#1
IP: 45.48.80.165
|
||||
|
||||
Stumped
Hello. I am trying to get my A4 started. Yesterday I was checking spark and my engine fired and sputtered with one spark plug out and testing spark. It did this on each spark test. Does this indicate anything? When i put all the plugs back in, it does not fire.
|
#2
IP: 24.152.132.140
|
||||
|
||||
Sounds like timing to me.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#3
IP: 45.48.80.165
|
||||
|
||||
I have an electronic ignition, is it find tdc, then point rotor and tab away from block, then adjust position of the distributor?
|
#4
IP: 24.152.132.140
|
||||
|
||||
More than that. It is finding TDC on the compression stroke for cylinder #1 then making certain the rotor inside the distributor points to the post on the cap where the #1 spark plug wire is connected. From there, confirming the firing order is correct.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
The Following User Says Thank You to ndutton For This Useful Post: | ||
Rando1201 (05-25-2020) |
#6
IP: 72.69.36.126
|
|||
|
|||
First make sure you have the plug wires led correctly between the plugs and the distributor. It is pretty easy to get them mixed up. I label my wires, and have labels on the distributor cap, to make absolutely positively sure.
|
#7
IP: 174.242.135.200
|
||||
|
||||
And it is OK if you discovered you are 1-2-3-4 and not 1-2-4-3... it happens to good people...
__________________
Surcouf A nostalgic PO - Previously "Almost There" - Catalina 27 (1979) |
The Following User Says Thank You to Surcouf For This Useful Post: | ||
Sam (05-25-2020) |
#8
IP: 45.48.80.165
|
||||
|
||||
Ya I've gone through the whole plug coordination. 1,2,4,3 . I did the timing test like in Don's video with the continuity tester. Only thing is I did a reversing gear swap and dont have all the bolts in the housing. Initially I jumped the gun and didn't have the bolt in by the water pump and the housing that holds the distributor fell off.
So maybe if I pop all the bolts in the housing for the transmission it will give me more compression. Just guessing here. And I also noticed that my coil is getting hot. I tested ohms and both tests are good. I even borrowed a carb off a new friends boat and still nothing. Well not nothing. It does tease me and sputter up. I'm normally a pretty good shade tree mechanic but dang man I'm getting my ass kicked. |
#9
IP: 45.48.80.165
|
||||
|
||||
Update. The A4 lives!
Backstory. Totally spaced this, when I initially got the motor I bought gasket material. I had my lady cut the gasket because she does crafting for work in the visual department. She got stuck because the heat protected gasket material was tough for her to cut. So I got angry. Slapped on the gasket without the hole cut to the exhaust. I must of thought I'd put it on, then fix it the next day. I spaced it, until I pulled the plugs out one by one and the motor started right up with a plug missing. Now I'm really stumped. Hitting up all my friends, mentors, no one had a solid answer. So I thought to myself well it's a used motor, so let's check for blockage in the exhaust. I pulled the exhaust off and saw the gasket. Oh no you idiot! The engine could be in the boat by now. I pulled the gasket off and the engine fired right up! On the positive side I can now: Swap direct drive for v drive Set timing - properly Test a coil Rebuild a carburetor (did this maybe 30 times adjusting the float. Id like to find another non running motor and fix it up. |
The Following 2 Users Say Thank You to Rando1201 For This Useful Post: | ||
Dave Neptune (05-27-2020), Surcouf (05-26-2020) |
#10
IP: 72.69.36.126
|
|||
|
|||
Congratulations!
That is probably not the worst mistake ever made. Not even bottom decile. |
#11
IP: 165.225.38.121
|
||||
|
||||
exhaust blockage is one of the potential culprit. This one is indeed a little more creative!!
And your oil is likely loaded with gas now. Tt is going to run hard with the crank case sucking vapors of fuel... So: Fuel - Air - Ignition - Timing (including spark plug order) - Exhaust free of plugs
__________________
Surcouf A nostalgic PO - Previously "Almost There" - Catalina 27 (1979) |
The Following User Says Thank You to Surcouf For This Useful Post: | ||
GregH (05-27-2020) |
#12
IP: 45.48.80.165
|
||||
|
||||
Quote:
Quote:
|
#13
IP: 32.211.28.40
|
||||
|
||||
Already posted on FB, may as well post here...
No, that gasket with no hole is a feature. Keeps that pesky exhaust water from getting back into the cylinders. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Stumped and confused | ckohler0529 | Electrical | 7 | 07-09-2017 08:40 PM |
A4 Has Me Stumped... | August West | Troubleshooting | 4 | 04-22-2014 11:36 PM |
Atomic 4 Symptoms~I'm Stumped | Herron | Catalina | 4 | 10-14-2008 12:52 PM |
Completely Stumped.... | Kurt | Troubleshooting | 19 | 08-12-2008 04:20 PM |
Atomic 4 runs, stops and then starts up~stops again~I'm stumped. | Herron | Troubleshooting | 24 | 08-07-2008 03:58 PM |