Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 216.54.200.157
Old 11-20-2006, 11:20 AM
jkenan jkenan is offline
Senior Member
 
Join Date: Mar 2005
Posts: 64
Thanks: 0
Thanked 0 Times in 0 Posts
MMO or Cool temp contributing to fouled plugs

After rebuilding my engine last winter, it ran great all summer, after going out several times this fall and winter, I have had a terrible time with fouled plugs.

The first sign of trouble was mid-October (after not being used since Labor day weekend), when the engine had very little power and sounded like it wanted to stall. I dis-assembled and cleaned the carb, but determined that was not the issue since it was already very clean. I checked my fuel vent, and it was fine. Finally, I removed the plugs to squirt some MMO to valves, which I thought were stuck. After doing that, I inspected the plugs, and they were badly fouled, so I replaced them. Engine ran great. At the end of that trip, I filled up and put high a bit more than the 4oz to 10gal MMO ratio in the gas, and squirted some more MMO in the combustion chamber, both for good measure. A couple of weeks later I used it, and it ran great. Before leaving it, I repeated the same. This past weekend, same problem. I pulled the plugs, and they were badly fouled.

I realize there could be several things going on here:
1) Too much MMO in the gas - exhaust smoke is white, but seems to dissipate into the air very quickly. This makes me think it is just vapor from the cooling water interacting with the cold air, and not oil - either MMO or oil getting past the rings (oil level remains steady).

2) Too much MMO squirted into the combustion chamber - could this foul plugs quickly? The first time I had a loss of power issue, it could very well have been stuck valves which was resolved by MMO.

3) Engine running too cool - average running temp is about 130 degrees. During the summer when the water was warmer, it was about 140 degrees. How can you make the A4 run hotter besides partially closing the seacock - which I did this last time out, with new plugs (I did not squirt any more MMO into the chamber after replacing the plugs) and they seem pretty clean after motoring about 6 hours?

I know I probably need to approach this more methodically, but as the problems surfaced, I did what I thought was necessary to get it running again, without proper thought to testing the cause. I won't be using the boat for the next couple of months, so I figure would be best put this all out to the discussion board for feedback.

Thanks for any thoughts on the matter.

John
__________________
John Kenan
Ericson 29, Carried Away
Efland, NC
Reply With Quote
  #2   IP: 68.49.221.86
Old 11-20-2006, 09:19 PM
MikeB.330's Avatar
MikeB.330 MikeB.330 is offline
Senior Member
 
Join Date: Jun 2006
Posts: 247
Thanks: 0
Thanked 0 Times in 0 Posts
Are the plugs you are using the correct heat range? I believe that Don has some listed that run a little hotter than the Champion J12 plugs.

Mike
Reply With Quote
  #3   IP: 72.250.107.144
Old 11-21-2006, 07:34 AM
jhwelch's Avatar
jhwelch jhwelch is offline
Senior Member
 
Join Date: Dec 2005
Posts: 478
Thanks: 0
Thanked 1 Time in 1 Post
I had a bad case once of fouled plugs when my choke stayed closed
even after I had pushed in the handle to the open position after
starting the motor. It should be pretty easy to take the air filter/
backflame arrestor off and look inside the carb. throat to make sure
your control cable is operating properly.

-jonathan
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fouled plugs Enigmalk2 Troubleshooting 11 10-03-2018 10:05 AM
more fouled plugs bill wright Troubleshooting 3 12-15-2005 09:32 AM


All times are GMT -4. The time now is 01:46 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2018 Moyer Marine Inc.

All Rights Reserved