#51
IP: 96.246.123.218
|
||||
|
||||
glad you solved your problem
I'll just add for anyone else encountering fuel problems. after going thruogh very much the same frustrating exercise of replacing everything all the way back to the tank. clogged fuel lines blown fuel pump(s) the biggest problem was a tank filled with sediment |
#52
IP: 216.70.184.248
|
||||
|
||||
We seem to have lost sailhog for the moment. (Too much Guiness?)
BUT my guess is that this had something to do with the distributor. Any other guesses?
__________________
-Jerry 'Lone Ranger' 1978 RANGER 30 |
#53
IP: 173.20.99.40
|
|||
|
|||
Sorry for the delay, gentlemen....
My daughter ran into a mailbox on her bike, requiring a trip to the doctor. No major injuries, but the Neosporin is everywhere... Unfortunately this story isn't over. This morning I tried to start her, and with some difficulty she got going. This is in marked contrast to the last when I had her running the day before yesterday. I would turn her off, and she would start without any trouble whatsoever. Once I got her going this morning, she seemed to run rough... something seemed to be up. I turned her off, tried to turn her on again, and she wouldn't go. I tried three or four more times... then did a compression check: 80; 70; 100; 65. She was getting spark, which left fuel. When I check the throat of the carb, a big ol' pile of water, rust, MMO, and fuel came pouring out. That's right: I had forgotten to close the raw water seacock. I went to the manual: popped the sparks, turned her over until all the evidence of water was gone. When I put her back together, she still wouldn't start, and when I pulled a plug, there was still water on it. I did this routine about three times without success, and finally popped the manifold. Water came pouring out every which way. Right now I have the manifold off so as to allow her to dry out. I have the sparks out with a paper towel over the holes in order to keep condensation out. Argh. Looking back, it seemed that when she was running this morning, the water may have been exiting the transom a little less vigorously. I recall seeing all sorts of monkey crap coming out of her when I first started her up, as I'd had popped the head and cleaned out the water ports -- and there was plenty to clean out. I'm wondering if there could be a clog in the exhaust somewhere downstream of the manifold.... If so, any ideas as to how to locate and then clear it? This thing is wearing me down.... She was running SO well. Anyway, I think that once she's dried out, all should be well... I promise I'll tell you the whole tale once you guys solve each and every one of my problems.... but not until then! Thanks again, gentlemen.... |
#54
IP: 66.87.6.83
|
||||
|
||||
Did you install two fresh gaskets after taking the head off? Sounds like you might have a leak in that area.
|
#55
IP: 24.152.131.220
|
||||
|
||||
What got her running Wednesday?
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#56
IP: 173.20.99.40
|
|||
|
|||
I installed two new head gaskets, and I've got adequate compression. I'm pretty sure the water came in via the exhaust system.
|
#57
IP: 173.20.99.40
|
|||
|
|||
Neil, I can't tell you until AFTER she's up and running again....
Well, okay.... there was some residual water in the cylinders and that's what kept her from firing. Dave Neptune called it. I dried her out by getting her to run for a few seconds, then popping the plugs to let the steam escape. I did this about seven or eight times.... I've got a long tale to tell.... I just need time to sit down and do it.... Thanks for everything.... |
#58
IP: 24.152.131.220
|
||||
|
||||
Thanks.
You teased us Wednesday then left us hanging for two days. Looked like you were gonna do that again. I don't think I could take another two days!
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#59
IP: 72.1.195.4
|
|||
|
|||
Squeegie bulb
I seek information re the role of the above, the cost and the supplier.
aloha |
#60
IP: 24.152.131.220
|
||||
|
||||
Hate to use these guys as a source but sometimes convenience trumps cost.
http://www.westmarine.com/webapp/wcs...classNum=10446 They have a variety of sizes, the one referenced is 1/4". It's used to move fuel through the system independent of the pump, many times a diagnostic tool around here.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#61
IP: 173.20.99.40
|
|||
|
|||
Neil, here's another detail to keep you hanging.... the entire process has involved taking the head off not once... but TWICE!
|
#62
IP: 138.88.81.142
|
||||
|
||||
sailhog...You must get it running as soon as possible...the water in the cylinders is BAD NEWS. It rusts those unprotected metal parts within hours.
Also, you may have water in the crankcase too...you probably need to do an oil change or three to get the water out of there too. Sorry about your daughter...Mine just came home from college for spring break and we put a new battery in her car, so I feel your pain.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
#63
IP: 173.20.99.40
|
|||
|
|||
Gentlemen, the saga continues....
After having run her three or four times for a total of 2-3 hours a few days ago, I got a little water in the combustion chambers after a hard start followed by a compression check (during which I remembered I hadn't closed the seacock). I pulled the plugs and turned her over in order to blow out all the water. Cylinder #3 cleared up pretty quickly, but cylinder #4 (aft-most) took about 20 attempts. The good news is that she's dry. The bad news is that she doesn't want to start. I think she's sick of me. Anyway, here's the rundown: I've got spark at all 4 plugs; compression: 95; 70; 85; 75; when I unscrew the bolt at the bottom of the carb (not the main jet, but the one on the bottom) plenty of fuel comes out. Also, when I put my hand over the carb throat with the flame arrestor removed, I can feel the whoof, whoof whoof of suction as I turn her over with a screw driver on the starter. The carb appears to be closing all the way. I've got a new carb cable in to make sure she operates as designed. One more clue: Ether doesn't seem to work either. Whether I have her fully choked or have given her a shot of ether, all she does is fire a little bit, then nothing. It's as though she's fuel starved. When I pull the plugs after trying to start her, they are barely moist with fuel. Sometimes they're completely dry. I don't know what they should look like, but I'd think they should be pretty dang saturated. My only theories are she's flooding and I don't know it... or.... I don't know. I'm totally flummoxed.... I'm ready for her to run.... Thanks gentlemen. Whoever figures this out gets to take my wife to the Golden Corral for the all-you-can-eat buffet.... |
#64
IP: 173.20.99.40
|
|||
|
|||
Shawn,
Thanks for the note of urgency. I'm trying to get her going asap.... By the way, would anyone have any additional methods of drying out the combustion chambers? As stated above, I pulled the plugs and turned her over many times. There doesn't seem to be any evidence of water in the combustion chambers at this point, but you never know. Maybe this is indeed what's keeping her from firing? Again, thanks everyone... |
#65
IP: 138.88.81.142
|
||||
|
||||
sailhog,
what about heat from a lightbulb (shoplight on the head maybe?) - That may evaporate the water in the cylinders. What is the condition of the fuel? I cannot recall if we've discussed this yet. One option is to get an outboard tank to eliminate the fuel system and connect it directly to the fuel pump, or even directly to the carb inlet (gravity feed..) to eliminate the fuel pump as well. These are just some ideas to get rid of various components to try to figure out why she isn't running. One more comment...I have become anal about the seacock..I'd almost rather start her without water and then remember to open it than the other way around...water ingest thru the exhaust has such catastrophic consequences, I'd rather shorten the impeller life and replace it every season. - This is even more critical during "hard" or "no" start scenarios..depending on how your boat is set up, it can take mere seconds of cranking with it open to start it backing up. That's all I got for now..maybe tomorrow, I'll review this thread again. Spark, fuel, compression, (& some oxygen) is all she needs. Maybe time to go back to basics here.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 03-22-2011 at 08:23 AM. Reason: cleaning up my grammar! |
#66
IP: 206.125.176.3
|
||||
|
||||
we need a running engine again
OK sailhog...a nice fresh cup of coffee, a review of this thread & we're ready to go. How's your daughter? Mine gets her wisdom teeth yanked tomorrow..busy spring break!!
Now, I am just going to lay out my theories & suggestions, so, please don't be offended..I stand by my earlier statement, we MUST get this engine running ASAP to avoid further, or more permanent damage. You've been thru so many different issues now, it can get confusing..let's try a methodical approach here. I will lay out what I think that should be. First, a couple of comments:
Now a couple of suggestions: If it was my motor, here is what I'd do, in this order:
After all those are done (I know it is a long list, but we have a big mess to clean up now) I'd fully close the choke, & attempt to start. Once you get it running & it won't quit, open the seacock. If the engine stalls, turn off the key, & CLOSE THE SEACOCK! It is just a habit you'll need to train yourself to get in to so you don't continue to fill the motor with water. OK, there is my $0.02! Please report back!
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
#67
IP: 173.20.99.40
|
|||
|
|||
Shawn! Thanks for this most thoughtful and logical response! The choke has been fixed, the carb cleaned as recently as yesterday, the fuel changed twice, the seacock has been closed (I even removed the impeller in order to spare it).
I'll be heading out there again to give it another shot. I'll be reporting back with all the gory details.... I spoke with Capt. Hanley on the phone last night, and worked through a list of possibilities. His principal suggestion: concentrate confirming or establishing a good strong spark. I'm going to put in new plugs and tighten up the points setting, along with a couple of other adjustments... Please chime in with any additional suggestions -- and the sooner the better, as I'm heading out to the boat soon.... Thanks for taking the time. I truly appreciate it. Dwight |
#68
IP: 173.20.99.40
|
|||
|
|||
This thread is getting longer than I ever hoped it would....
I checked the engine-side ignition at each step, and found no problems. However, when I checked the new plugs, they were bone dry. There was fuel in the carb bowl, but I'm now thinking that I have a faulty electric fuel pump. It produces fuel, but perhaps with inadequate pressure. When the engine was running a few days ago, I recall having to prime the engine every thirty seconds or so in order to keep the engine running. I thought this was the due to an air leak in the fuel line, but now I'm wondering if it's because the fuel pump wasn't getting it done.... I had assumed that since there was some fuel in the bowl, and that the pump does produce fuel, that it wasn't the culprit. Anyone care to venture a guess? It isn't spark, it isn't compression, it isn't the carb.... Again, the plugs were dry, dry, dry.... What thinkest thee? Me thinkest the rusted hulk of an old electric fuel pump has some explaining to do.... |
#69
IP: 99.50.221.233
|
||||
|
||||
Just went through the same symptoms, turned out to be a failed oil pressure safety switch. Might want to jumper the switch terminals and give it a try.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#70
IP: 173.20.99.40
|
|||
|
|||
Neil,
How do you do this? There is only one wire coming from the oil pressure safety switch to the fuel pump. This has been mentioned before, but it's never been explained exactly how to go about doing this... |
#71
IP: 138.88.81.142
|
||||
|
||||
sailhog,
I am guessing here since I have a mechanical fuel pump. I think you take a pair of alligator clips (obviously connected with a wire) and hook one to each terminal of the switch...this bypasses the switch's normal function which closes the circuit on its own at xx PSI. Remember however, with the jumper wire connected, the fuel pump is running 100% with the key turned on. If this works in terms of fuel delivery, you can likely eliminate my step about putting an outboard tank above the carb and plumbing the line directly into the carb inlet. Keep at it buddy, we are almost there!
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
#72
IP: 173.20.99.40
|
|||
|
|||
Shawn,
I have fuel coming out of the pump (into a jar) when I attempt to start the engine, so wouldn't that indicate that the oil pressure safety switch is operating properly? If so, perhaps the fuel pump is moving fuel but not at an adequate rate? Thinking out loud here.... |
#73
IP: 138.88.81.142
|
||||
|
||||
Perhaps, but to really tell I think you would need a pressure gauge in the line.
An outboard tank that can gravity feed directly to the carb would eliminate this outlier. Again, I have a mech. pump so I am not 100% sure on how the electric pump idiosyncrasies work.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
#74
IP: 128.183.140.38
|
||||
|
||||
Quote:
__________________
@(^.^)@ Ed 1977 Pearson P-323 "Dolce Vita" with rebuilt Atomic-4 |
#75
IP: 173.20.99.40
|
|||
|
|||
Edward,
Thanks! How do you open the bottom of the Facet pump? Does it unscrew? Last edited by sailhog; 03-23-2011 at 10:49 AM. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
new carb good fuel and spark same proglem | chiron | Fuel System | 31 | 03-02-2011 11:51 PM |
Fuel-Related Engine Shutdowns | Don Moyer | Fuel System | 32 | 02-18-2011 04:36 PM |
No start- fuel flows to carb, not to sparks | Brosov | Fuel System | 1 | 10-03-2010 12:49 PM |
Facet fuel pump notes | rigspelt | Fuel System | 3 | 01-03-2009 01:31 PM |
Fuel problems - A happy story | Concord | Fuel System | 1 | 07-09-2008 03:27 PM |