Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Fuel System

Reply
 
Thread Tools Display Modes
  #1   IP: 73.53.80.228
Old 06-30-2016, 09:33 PM
Cityhix Cityhix is offline
Senior Member
 
Join Date: Jun 2016
Posts: 13
Thanks: 8
Thanked 0 Times in 0 Posts
New A4 owner, fuel delivery problem?

Hello. I've done a fair bit of reading here and on the Moyer site regarding fuel delivery problems. I have some ideas about where I should go but thought I would throw out a query.

-Late model A4 in a '71 Ericson 29.
-Facet electronic fuel pump installed more than ten years ago.
-Fuel tank is above the motor and approx 5-6 feet away.
-New carburetor installed less than ten years ago.
-Last tune up done about one year ago.
-Main fuel filter changed within the last four months.
-Failure to turn on the raw water intake resulted in overheating (240?) last weekend.

Problem:

Engine starts easily and idles beautifully. Motoring out of the harbor this week, the engine started to sound like it was faltering. The temp appeared to be fluctuating (can't recall the high/low). Motor finally stopped but restarted immediately. We went sailing and had to restart several times on our way back into the harbor. At the dock, idling was great but while tied up and in forward the motor will run great up to approximately 1400 RPM and then quit abruptly. Pulling the choke out will keep it running for another ten seconds or so.

I intend to go through the whole system up to the carburetor, replacing the inline filter, fuel lines, valves possibly, assure that the main filter is properly seated and possibly add a priming bulb. I've read of the possibility of pulling air into the system from a tiny leak. I should probably add an inline fuel gauge to make sure that we are getting good push from the fuel pump too.

I know not an easy answer but thanks for any insight!
Reply With Quote
  #2   IP: 76.179.157.47
Old 07-01-2016, 07:41 AM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
Welcome to the Forum!

Everything you said makes sense, but let me add a little:

Depending on how long you ran hot and dry, your water pump impeller is suspect at best.

No priming bulbs, please. At least not for permanent installation. They are not rated/safe for interior machinery spaces.

A fuel pressure gauge is invaluable for troubleshooting. $15 or so at YLFAPS (your local friendly auto parts store).

Do you have an OPSS in the fuel pump circuit?
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
The Following User Says Thank You to BunnyPlanet169 For This Useful Post:
Cityhix (07-04-2016)
  #3   IP: 32.211.28.40
Old 07-01-2016, 09:33 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
Cityhix,
I'm going to muddy your waters a bit and suggest an electrical problem - possibly the ignition switch. Intermittent high resistance in the switch (or it's wiring) will give you problems running and also make the gauges go nuts. A jumper from battery + to coil + will bypass the switch, but is only a temporary measure for diagnostics.
As for the carb, it's at the end of the fuel system and all flows to the carb - gas, water, and krap. Yeah, the filters are supposed to let only the good stuff through, but I've learned to carry a spare carb. I've lost count of the times I've had the float valve hang open or had the main jet clog - even with a Racor primary and an inline secondary filter. BTW, carb changes are quicker if you go with studs in the carb and nuts over the manifold flange.
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
Cityhix (07-04-2016)
  #4   IP: 50.189.109.105
Old 07-01-2016, 10:02 PM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
Quote:
Originally Posted by Al Schober View Post
BTW, carb changes are quicker if you go with studs in the carb and nuts over the manifold flange.
Thusly.

http://www.moyermarine.com/forums/al...pictureid=1881
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
The Following User Says Thank You to BunnyPlanet169 For This Useful Post:
Cityhix (07-04-2016)
  #5   IP: 68.108.255.88
Old 07-02-2016, 02:11 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
As Far As The Variable Temp Reading Go......

Have a look see at the water pump impeller to see if any of the veins are broken off. If there are any pieces of the impeller in the cooling system they may be acting as a flapper valve to the water flow. This is sort of far out but still possible. Are you RWC or FWC?

TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
Cityhix (07-04-2016)
  #6   IP: 73.53.80.228
Old 07-03-2016, 01:22 AM
Cityhix Cityhix is offline
Senior Member
 
Join Date: Jun 2016
Posts: 13
Thanks: 8
Thanked 0 Times in 0 Posts
First, thanks for all suggestions.

I did swap in a new raw water impeller today. The old one was definitely looking tired.

Replaced the plugs and added a dash of Marvel into each cylinder. That made me feel like the neighborhood polluter for sure! Sprayed some carb cleaner down the intake. Replaced the inline fuel filter between the fuel pump and carb.

I also found a blown 10a fuse in a lead to the oil pressure sender. The fuel pump is supplied with power from the same unit but from a terminal on the aft side of the sender (not the lead that had the blown fuse). Not sure if this had anything to do with my problem but it seems to be running properly now.

I was rescued by a buddy who showed up today with a cold beverage. After I had everything back together, the motor kept quitting after shorter and shorter intervals. I was baffled and about to throw in the towel when he poked his head in and noticed that I had shut off the valve at the fuel tank. I was burning through the fuel in the filter. He switched it back on and all seems well.

Fun day on the boat today!
Reply With Quote
  #7   IP: 50.189.109.105
Old 07-03-2016, 08:15 AM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
The blown fuse is everything.

The circuit is coil + to the ( EDIT usually the fuse ) to the OPSS and then to the fuel pump. The fuel pump then supplies the ground via mounting. The OPSS is a low pressure safety switch that requires minimal pressure to close, supplying power to the fuel pump only when the ignition switch is on, and the engine creating oil pressure ( I.E. Running).

Bring a spare - if the fuse blows again, you've got a problem in that circuit.
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169

Last edited by BunnyPlanet169; 07-03-2016 at 10:31 AM.
Reply With Quote
The Following User Says Thank You to BunnyPlanet169 For This Useful Post:
Cityhix (07-04-2016)
  #8   IP: 107.0.6.244
Old 07-03-2016, 09:33 AM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking Questions come to mind

The circuit itself is a problem. The ignition circuit should be independent of the fuel pump. I recommend separate OPSS for both. If you are blowing a 10 amp fuse with both ignition and fuel pump that raises another question. Who is getting all the juice? Or is there another user in there? Are you in effect using a messy circuit as a coil resister?
Reply With Quote
  #9   IP: 68.108.255.88
Old 07-03-2016, 10:12 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
10 amps is a lot of electricity. My bet is something was\is grounded somewhere. Maybe the fuel pump, maybe the wiring.
If you keep not rembering to turn the fuel shut off valve on put the key on the valve when you shut it off.

TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
Cityhix (07-04-2016)
  #10   IP: 24.152.132.65
Old 07-03-2016, 11:01 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I load up my ignition circuit pretty heavily - without a single issue by the way - and still remain under 80% of the 10 amp fuse value.

Ignition load = 3.4 amps
Alternator excite = 0 amps (single wire self excite)
Facet fuel pump = 1.6 amps
Johnson CM30P7-1 coolant pump = 2.2 amps
EWDS = 0 amps (by design, no draw unless triggered)

Total ignition circuit load = 7.2 amps

Point being, even with considerable loads on the ignition circuit a 10 amp fuse is fine under normal conditions. That your fuse was blown indicates a circuit or device problem as mentioned by others.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Cityhix (07-04-2016)
  #11   IP: 73.53.80.228
Old 07-04-2016, 10:34 AM
Cityhix Cityhix is offline
Senior Member
 
Join Date: Jun 2016
Posts: 13
Thanks: 8
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by BunnyPlanet169 View Post
The blown fuse is everything.

The circuit is coil + to the ( EDIT usually the fuse ) to the OPSS and then to the fuel pump. The fuel pump then supplies the ground via mounting. The OPSS is a low pressure safety switch that requires minimal pressure to close, supplying power to the fuel pump only when the ignition switch is on, and the engine creating oil pressure ( I.E. Running).

Bring a spare - if the fuse blows again, you've got a problem in that circuit.
OK. I think I understand. But I am confused why I was able to run the motor at all with power supply to the fuel pump interrupted by the blown fuse. Will fuel flow through the pump passively? The fuel tank is located somewhat higher than the carburetor. Maybe gravity is my friend?

Cityhix
Reply With Quote
  #12   IP: 24.152.132.65
Old 07-04-2016, 11:08 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
You are exactly correct. The pump will pass fuel on a gravity feed but the flow won't keep up with the running engine's demands. This is not necessarily a good thing when the boat is sitting idle. If you don't have one you might consider a positive fuel shut off valve immediately ahead of the carburetor.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #13   IP: 50.189.109.105
Old 07-04-2016, 10:07 PM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
FWIW - looked at mine today - it's only 5A and I've never had it go....
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fuel line and carb fouling mysteries solved! wattsr Fuel System 5 06-04-2012 11:33 PM
Fuel pump was the problem! mlucas Ignition System 5 08-24-2011 08:39 PM
Engine won't start - fuel delivery problem gary gerber Fuel System 7 05-24-2009 05:09 PM
Do I Have a fuel Problem Ydel Troubleshooting 2 11-27-2004 02:53 AM


All times are GMT -4. The time now is 05:57 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved