Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 50.67.146.231
Old 06-07-2018, 04:13 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Engine quitting when it reaches 160

Hello all...

I have taken ownership of a C7C 33 with an Atomic 4... this past week. The previous owner made no mention of my following condition.

Here's my issue, when underway with the engine running 1400 RPM @ 3-4 Knots the engine runs fine and smooth. However, if I try to increase speed to 5 knots the engine temperature reaches 160 on the gauge and the engine begins to falter and quit.

I waited 15-20 mins for the engine to cool down and she re-starts... This happened 4 times same thing every time, as I took her home to her new port.

As I drifted I googled this symptom... and came up with improperly gapped plugs. I called the owner and he said that he just installed them straight out of the box and did not gap them.

Since I don't own a spark plug gap tool to measure for .035 (on my way to buy one now) for the proper gap.. I am hoping that some of you might confirm that this is the issue with my engine.

I am planning to remove them check the gap and reset it the the proper distance... and run the engine to the stalling temp of 160 at the dock and see what happens.


I would appreciate any feed back...

Cheers

Mel
Reply With Quote
  #2   IP: 97.64.155.202
Old 06-08-2018, 01:34 PM
Ram41662 Ram41662 is offline
Senior Member
 
Join Date: Dec 2017
Location: Moline, IL
Posts: 158
Thanks: 75
Thanked 33 Times in 22 Posts
Since it appears to happen when things warm up, you might consider the coil could be getting weak. If weak, when it warms up it will produce a weaker spark until it fails.

Try the plugs first. If that fixes it, great! IF not, check the coil.
__________________
Just another Ol' Guy living the dream... :-)
Reply With Quote
The Following User Says Thank You to Ram41662 For This Useful Post:
Orion C&C 33 (08-03-2018)
  #3   IP: 72.194.220.204
Old 06-08-2018, 02:05 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
During the shut down time pull the wire out of the center terminal of the distributor and hold it near the engine while cranking the engine. If you don't see a blue white ~1/2 inch spark then the coil is suspect.

TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
Orion C&C 33 (08-03-2018)
  #4   IP: 71.222.3.150
Old 06-08-2018, 05:35 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by Orion C&C 33 View Post
...when underway with the engine running 1400 RPM @ 3-4 Knots the engine runs fine and smooth. However, if I try to increase speed to 5 knots the engine temperature reaches 160 on the gauge and the engine begins to falter and quit.

I waited 15-20 mins for the engine to cool down and she re-starts... This happened 4 times same thing every time, as I took her home to her new port.
Mel-
First, welcome to the Forum!

A few questions...
The 4 times it happened:
did it always run ok at lower RPM until you reached above 1400?

And to be clear:
it stumbles and then dies rather than shuts down suddenly (like turning off the ignition) right?

Do you know how old your exhaust system is?
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following User Says Thank You to roadnsky For This Useful Post:
Orion C&C 33 (06-09-2018)
  #5   IP: 12.40.28.99
Old 06-08-2018, 06:02 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Also: how does it run if you throttle up to a high RPM with a cold engine?

If it’s temperature-related, coil would be more suspect. If it’s RPM-related, an exhaust blockage (or bad timing or worn cap/rotor or old condenser or sticking advance weights) might be more likely implicated. I would not tend to blame the plug gap for this symptom - the A4 is not all that sensitive to gap width.
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
Orion C&C 33 (06-09-2018)
  #6   IP: 24.152.132.140
Old 06-08-2018, 11:15 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
In a pinch you can use a dime as a gap gauge. It's a little much @ 0.050 but I've heard of A-4's running fine @ 0.045"
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Orion C&C 33 (06-09-2018)
  #7   IP: 50.67.146.231
Old 06-09-2018, 02:48 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Thank you everyone... for the suggestions

I found out my problem on the motor.
I feel so incredulously stupid.... for not checking back in on this forum, I've been tinkering on the engine since I posted.

Please accept my apologies for my delay in response.

This is what I discovered spark plugs #1 and #3 were not tightened and seated properly, you can literally turn them out by hand.

and #2 and #4 were a little snugger but not by much... I assumed when the previous owner had changed out the plugs he would tighten them!!! But obviously not the case.

After checking out if they were gapped properly I torgued them down to the proper ft/lbs as suggest in the Atomic service manual...

Started it up and she ran like a Beauty right up to 160 degrees without stalling... then I tested the motor further and put it in gear while still tied to the dock and ran the engine to 180 degrees and again no stalling... ran it under load for 30 mins and nothing.

But in the process I and along with a friend have discovered that the electric fuel pump is kaput!!! It has to crank forever to get it to start... tested that issue out after cranking for about 5 minutes pulled the #1 plug out and she was visibly dry.

With some starter fluid squirted in the #1 pisten and she fired up immediately so I guess replacing the current electric fuel pump is next on the list, while she's on the hard.

Thank you for the warm welcome and for the help... I really much appreciate it.

Cheers

Mel

Last edited by Orion C&C 33; 06-09-2018 at 02:57 PM.
Reply With Quote
  #8   IP: 50.67.146.231
Old 06-09-2018, 02:53 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Quote:
Originally Posted by roadnsky View Post
Mel-
First, welcome to the Forum!

A few questions...
The 4 times it happened:
did it always run ok at lower RPM until you reached above 1400?

And to be clear:
it stumbles and then dies rather than shuts down suddenly (like turning off the ignition) right?

Do you know how old your exhaust system is?
Hi Jerry...

I could run it to 2000 rpm and still ran smooth... it was when the engine temp reached 160 then it sputtered and died like it was struggling... I have discovered that all my spark plugs were loose. Like turn them out by hand loose.

I feel so incredulously stupid for trusting the previous owners work... I know better next time to always perform a double check before leaving the dock... especially since I had my family on board.

Mel
Reply With Quote
  #9   IP: 24.152.132.140
Old 06-09-2018, 03:02 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Mel, do you run the fuel out of the carburetor when you shut down or simply turn off the key?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #10   IP: 50.67.146.231
Old 06-09-2018, 03:42 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
I just turn off the key... How do you run the fuel out of the carburetor ??

This is new to me....
Reply With Quote
  #11   IP: 24.152.132.140
Old 06-09-2018, 04:45 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by Orion C&C 33 View Post
I just turn off the key... How do you run the fuel out of the carburetor ??

This is new to me....
. . . . by closing a fuel valve and letting the engine run until it starves itself of fuel but that's not my point. Thus far you've said nothing that condemns the fuel pump so maybe not so fast on replacing it. Of course you can if you want, just that your reports do not fit a non functioning pump.

Examples:

It has to crank forever to get it to start You do not need a functioning fuel pump to start the engine. It has ample fuel remaining in the carburetor bowl to start and run for a minute or more without any fuel pump operation. My question about shut down procedure confirms there's fuel in the bowl.

ran it under load for 30 mins and nothing Not likely with a non functioning fuel pump. It's a remote possibility with a fuel tank situated so a strong siphon exists but I wouldn't count on it.

Your starting fluid test and dry #1 plug both confirm a fuel problem but let's not jump to conclusions it's the pump. It's possible it is, just that nothing's conclusive yet. Your symptoms may be due to other causes, even a combination of causes. Hard starting may be caused by a poorly functioning choke not closing all the way. A non-functioning fuel pump may be due to a failed oil pressure safety switch (OPSS). I encourage you to explore the entire fuel system before replacing things, home in on the real problem first. A fuel pressure gauge immediately ahead of the carburetor would answer a lot of questions about now.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Orion C&C 33 (07-09-2018)
  #12   IP: 50.67.146.231
Old 06-09-2018, 05:19 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Quote:
Originally Posted by ndutton View Post
. . . . by closing a fuel valve and letting the engine run until it starves itself of fuel but that's not my point. Thus far you've said nothing that condemns the fuel pump so maybe not so fast on replacing it. Of course you can if you want, just that your reports do not fit a non functioning pump.

Examples:

It has to crank forever to get it to start You do not need a functioning fuel pump to start the engine. It has ample fuel remaining in the carburetor bowl to start and run for a minute or more without any fuel pump operation. My question about shut down procedure confirms there's fuel in the bowl.

ran it under load for 30 mins and nothing Not likely with a non functioning fuel pump. It's a remote possibility with a fuel tank situated so a strong siphon exists but I wouldn't count on it.

Your starting fluid test and dry #1 plug both confirm a fuel problem but let's not jump to conclusions it's the pump. It's possible it is, just that nothing's conclusive yet. Your symptoms may be due to other causes, even a combination of causes. Hard starting may be caused by a poorly functioning choke not closing all the way. A non-functioning fuel pump may be due to a failed oil pressure safety switch (OPSS). I encourage you to explore the entire fuel system before replacing things, home in on the real problem first. A fuel pressure gauge immediately ahead of the carburetor would answer a lot of questions about now.
Hi Neil..

Very good suggestions... I am new to all this, not very mechanical minded, but I do like to solve problems and I'm not afraid to get dirty and learn from all you good folks on this forum.

Let me ponder on you advice... just as you advise in regards to the fuel pressure gauge, I don't have one at the moment.

So, If I'm going to change things out might as well replace everything and add on the gauge.

I do like the peace of mind... and not a big fan of being dead in the water other than my sails to move.

I'm fortunate enough to have a partner who says "change it all if necessary"

I'll get back to you after source out a fuel gauge... that can read the low PSI...


Cheers

Mel
Reply With Quote
  #13   IP: 24.152.132.140
Old 06-09-2018, 05:28 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Do you have the MMI manual?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #14   IP: 50.67.146.231
Old 06-09-2018, 07:59 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Hi Neil

Yes I do printed it off one copy for the boat and one for bedside reading... I have a lot to catch up on the Atomic 4.
Reply With Quote
  #15   IP: 173.30.41.140
Old 06-10-2018, 02:58 AM
Ram41662 Ram41662 is offline
Senior Member
 
Join Date: Dec 2017
Location: Moline, IL
Posts: 158
Thanks: 75
Thanked 33 Times in 22 Posts
Quote:
Hi Neil

Yes I do printed it off one copy for the boat and one for bedside reading... I have a lot to catch up on the Atomic 4.
I know this might be a silly question, but is your manual the Moyer Marine, Inc. manual or is it a version of an OEM manual? I have several versions of the OEM manual , all were available in PDF format, as well as a copy of the MMI manual, which is only offered in print.

That said, I will admit to scanning my copy to a PDF file I keep on a dedicated tablet that works as my "universal device manual library",
__________________
Just another Ol' Guy living the dream... :-)
Reply With Quote
  #16   IP: 50.67.146.231
Old 06-10-2018, 11:37 AM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
I know this might be a silly question, but is your manual the Moyer Marine, Inc. manual or is it a version of an OEM manual? I have several versions of the OEM manual , all were available in PDF format, as well as a copy of the MMI manual, which is only offered in print.

That said, I will admit to scanning my copy to a PDF file I keep on a dedicated tablet that works as my "universal device manual library"


I printed off the pdf version... needed something really quick to get the specs to get the gap right on my spark plugs.

Very handy I must say!
Reply With Quote
  #17   IP: 173.30.41.140
Old 06-11-2018, 08:53 AM
Ram41662 Ram41662 is offline
Senior Member
 
Join Date: Dec 2017
Location: Moline, IL
Posts: 158
Thanks: 75
Thanked 33 Times in 22 Posts
Yeh, TBH, I find each manual, even some of the odd parts list, handy in their own way, which is why I keep them all available in the shop.

The Moyer Marine manual is considered "The One Book to Rule Them All" by a lot of folks. I personally find it very handy and quite straight forward to use; a definite "must have" for long term Atomic 4 ownership.
__________________
Just another Ol' Guy living the dream... :-)
Reply With Quote
The Following User Says Thank You to Ram41662 For This Useful Post:
Orion C&C 33 (06-11-2018)
  #18   IP: 50.67.146.231
Old 07-09-2018, 07:12 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
My apologies for my delay in response...


Your starting fluid test and dry #1 plug both confirm a fuel problem but let's not jump to conclusions it's the pump. It's possible it is, just that nothing's conclusive yet. Your symptoms may be due to other causes, even a combination of causes. Hard starting may be caused by a poorly functioning choke not closing all the way. A non-functioning fuel pump may be due to a failed oil pressure safety switch (OPSS). I encourage you to explore the entire fuel system before replacing things, home in on the real problem first. A fuel pressure gauge immediately ahead of the carburetor would answer a lot of questions about now.[/QUOTE]

Found a quicker way to test the fuel pump, disconnected the line to the carburetor.. placed the end into a empty water bottle container and had someone push the start button... Confirmed no fuel is being pumped.

Then I disconnected the fuel line from the fuel filter to FP, no blockages the fuel flows freely.

Changed out the pump with an Acent electric pump... the motor started almost immediately! Been testing with multiple start tests over the weekend.

It's a sweet sound when the motor starts within seconds.

Thank you for your advice... much appreciated.

Cheers,

Mel
Reply With Quote
  #19   IP: 172.95.97.58
Old 07-10-2018, 12:53 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Did you check the OPSS wiring to be sure the pump was energized and supplying fuel during the start sequence?

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
Orion C&C 33 (07-11-2018)
  #20   IP: 137.200.32.6
Old 07-10-2018, 02:13 PM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
A fuel pressure gauge and jumping the OPSS would both be good things here.
Joe
Coquina
C&C 35 MK I
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
Orion C&C 33 (07-11-2018)
  #21   IP: 50.67.146.231
Old 07-11-2018, 12:35 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Quote:
Originally Posted by Dave Neptune View Post
Did you check the OPSS wiring to be sure the pump was energized and supplying fuel during the start sequence?

Dave Neptune

Hello Dave... Yes, it was a dead fuel pump and once I changed it out there has been no further issues starting it up.

Cheers,
Mel
Reply With Quote
  #22   IP: 50.67.146.231
Old 07-11-2018, 12:39 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Quote:
Originally Posted by joe_db View Post
A fuel pressure gauge and jumping the OPSS would both be good things here.
Joe
Coquina
C&C 35 MK I
I think so too... but I only have 6" if that to do what you suggested. I running out of room between the main fuel filter ahead of the pump and a new inline filter between the pump and the carburetor.

As mentioned in an earlier thread there is not much room on the carburetor side of things...

Cheers

Mel
Reply With Quote
  #23   IP: 172.95.97.58
Old 07-11-2018, 01:06 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Lightbulb

Mel, the gage can be mounted in a visible spot and connected with a "loop" in the hose. And a convenient place to mount a shut off valve is the gage. The gage eliminates an awful lot of guessing.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
Orion C&C 33 (07-11-2018)
  #24   IP: 50.67.146.231
Old 07-11-2018, 05:54 PM
Orion C&C 33's Avatar
Orion C&C 33 Orion C&C 33 is offline
Senior Member
 
Join Date: Jun 2018
Location: Richmond BC, Canada
Posts: 66
Thanks: 68
Thanked 12 Times in 4 Posts
Quote:
Originally Posted by Dave Neptune View Post
Mel, the gage can be mounted in a visible spot and connected with a "loop" in the hose. And a convenient place to mount a shut off valve is the gage. The gage eliminates an awful lot of guessing.

Dave Neptune

Hey Dave...

I've read somewhere on this site that those low pressure gauges are hard to find... Yes, you are right installing a gauge will take a lot of guess work out.

My mechanical skills have been limited to animatronics, servicing servo linkages and motors. So this is all new to me.

Although intimidating at first when I looked at this motor, I've come to appreciate it simplicity.


Cheers David!

Mel
Reply With Quote
  #25   IP: 67.176.202.26
Old 07-12-2018, 12:14 AM
Sam Sam is online now
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
$20 US buys a good one on EBAY _ Russell, Marshall, Jeggs etc. I bought "Marshall" 0 to 15psi since it was stainless case w/real glass lens this year. I chose "liquid filled" [vs air filled] and it performs fine to date. Brass hose "t" adaptor was another $12. Having this gauge is highly recommended by the pros on this site and for good reason.
Reply With Quote
The Following 2 Users Say Thank You to Sam For This Useful Post:
Dave Neptune (07-12-2018), Orion C&C 33 (07-15-2018)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Engine Hoist and Gas Drum Removal Jim Bates General Interest 22 09-24-2013 05:36 PM
Fuel-Related Engine Shutdowns Don Moyer Fuel System 32 02-18-2011 04:36 PM
Short? Or bad component preventing engine from shutting off? ILikeRust Troubleshooting 23 10-25-2010 08:52 AM
Engine Dies after approx one hour Trysail Troubleshooting 4 08-07-2008 11:15 AM
Removing the engine from your boat Don Moyer Ranger 7 12-12-2005 12:24 PM


All times are GMT -4. The time now is 05:28 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved