Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 108.7.215.73
Old 06-30-2020, 05:34 PM
Tartan30guy Tartan30guy is offline
Member
 
Join Date: Jun 2020
Posts: 3
Thanks: 4
Thanked 0 Times in 0 Posts
Stalls out under load

Hi all. I have a A4 that ran great on the hard but is sputtering and dying out when I try to increase RPMs in FWD now that I'm in the water. Out of gear when i increase RPMs it kind of hesitates a bit on the way up but gets there. In FWD I can get the RPMs up a bit but when I apply more throttle RPMs drop, the engine sputters then quits completely. However, with the choke pulled out I can increase RPMs right up but it just doesn't sound right when I do that.

Thre A4 is a late 90s (from what I'm told) Moyer marine A4. Electronic ignition. I've just done a refit of my Tartan 30, and part of that was a new fuel tank, new lines and filter, oil changed, new plugs. I've cleaned the glass bowl out on the carb and I've blasted carb cleaner into the carb after taking off the flame arrestor, but I continue to have the problem. The hour meter (which works) shows 486 total hours. Not sure if that represents actual hours since install.

I'm thinking of trying to adjust the lean/rich mix screw as if the choke is pulled I can rev up ok, which tells me I'm to lean right now (right??) but before I did that I thought I'd join here at Moyer and ask for help on the issue.

I look forward to hearing your opinions. Thanks!
Reply With Quote
  #2   IP: 69.251.79.112
Old 07-01-2020, 10:07 AM
scratchee scratchee is offline
Senior Member
 
Join Date: Feb 2020
Posts: 97
Thanks: 27
Thanked 44 Times in 28 Posts
Have you seen this carb troubleshooting video from Moyer? I've cued it up to a point that may address your problem, but you should watch the whole thing anyway.

https://youtu.be/kHuemGC_PHA?t=166
Reply With Quote
The Following User Says Thank You to scratchee For This Useful Post:
Tartan30guy (07-01-2020)
  #3   IP: 67.169.215.221
Old 07-01-2020, 10:27 AM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
... and welcome to the forum.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
Tartan30guy (07-01-2020)
  #4   IP: 72.69.36.126
Old 07-01-2020, 11:11 AM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Potential cause 1: carb issue, as discussed in the video
Potential cause 2: blocked exhaust
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
Tartan30guy (07-01-2020)
  #5   IP: 38.27.109.137
Old 07-01-2020, 12:10 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Only under load?

Bill
Reply With Quote
  #6   IP: 172.58.219.231
Old 07-01-2020, 05:35 PM
Tartan30guy Tartan30guy is offline
Member
 
Join Date: Jun 2020
Posts: 3
Thanks: 4
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by tenders View Post
Potential cause 1: carb issue, as discussed in the video
Potential cause 2: blocked exhaust
So let's talk about exhaust blockage. Right now, the A4 exhaust is exactly what I'd expect; good water flow and exhaust gasses coming out. When I increase RPM, the water flow and exhaust gasses increase as well. With this in mind, I'm not thinking the exhaust is an issue. Am I missing something? Thank you
Reply With Quote
  #7   IP: 108.7.215.73
Old 07-01-2020, 05:40 PM
Tartan30guy Tartan30guy is offline
Member
 
Join Date: Jun 2020
Posts: 3
Thanks: 4
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by Administrator View Post
Only under load?

Bill
Well not completely true. In neutral, when I apply throttle, the RPMs increase but not as smoothly as would expect, it struggles a bit with "hiccups" as I increase RPMs.

Under load (in forward) when I apply throttle I get a slight increase in RPMs before the engine sputters and quits.

I'm thinking there is a blockage in the carb and I need to remove clean it.

Thoughts? Thanks for your input, Dave
Reply With Quote
  #8   IP: 165.225.38.121
Old 07-01-2020, 07:10 PM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
Quote:
Originally Posted by Tartan30guy View Post
Well not completely true. In neutral, when I apply throttle, the RPMs increase but not as smoothly as would expect, it struggles a bit with "hiccups" as I increase RPMs.

Under load (in forward) when I apply throttle I get a slight increase in RPMs before the engine sputters and quits.

I'm thinking there is a blockage in the carb and I need to remove clean it.

Thoughts? Thanks for your input, Dave
question: your engine should revs up very quickly without load (without "hiccups") "almost explosively" would say Mr Don M. Does it do that when not in gear? If yes, I would recommend to check the carburetor of course like everybody else, but would recommend to check first that the shaft turns "freely" by hand. If you have a piece of line entangled in your prop shaft, that could explain some of your issues...
If it does not rev up quickly when in "neutral", that excludes the shaft line, and would point toward your carburetor (assuming your exhaust path is clear (exhaust manifold + exhaust pipe etc...))
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
The Following User Says Thank You to Surcouf For This Useful Post:
Tartan30guy (07-01-2020)
  #9   IP: 24.53.89.131
Old 07-01-2020, 08:20 PM
Peter's Avatar
Peter Peter is offline
Afourian MVP
 
Join Date: Jul 2016
Location: Nova Scotia, Canada
Posts: 297
Thanks: 162
Thanked 140 Times in 101 Posts
Fuel pressure gauge might be a useful diagnostic tool here.

I had a similar situation where engine would only run with choke. Fuel pressure was dodgy.

If you have good fuel pressure it is a carb issue. If not, look upstream.

Peter
Reply With Quote
The Following User Says Thank You to Peter For This Useful Post:
Surcouf (07-01-2020)
  #10   IP: 72.69.36.126
Old 07-03-2020, 03:50 AM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Quote:
Originally Posted by Tartan30guy View Post
So let's talk about exhaust blockage. Right now, the A4 exhaust is exactly what I'd expect; good water flow and exhaust gasses coming out. When I increase RPM, the water flow and exhaust gasses increase as well. With this in mind, I'm not thinking the exhaust is an issue. Am I missing something? Thank you
It is possible to have a partially blocked exhaust that allows some water and gas out but not enough to permit the engine to exhale properly and deliver proper power. This can happen from sediment/scale in the manifold or from a collapsed ply in the rubber exhaust hose, even though the outside of the hose looks fine.

You detect this by disconnecting the hose and running the engine briefly to see if the power response improves.

I agree, the carb is more likely the source of the problem but isn’t necessarily the only cause of the symptoms you’re describing.
Reply With Quote
  #11   IP: 71.222.36.208
Old 07-03-2020, 10:13 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
To add to Tenders comment...
another quick (and simple) test for exhaust blockage is to remove one spark plug at a time while the engine is running and see if you notice any change.
An improvement while running on only 3 cylinders would suggest a closer look at your exhaust.

EDIT: I found THIS in the Tech Tips if you want to read more...
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30

Last edited by roadnsky; 07-03-2020 at 10:29 AM.
Reply With Quote
  #12   IP: 100.36.65.17
Old 07-03-2020, 01:53 PM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by Tartan30guy View Post
...and I've blasted carb cleaner into the carb after taking off the flame arrestor, but I continue to have the problem.
...
I look forward to hearing your opinions. Thanks!
In my experience, modern carb cleaners do not have the crud-cutting capabilities of those in my youth (which would instantly dissolve all forms of crud, and most plastics!). I find it is necessary to disassemble the carb and physically ream out every orifice with a small wire in order to insure they're clear. Just spraying isn't enough. Even an almost microscopic particle or layer of gunk can drastically affect the carb.

The wire from the center of a bread tie is just the right size. I've also had good luck with an acetylene welder's tip cleaner. In addition to the main jet and the idle jet, be sure to get the two small holes that straddle the throttle plate in the closed position.

Your case does sound like a failing transition from the idle jet to the main jet, so be sure to pay special attention to the main jet.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
The Following 2 Users Say Thank You to edwardc For This Useful Post:
capnward (07-05-2020), Dave Neptune (07-03-2020)
  #13   IP: 69.251.79.112
Old 07-03-2020, 07:39 PM
scratchee scratchee is offline
Senior Member
 
Join Date: Feb 2020
Posts: 97
Thanks: 27
Thanked 44 Times in 28 Posts
Quote:
Originally Posted by edwardc View Post
... I find it is necessary to disassemble the carb and physically ream out every orifice with a small wire in order to insure they're clear. Just spraying isn't enough.
The video shows how to access the main jet directly without disassembling. Might get lucky, if that is indeed the problem.
Reply With Quote
  #14   IP: 47.142.132.120
Old 07-04-2020, 01:09 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
T 30
Is there a "polishing filter" between the fuel pump and the carburetor? If not this would be a good time to add one.
The polishing filter will keep the little bits of crud out of the carburetor.

ex TRUE GRIT
Reply With Quote
  #15   IP: 142.134.226.131
Old 07-04-2020, 05:50 AM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
Take a few minutes and check your compression. I worked on one a number of years back and the guy had bought a new carb etc, then changed prop...his issue was lose of compression and it was early in the year, just after winter layup..... It would run, would move in reverse, but when put in forward stall.

Just a thought in your troubleshooting process.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Engine erevs well no load, will only do 900rpm in gear Bryan Howell Troubleshooting 25 06-12-2017 08:57 PM
Engine runs rough at higher RPM's under load capnward Troubleshooting 7 09-30-2014 05:01 PM
Engine stalls under load STAHOE97 Troubleshooting 5 06-03-2010 07:32 AM
Stalls Under Load Bakerd Troubleshooting 2 10-01-2007 09:00 AM
Low RPM's Under Load Jeremy Thompson Troubleshooting 7 11-18-2005 06:10 PM


All times are GMT -4. The time now is 06:02 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved