Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Fuel System

Reply
 
Thread Tools Display Modes
  #1   IP: 192.186.122.174
Old 03-07-2019, 02:48 PM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Idle & RPM

So, when one leans out the idle mixture, would that affect the rpm everything else being the same?
__________________
Greg
1975 Alberg 30

Last edited by GregH; 03-11-2019 at 08:44 AM.
Reply With Quote
  #2   IP: 97.93.70.7
Old 03-07-2019, 06:17 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
It can and should have a "slight" influence in RPM's until it begins to shudder to a stop. Maybe +/- 50 RPM.

Dave Neptune
Reply With Quote
  #3   IP: 192.186.122.174
Old 03-11-2019, 08:44 AM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
OK, not as much as I was thinking.
__________________
Greg
1975 Alberg 30
Reply With Quote
  #4   IP: 97.93.70.7
Old 03-11-2019, 11:44 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Red face Many things perhaps

Greg, you may have there issues as the +/- I gave you are for a good tune as far as all else is concerned. Timing, sticky advance weights, float level, any kind of a vacuum leak and the carb internal seals all can cause adverse idle conditions which will render proper adjustment of the idle mix most difficult and almost impossible to get set.

What is the state of tune from above? Any recent work on the carb? Did you check for any vacuum leaks?

Can you describe what has been done and what is currently being tried?

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
Administrator (03-11-2019), thatch (03-11-2019)
  #5   IP: 72.194.222.152
Old 03-11-2019, 05:25 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
After you lean the idle you might also notice:

Cleaner running spark plugs.

Hard starts, especially when the engine cold. If this happens check to be sure the choke is closing all the way.

TRUE GRIT
Reply With Quote
  #6   IP: 192.186.122.174
Old 05-07-2019, 04:08 PM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Sorry folks, seemed to have missed seeing the replies here!

I'll get back to you shortly as I hope to get the engine spring commissioned this coming weekend. And then I can report on the current settings.
__________________
Greg
1975 Alberg 30
Reply With Quote
  #7   IP: 47.16.178.29
Old 05-07-2019, 08:00 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I am looking into this issue as well. I've noticed last season that my idle RPM was a bit high (1000+ rather than 800). This season the engine is running a bit rough at idle, which may still be somewhat due to water in oil issue that I had earlier. I am primarily looking into possible sources of air leaks in the carburetor. But I also came across some older posts by Dave Neptune where it was suggested that RJ12C gap should be close to 0.040 with EI. Default gap for RJ12C is 0.03. I think I saw Dave say that increasing gap would improve engine running at idle speed. Is this the case?
Reply With Quote
  #8   IP: 36.92.31.163
Old 05-07-2019, 11:05 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by Wisakedjack View Post
...I think I saw Dave say that increasing gap would improve engine running at idle speed. Is this the case?
I'll take the liberty of answering since I have saved a few quotes from Dave on this topic...

"I have been gapping my plugs at .038~040" (larger gap acts a bit like a hotter plug)
...gap the plugs to around .040, this will help the idle by raising the temp of the plugs tip a bit and creates a better burn for a cleaner plug."

"Note take advantage of the EI by opening up the plug gap a bit .040/.045 will work fine on the top end and idle much smoother too."
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following User Says Thank You to roadnsky For This Useful Post:
Wisakedjack (05-07-2019)
  #9   IP: 97.93.70.7
Old 05-08-2019, 10:58 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Lightbulb Extra gap clarity

The additional gap will raise only the temp of the tip's as there will be a bit better fire (burn) at low idle speeds. It takes a bit more energy to jump the gap and that additional energy is what helps.

With a std ignition .035 is very doable as the RPM's and combustion pressures are not high enough to bother the plugs firing at higher RPM's that an A-4 will never see.

With an EI I feel safe running the gap all the way to .040" and did so on my boat for over 30 years with stock plugs and poor compression!!!

You will also hear that a tighter gap will increase horse power. This is only true with older "std ignitions" and a hi-performance engine. These engines develop enough pressure that makes it harder for the spark to jump the gap and a bit tighter would allow the spark to jump and all was well except that idle quality would be affected. Now with the super hot ignitions on everything we see gaps of over .070" and plug life of a hundred thousand miles or a whole lot of hours.

In my view an EI is a must as it is far more reliable and simpler to diagnose than points and condenser. Also with an EI your dwell will be fixed unlike with points. And old distributors are no good for setting the points by gap as the cam they run on is worn. This is why you see so often on this site the question "what is the dwell?".

Dave Neptune
Reply With Quote
The Following 3 Users Say Thank You to Dave Neptune For This Useful Post:
GregH (05-09-2019), Tim (05-08-2019), Wisakedjack (05-08-2019)
  #10   IP: 73.44.129.106
Old 05-09-2019, 06:57 PM
Sam Sam is online now
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
Dave, just thinking out loud here. We have a short season here in Chicago and I have a clean good running virgin 1966 A4 w/ Prestolite distributor w/points and some minor dark fouling on plugs by season end. If I assume my distributor cam might be worn a bit can I approximate a better "dwell" by tightening the point gap slightly from the .020 [compensating for cam wear]. I still time the engine using the " N Dutton" method by rotating the distributor to enhanced rpm at cruising speed then back off a "tick". Not very scientific but a little better than what I used to do back in the day with my first car, 1963 Chevy Corvair, by opening the door and adjusting the timing until the door stopped vibrating. [Apologize for diverting the thread. Generally on things if I am 90% or so on target it is usually good enough]
Reply With Quote
  #11   IP: 97.93.70.7
Old 05-09-2019, 07:58 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Sam, a dwell meter is cheap on line. It can be used to confirm dwell after setting the points. The meter will let you know if you need to open or close the gap. Usually a tighter gap is needed to compensate for wear.

For not much more than the dwell meter you could convert to the EI and use you saved maintenance time for liquid bread or dialing in the tune.

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
Administrator (05-09-2019), Sam (05-10-2019)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Good Problem Jimmy General Interest 6 05-14-2012 10:04 PM
Erratic Engine Speed Unregistered Troubleshooting 3 01-24-2012 10:12 PM
Issues at idle TomG Fuel System 39 10-19-2011 06:31 PM
Suspected Idle Circuit Blockage - causing idle problems dman535 Fuel System 15 07-19-2009 07:49 AM
Idle RPM tartan30cirrus General Maintenance 6 05-17-2005 06:58 PM


All times are GMT -4. The time now is 06:46 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved