, which has been in fresh water Lake Michigan its' whole life and came with a 140 F Dole thermostat. FYI decades ago I questioned this low operating temperature and it was explained to me that @ 140 F and lower salt does not precipitate out of sea water. Later on the late models the A4 engineers moved the limit to 160 F and changed the cooling flow etc. Think this when some salt blockages started to occur in the community.

My question to all is can an A4 really shut itself down from over heating without potentially damaging/warping valves, guides, springs, head gasket etc. I installed an OPSS but not any kind of temp alarm. When motoring I'm glancing at the gauges. Couple of times when some debris was picked up or impellor fin broke I shut it down, sailed in and then used the somewhat cooled A4 for the last minute of docking. An alarm would be reassuring and informative - any suggestions or guidance on brand or installation? Sorry if I ventured into a new topic but I thought it might be useful info. thx
Reply With Quote
The Following User Says Thank You to Sam For This Useful Post:
TerryB (07-12-2018)
  #9   IP: 24.53.89.131
Old 07-12-2018, 06:35 AM
Peter's Avatar
Peter Peter is offline
Afourian MVP
 
Join Date: Jul 2016
Location: Nova Scotia, Canada
Posts: 297
Thanks: 162
Thanked 140 Times in 101 Posts
Quote:
Originally Posted by Sam View Post
An alarm would be reassuring and informative - any suggestions or guidance on brand or installation?

https://moyermarine.com/product/the-...m-ktas_01_564/

Peter
Reply With Quote
The Following User Says Thank You to Peter For This Useful Post:
TerryB (07-12-2018)
  #10   IP: 71.222.3.150
Old 07-12-2018, 11:19 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Sam-
Please note that to use the EWDS, you'll need this base alarm as well.
The beauty of the EWDS system is that you can start out with just the basic alarm if you don't have the boat bucks to go the full monty.
And then add the full alarm to get the detailed warning (and comfort) the EWDS gives you.

Just give Ken (in parts) a call and he'll walk you thru it.


EDIT - I just realized... how ironic that the system Sam is looking for was invented by our "west coast guru".... Neil (ndutton)
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30

Last edited by roadnsky; 07-12-2018 at 11:30 AM. Reason: proper credit
Reply With Quote
  #11   IP: 142.162.48.81
Old 07-12-2018, 08:01 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Update 2

Well a little progress today. Then slapped back down to reality. I replaced the exhaust hose with a new one. I checked the impeller for dimples, there were none and te new one I put n a month ago is from MMI. I also put the thermostat back in.

I then installed a diverter valve after the tee on the engine cooling side jacket panel just before the thermostat to divert more cooling water into the engine. Checked for obstructions on the hot end of the coolant manifold and it was clear.
So I started h up and it ran fine but my temperature gauge is broken. Took it for a run and could touc the top of the thermostat the whole time. Seemed like was off to the races then the engine quit and would not restart. Smoke coming from back of engine area and coil was too hot to touch. So......what’s up now.

I did put a new distributor with electronic ignition and this is the first time I ran the engine over 30 minutes. Back to scratching my head.
Reply With Quote
  #12   IP: 24.152.132.140
Old 07-12-2018, 08:05 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by TerryB View Post
I did put a new distributor with electronic ignition and this is the first time I ran the engine over 30 minutes. Smoke coming from back of engine area and coil was too hot to touch. Back to scratching my head.
Please tell us about your coil:
Age
Brand
Internal resistance
Potting material
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #13   IP: 142.162.48.81
Old 07-12-2018, 08:10 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Coil

I will take it off tomorrow as it was too hot to touch and I was fed up and needed a beer lol. I just bought the boat and the learning curve is steep. Do coils need a resister?

I’m not even sure if it is the coil but need to start somewhere.
Reply With Quote
  #14   IP: 24.152.132.140
Old 07-12-2018, 08:17 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by TerryB View Post
Do coils need a resister? I’m not even sure if it is the coil but need to start somewhere.
With electronic ignition, some do. Give these threads a read this evening so you can return to the boat with new vigor:
http://www.moyermarineforum.com/foru...ead.php?t=5748 and the Cliff Notes version http://www.moyermarineforum.com/foru...ead.php?t=5845
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #15   IP: 205.174.171.14
Old 07-19-2018, 05:40 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Won’t start

Well changed coil. Turns over but won’t start. Was running fine. Lots of gas.
__________________
C&C 27
New Brunswick
Canada
Reply With Quote
  #16   IP: 50.233.106.125
Old 07-20-2018, 09:51 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by TerryB View Post
Well changed coil. Turns over but won’t start. Was running fine. Lots of gas.
As Neil asked...
What kind of coil?
Brand
Internal Resistance
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
  #17   IP: 208.114.154.194
Old 07-20-2018, 12:44 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Coil

From MMI. 3.4 ohms resistance. I’m wondering if I blew a fuse. I read there is a 20 amp fuse somewhere from the starter to the coil
__________________
C&C 27
New Brunswick
Canada
Reply With Quote
  #18   IP: 72.194.219.196
Old 07-20-2018, 03:29 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by TerryB View Post
Well changed coil. Turns over but won’t start. Was running fine. Lots of gas.
I think you are implying the engine won't start because of lack of spark?
What testing have you done to confirm this hypothesis?
Let's be sure of the problem before we start fixing.

TRUE GRIT
Reply With Quote
  #19   IP: 142.162.48.81
Old 07-22-2018, 01:59 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Won’t start

So I tested voltage tp the coil and it was fine. There was spark from coil wire, from the spark plug #1 as well. I looked at gas vent, it was okay. There was fuel leading up to carb and manual pump was free. Tried starter fluid with spark arrestor removed and still no start.
__________________
C&C 27
New Brunswick
Canada
Reply With Quote
  #20   IP: 24.152.132.140
Old 07-22-2018, 02:17 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Starter fluid and no fire indicates no spark, spark at the wrong time or no compression. Let's find out which it is.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 2 Users Say Thank You to ndutton For This Useful Post:
sastanley (07-24-2018), TerryB (07-22-2018)
  #21   IP: 156.57.113.226
Old 08-09-2018, 07:54 AM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Solved

Well it took me awhile to figure this out but I was able to resolve all my engine woes. The boat was new to me and the initial problem was overheating. In summary I replaced the impeller, cooling hoses, water jacket side plate and installed a diverted valve just after the t junction. Don Moyer bless his heart suggested I replace the exhaust hose leading to the transom which I did. I also acid flushed engine and my overheating engine was fixed.

Then my coil died. So I replaced my coil. Spark but the engine refused to start. Checked fuel flow to carb was fine. Flow to filter was fine. Lots of fuel. So I went back to my spark and tested each plug. Good spark. I pored gas through each spark plug hole. No start. So gas wasn’t my issue. Then I looked at how my coil was wired and realized it was wrong. Switched one wire leading to alternator and it jumped to life. Such an easy fix if you know what you’re doing. I’m still learning but grateful to everyone of you who helped me through this.
__________________
C&C 27
New Brunswick
Canada
Reply With Quote
The Following 2 Users Say Thank You to TerryB For This Useful Post:
Dave Neptune (08-11-2018), Tim (08-09-2018)
  #22   IP: 173.67.178.179
Old 08-09-2018, 09:07 AM
Don Moyer's Avatar
Don Moyer Don Moyer is offline
 
Join Date: Oct 2004
Posts: 2,811
Thanks: 0
Thanked 183 Times in 124 Posts
Coil wire wrong

Terry, can we assume that your field flashing wire was connected to the negative terminal of your coil rather than the positive terminal? The field flashing wire is the smaller gauge wire of the two wires normally coming from the alternator. Don
Reply With Quote
  #23   IP: 72.194.219.196
Old 08-09-2018, 11:05 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by Don Moyer View Post
Terry, can we assume that your field flashing wire was connected to the negative terminal of your coil rather than the positive terminal? The field flashing wire is the smaller gauge wire of the two wires normally coming from the alternator. Don
Been down this road myself. Now, before I install a new coil, I put a dot of white paint at the negative post of the coil. On my boat it is hard to see the + and - markings on the coil connections when it is installed or even when installing it.

TRUE GRIT
Reply With Quote
  #24   IP: 142.169.78.147
Old 08-09-2018, 08:47 PM
TerryB's Avatar
TerryB TerryB is offline
Frequent Contributor
 
Join Date: Jun 2018
Posts: 9
Thanks: 10
Thanked 2 Times in 1 Post
Coil Wiring

Don, the way I have the coil wired now is three wires to the positive terminal of the coil. They come from the ignition switch, the distributor and the alternator. The only wire in the negative side of the coil returns to the distributor.
__________________
C&C 27
New Brunswick
Canada
Reply With Quote
  #25   IP: 173.67.178.179
Old 08-10-2018, 05:35 AM
Don Moyer's Avatar
Don Moyer Don Moyer is offline
 
Join Date: Oct 2004
Posts: 2,811
Thanks: 0
Thanked 183 Times in 124 Posts
Coil wires

Terry, assuming that you have an Ignitor electronic ignition system, make sure it's the red wire from the distributor that connects to the positive of the coil and the black wire to the negative. Don
Reply With Quote
The Following User Says Thank You to Don Moyer For This Useful Post:
TerryB (08-10-2018)
Reply

Tags
coil failure, cooling water stops, engine dies, over-heating

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:07 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved