Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 47.184.78.228
Old 03-30-2018, 09:05 PM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
Atomic 4 overheating

I'm negotiating a 1982 Catalina 30 with an Atomic 4 gasoline engine that is raw water cooled. The survey was today and found only one major issue.

The engine overheated in the following way. Engine started and warmed up to about 160 degrees. Ran for 10 minutes at idle. Adequate cooling water discharge was observed. Surveyor shut down the engine for 30 mins. Started the engine. Warmed up to 160 at idle. Engaged forward gear and opened throttle to about 3500-4000 rpm. The engine overheated with temp spiking over 200. Shut down engine. Some soke from engine compartment and surface reading on the engine head were 210-220 at various places.

Any ideas what cause the overheating with cooling water flowing?

Every other aspect of the boat was solid.

Thanks,
KBG
Reply With Quote
  #2   IP: 155.186.126.158
Old 04-01-2018, 11:03 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,033
Thanks: 711
Thanked 1,284 Times in 837 Posts
KBG, first welcome to the MMI Afourian Forum.

First lets talk RPM I've never seen an A-4 get that kind of RPM tied to a dock even one with a reduction unit. In the C-30 it is probably a direct drive (1500~2200 RPM's) and getting past 2000 requires a lot of prop work.

Now for the heating with good flow. First is it raw water cooled or is there a heat exchanger? Is there a thermostat installed and/or a bypass valve to control temps.

It is not hard diagnosis just need some info.

Dave Neptune
Reply With Quote
  #3   IP: 47.184.78.228
Old 04-01-2018, 11:31 AM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
Thanks for the reply Dave. I appreciate the warm welcome!

It is a raw water cooled engine fed directly from the through hull. No heat exchanger. Fresh water lake boat. It has a thermostat installed to control water flow into the manifold as the engine warms up.

As for the RPM, I was keeping an eye on the tach so I know that's accurate. Are you saying the engine was over-revved and that's what caused it to over heat?
Reply With Quote
  #4   IP: 155.186.126.158
Old 04-01-2018, 11:50 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,033
Thanks: 711
Thanked 1,284 Times in 837 Posts
KBG, as far as the RPM's it could also be the tach is on the wrong setting not to uncommon. I doubt the RPM's have much to do with the heating.

Is there a line that runs from the water injection point on the side of the block (a tee) up to the thermostat housing and is there a valve in that line?

The water needs to circulate through the block. When the t-stat is closed the water is rerouted through the bypass line to the exhaust manifold skipping the "block". So we need to know if the t'stat is good. It can be easily removed and checked in a pan of hot water with a thermometer to check the opening temp.

Many many of the A-4's running today do not use a t'stat ie it is removed. When removed the bypass valve is used to regulate engine temps. I ran like this for over 30 years on the same motor that is now running for someone else. Valve closed max cooling as it all goes through the block~valve opening bypasses the block to increase temps and still all the water goes out the back.

If you remove the t'stat just put the housing back on and give it a try IF YOU HAVE A BYPASS VALVE. Then monitor the heat. Don't worry about using an IR gun for checking head temps watch the gage. Due to the flow pattern of the water and a "flathead" design there a many varying temps on the head when running.

Dave Neptune

Last edited by Dave Neptune; 04-01-2018 at 11:54 AM. Reason: not done with the post
Reply With Quote
  #5   IP: 24.152.132.140
Old 04-01-2018, 11:53 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,617
Thanks: 197
Thanked 2,204 Times in 1,424 Posts
A blockage in the block and/or head could cause the overheating but because of the bypass style cooling system that delivers full flow through the manifold at all times you would not notice a change out the exhaust. This suggests to me an acid flush is in order at a minimum, perhaps opening the water jacket side plate and physically mucking out the water jacket.

Quote:
Originally Posted by kbgunn View Post
As for the RPM, I was keeping an eye on the tach so I know that's accurate. Are you saying the engine was over-revved and that's what caused it to over heat?
Please reconsider Dave's comment. With a direct drive A-4 and Catalina's typical 12 x 7 fixed two blade prop it's simply not possible to achieve 3500-4000 RPM in forward gear. Out of gear, yes but in gear, no way.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #6   IP: 47.184.78.228
Old 04-01-2018, 12:22 PM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
I will have to re-check the cooling system configuration to see if a bypass valve is installed. It will require a trip to the boat. Thanks Dave and ndutton for sharing your experience with a newbie. All of my previous experience is with outboard motor so this is all new territory for me.

-KBG
Reply With Quote
  #7   IP: 72.194.220.204
Old 04-01-2018, 01:57 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by kbgunn View Post
It is a raw water cooled engine fed directly from the through hull. No heat exchanger. Fresh water lake boat. It has a thermostat installed to control water flow into the manifold as the engine warms up.
As for the RPM, I was keeping an eye on the tach so I know that's accurate. Are you saying the engine was over-revved and that's what caused it to over heat?
The thermostat may be broken and stuck in the closed position. This would force the cooling water to go around the engine by way of the bypass rather than through the engine
The tach may be set for an eight cylinder engine which would make the four cylinder reading 1/2 the actual reading.

TRUE GRIT
Reply With Quote
  #8   IP: 98.165.207.17
Old 04-01-2018, 03:54 PM
zellerj zellerj is offline
Afourian MVP
 
Join Date: May 2005
Posts: 304
Thanks: 5
Thanked 115 Times in 69 Posts
Overheating on an Atomic 4 is fairly common and easy to fix. I would not let it be a "walk away" issue, but possibly a negotiating issue. Fixing it requires checking out the thermostat and the thermostat housing, making sure the mixing T is clear of old broken impeller vanes, checking the water exit elbow on the exhaust manifold, and as Neil said, removing the side plate and getting rid of 36 years of crap. With good water flow and high operating temps, the water is not circulating around the cylinder tubes and head like it should. There has to be a blockage somewhere, and finding it and fixing it is usually not that hard to do.
__________________
Jim Zeller
1982 Catalina 30
Kelleys Island, Ohio
Reply With Quote
  #9   IP: 47.184.78.228
Old 04-01-2018, 05:54 PM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
Quote:
Originally Posted by zellerj View Post
Overheating on an Atomic 4 is fairly common and easy to fix. I would not let it be a "walk away" issue, but possibly a negotiating issue.
Good to know it's not a major issue. It's a solid boat with no water intrusion in the plywood core and very minimal cracking in the gelcoat. I will definitely use the overheating as a bargaining point.
Reply With Quote
The Following User Says Thank You to kbgunn For This Useful Post:
CajunSpike (04-01-2018)
  #10   IP: 70.186.109.11
Old 04-01-2018, 08:30 PM
CajunSpike's Avatar
CajunSpike CajunSpike is offline
Senior Member
 
Join Date: Jan 2018
Location: New Orleans, LA
Posts: 240
Thanks: 222
Thanked 41 Times in 31 Posts
Just had to fix an overheat on my A4. The manifold outlet was clogged. Stuck a screwdriver in the outlet hole...wiggled it around.

Freed up the clog and now so cool it doesn't show on the temp gauge.
__________________
Bill L.
1972 Ericson 27
Hull #61
Atomic 4
Reply With Quote
  #11   IP: 67.186.97.244
Old 04-02-2018, 09:50 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 489
Thanked 140 Times in 109 Posts
I think worst case is you have a somewhat worn impeller or water pump. It would still have fair amount exhaust flow out he back but it is hard to determine if it is 10 -20 - 30% less if you haven't had the boat for while. Impeller $35, water pump about $300 with an hour of simple labor. There is a rebuild kit available as well. On the late model engines with a thermostat 160F is standard with raw lake water. I had same problem with my early model A4 few years back - changed pump to bigger oberdofer pump and temp cooled down to 140 F. Good luck, definetly not a deal killer.
Reply With Quote
  #12   IP: 32.211.28.40
Old 04-03-2018, 11:15 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
Definitely not a deal killer. If the present owner pays to have it corrected, give him his price. If it's an as-is sale, it's worth negotiation as you're buying his problem.
Reply With Quote
  #13   IP: 71.178.88.164
Old 04-04-2018, 10:33 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,015
Thanks: 1,132
Thanked 600 Times in 442 Posts
Thumbs up

KBG, WELCOME!
Be sure to check the 360° panoramic motor on the home page here..We can use that as reference to make sure you know all the parts being referenced in this discussion. The Bypass Dave is referring to is the copper pipes with the silver valve in the middle over on the stbd side of the engine..this can adjust/regulate the amount of cooling water being forced into the block. The t-stat housing is in between the copper tubes and the red hoses on top of the head.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #14   IP: 47.184.78.228
Old 04-09-2018, 08:17 PM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
That 360 photo is a good resource. I don't think I have the bypass valve. I don't have a good photo but you can kinda see in this one:


I don't have access to the boat at the moment. It looks like the bypass is an after market mod? Probably one that is worthwhile since it eliminates the need for a t-stat?
Reply With Quote
  #15   IP: 70.186.109.11
Old 04-10-2018, 12:11 AM
CajunSpike's Avatar
CajunSpike CajunSpike is offline
Senior Member
 
Join Date: Jan 2018
Location: New Orleans, LA
Posts: 240
Thanks: 222
Thanked 41 Times in 31 Posts
The bypass valve is circled in this motor shot.
Other than connecting the hose to a valve, then to the thermostat cover, there's not much to it.
__________________
Bill L.
1972 Ericson 27
Hull #61
Atomic 4

Last edited by CajunSpike; 04-10-2018 at 12:17 AM.
Reply With Quote
  #16   IP: 107.242.113.10
Old 04-10-2018, 01:35 PM
kbgunn kbgunn is offline
Frequent Contributor
 
Join Date: Mar 2018
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
Thanks for another view CajunSpike.

If I'm understanding correctly, normal operation is to start a cold engine with this valve OPEN to bypass the engine block cooling passages. As the engine warms and temp rises, partially or fully CLOSE the valve to force water into the engine block passage. As part of final shutdown procedures for the day, turn the valve back to OPEN position.

This will eliminate the need for a t-stat altogether and the t-stat housing will be empty.
Reply With Quote
  #17   IP: 172.95.97.58
Old 04-10-2018, 02:37 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,033
Thanks: 711
Thanked 1,284 Times in 837 Posts
k, no need to constantly adjust. I never touched mine unless I saw it getting to around 130* then I would adjust closed a bit and look for why the beastie was running warmer.
Use a "ball valve" when you do install and try it at about half open. The ball valve with it's lever action gives a good visual reference as to how far it is open or closed. It will take a long time to warm so take her for a spin under load. After a half hour or 45 minutes the engines temp should settle~THIS is when you make your setting adjustment~ once set you will not need to touch except for minor adjustments as to seasonal water temp changes.

ALSO be sure the t'stat is REMOVED!

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
Administrator (05-09-2018), tlross (04-11-2018)
  #18   IP: 74.196.210.38
Old 05-09-2018, 02:46 PM
sailr sailr is offline
Senior Member
 
Join Date: Apr 2018
Posts: 14
Thanks: 0
Thanked 6 Times in 3 Posts
Hot running engine

I had an atomic 4 that ran hot. I tried acid flush and vinegar flush with little improvement. I finally pulled the head and discovered that all the cooling channels were blocked with some type of sedimentary stuff. The channel from the thermostat housing was affected also. I had to take a drill and actually rebore where the channels were blocked. It was easy to tell where the channels were by the change in texture from metal to rock like mess. Easy to see why the acid flush and vinegar flush didn't work. After I bored all the channels out I flushed the head with 6% acetic acid and made sure everything was open. I replaced the head with new gaskets of course and after reconnecting everything I fired her up and Viola! no over heating. If all the other efforts fail take a look at the head and the cooling channels there.
sailr
Reply With Quote
  #19   IP: 137.200.32.6
Old 05-10-2018, 09:54 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,457
Thanks: 49
Thanked 1,022 Times in 717 Posts
You got some good advice.
I would get a cheap portable tach and find the true RPM. No way is any direct drive A4 getting 4,000 RPM. 3600 is redline!
Actually getting past 2400-2500 with a displacement hull is almost unknown.
Now for the temps......This could be trivial and it could NOT be trivial to fix. The gauge itself could be bad. An IR gun will work to an extent, but you need to know what to aim it at. Two good points are the thermostat housing and the temperature sender itself. Do not aim around the spark plugs or over where the valves are, it gets hot over there.
If the engine does overheat, keep in mind mud and biological debris exist in fresh water and iron rusts in fresh water too, just not as fast as in salt. There could be significant clogging in the engine.
As a *buyer*, I would be going OMG that engine is dead I need a big discount
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
overheating ordeal, four days to fix it. capnward Cooling System 3 06-11-2015 08:41 AM
Catalina Atomic 4 No Crank Problem Resolved Don Moyer Catalina 27 01-10-2013 11:20 AM
Overheating problems jdaly986 Cooling System 1 01-16-2008 10:32 AM


All times are GMT -4. The time now is 05:32 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved