#1
IP: 73.234.59.26
|
||||
|
||||
Overheating due to coolant loss
I have searched the threads and have some ideas on what to look for but posting this so that others and myself could go through some learning of my process.
First off, this has been really frustrating! I have a brand new engine rebuild do at a local machine shop. New head, new exhaust manifold, new pistons, rings, bearings, heat exchanger, etc. Been through a whole mess of things for since launching my boat with this new engine. Most recently, I am struggling with milky oil and me putting constant antifreeze into the system. Obviously, the antifreeze is getting into the oil at this point. I now have to figure out how/why... I know the typical steps but let me share some of my symptoms: 1. Engine is hard to start. Takes a lot of cranking before running 2. Plugs look black if taken out 3. Runs great after turning on but I have to keep putting af into heat exchanger due to leak Obvious next steps will have to be pressure tests. Could be my water pump...but doubt it since I have the Oberdorfer with the weep hole...but it just seems like the leak is substantial...like I have to fill heat exchanger every 10 mins or it runs dry... Going to boat today but super frustrated at this point...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) Last edited by southcoasting; 08-12-2020 at 08:09 AM. |
#2
IP: 137.103.82.227
|
||||
|
||||
Yikes
Pressure test and compression test stat! The best thing to find would be a head gasket needing replacement or maybe a hole in the manifold. |
#3
IP: 207.32.168.30
|
||||
|
||||
If your HX is draining in 10 minutes, that water has to be going somewhere, like into your crankcase. When it is running, check to see if your water pump is leaking out of the weep hole underneath the seals. I had mine leak so bad that it forced water into the crankcase through the accessory drive, as well as out the weep hole. The engine ran anyway, but overheated due to reduced coolant flow, as water was going other places besides the water jacket. The seals were shot. The bearings and shaft were replaced as well. If your local shop worked on the water pump, they may have installed the seals inside out, a common mistake. The engine being hard to start could be a different problem.
|
The Following User Says Thank You to capnward For This Useful Post: | ||
TimBSmith (09-11-2020) |
#4
IP: 155.186.124.219
|
|||
|
|||
First, how much is the oil level going up? It should be about as much as you are adding coolant.
The first check I would do is a compression check to check the head-gasket. If the compression check does not show a low cylinder it will be time for a leak-down test of the manifold and block. First check the manifold as it is easy to isolate then the block. Since you stated that all the plugs are black I would suspect the manifold as the culprit. Dave Neptune |
#5
IP: 155.186.124.219
|
|||
|
|||
Part II
If it is the pump leaking there should be a bit in the bilge and the plugs would look no different than usual as the coolant would be dumped directly into the oil pan.
In your case I suspect a breech as in my post above since your plugs are compromised. That indicates the coolant going through the combustion cycle and not just leaking into the oil. Dave Neptune |
#6
IP: 137.103.82.227
|
||||
|
||||
If the engine was RWC you might see a different result,. It would not run out of coolant and overheat, it would just keep filling the crankcase.
*If* if is just a leaky pump, try re-plumbing to RWC with the non-leaky pump |
#7
IP: 174.255.69.70
|
||||
|
||||
Quote:
Thanks for the heads up Dave. Yeah, I had read in one of the billetins that hard starting are causes for a leaky manifold...so attached is a pic of the number 1 plug. Also, how do I pressure test manifold? It is as easy as plugging up the exhaust section and pumping in from the intake of manifold? If so, I just did a few pumps and I could hear swirling inside towards block and no pressure being held...bad manifold then? Do I have this correct?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) Last edited by southcoasting; 08-12-2020 at 12:33 PM. |
#8
IP: 174.255.69.70
|
||||
|
||||
Posted pic of dipstick
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#9
IP: 155.186.124.219
|
|||
|
|||
First do a compression check!! f the compression is good it will be time to pressure check the manifold. The manifold is easy to check as all you need to do is plug one end of the water jacket and pressurize the other. Those points are where the coolant goes in and out of the manifold.
There are many links as to how to set up the manifold test with a "schrader valve", pressure gage and a bicycle pump. Once the results of BOTH tests are negative then time to test the block. Dave Neptune |
The Following User Says Thank You to Dave Neptune For This Useful Post: | ||
TimBSmith (09-11-2020) |
#10
IP: 174.255.69.70
|
||||
|
||||
Quote:
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#11
IP: 155.186.124.219
|
|||
|
|||
With the amount of coolant you are losing I doubt it's the manifold as that liquid would have to get past the rings to get into the oil. I think the compression check will yield your problem due to the amount of loss.
The water passage is sealed inside the manifold and only gets in & out via the two fittings on the top. Save time do a compression check first. Dave Neptune |
#12
IP: 137.103.82.227
|
||||
|
||||
WARNING - oil floats on water.
At first startup you are trying to lubricate the engine with pure water. After it runs a bit, you are trying to lubricate with oatmeal mush. Neither one works well. |
#13
IP: 174.255.68.4
|
||||
|
||||
Running compression test now...tons of water shooting up through plug holes...around 80 psi on all 4...cold engine
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#14
IP: 174.255.68.4
|
||||
|
||||
After replacing oring on pressure gauge, I got closer to 85-90 psi on 3 cylinders and 65 on cylinder 3
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#15
IP: 155.186.124.219
|
|||
|
|||
Did more moisture come out of #3?
Dave Neptune |
#16
IP: 174.255.68.4
|
||||
|
||||
There was so much on all that I really could not tell...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#17
IP: 155.186.124.219
|
|||
|
|||
Southcoasting, I "see" you have the water line into the manifold cut off. If you can just plug one end and blow into the other it should hold against you, if the pressure goes away quickly IE you have to keep blowing ~~ BINGO. This is not a good test but with the amount of liquid you are loosing the oral test might be fine. As a practice whenever I go to pressure check anything I do the same either by blowing or sucking. In many cases I did not have to hook up the gauge and stuff as the leak was obvious.
At 25lbs low it could well be the gasket but I would expect it to be lower. Dave Neptune |
The Following User Says Thank You to Dave Neptune For This Useful Post: | ||
TimBSmith (09-11-2020) |
#18
IP: 137.103.82.227
|
||||
|
||||
Seeing as this is a fresh overhaul, is there a plug or something somewhere someone forgot to put back
|
#19
IP: 174.255.68.4
|
||||
|
||||
I don’t know but I read about the plug on the valve side on one of the bulletins...the main thing to note though it that the leak at the manifold is significant...as soon as I pump my tire inflator I could hear a good amount of hissing shooting out in manifold. It does not hold any kind of pressure not ever for a millisecond
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#20
IP: 174.255.68.4
|
||||
|
||||
Quote:
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#21
IP: 155.186.124.219
|
|||
|
|||
Then the manifold is the culprit for the gobs of water.
Important, get the coolant sucked out of the engine and be ready to flush the oil a couple of times once you get the new manifold on. Be careful removing the exhaust, old exhaust systems that have a year or 2 left can easily snap off with not much effort. If you "hydrauliced" the engine you still may have a small breech in the head-gasket thus the low #3. Had you done a compression check any time before this incident? If so was #3 low? Dave Neptune |
The Following User Says Thank You to Dave Neptune For This Useful Post: | ||
southcoasting (08-12-2020) |
#22
IP: 155.186.124.219
|
|||
|
|||
Sorry, I missed part of your #7 post. Been a busy day.
Best Dave Neptune |
#23
IP: 137.103.82.227
|
||||
|
||||
That is good news, a new manifold and problem solved
|
#24
IP: 73.234.59.26
|
||||
|
||||
Quote:
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
#25
IP: 73.234.59.26
|
||||
|
||||
Just wanted to update on this...I had a spare manifold from my old engine which I had sandblasted and painted it...pressure was good on this one...
After about 9 hours or runtime most of which was a 5 day cruise to Martha’s Vineyard and Nantucket, all is good! There is an unusual amount of heat buildup on the aft end of manifold but maybe it’s normal...I will post something on this...all is good on this main issue though!
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014) 1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014) |
Tags |
fresh water cooling, fwc, overheating, rebuild |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Controlling and affecting proper operating temp | ILikeRust | Troubleshooting | 88 | 02-02-2016 01:36 PM |
coolant loss | wsulli | For Sale - Other Items | 4 | 01-06-2014 03:47 PM |
Sporadic coolant loss | jhwelch | Cooling System | 11 | 11-24-2011 04:28 AM |
Gradual Loss of Power, Overheating | forcenine | Fuel System | 5 | 03-03-2008 09:00 PM |
Overheating problems | jdaly986 | Cooling System | 1 | 01-16-2008 10:32 AM |