Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 47.16.178.29
Old 05-26-2019, 08:44 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Engine stalls when throttle returns to idle

I am having the following issue with my engine now. It starts fine and idles ok between 1000 and 1100 rpm. This was the case all last season and at some point I'd like to figure out how to make it idle closer to 800 rpm, but this is not a current issue. When I open throttle the engine accelerates fine. However when I bring throttle back to idle my engine stalls. Some times if I move throttle slowly the rpm will drop to 800 there is some hesitation after which idle rpm returns to 1000+. I don't know if this is the aftermath of water in the engine issue that I had earlier in the spring:

http://www.moyermarineforum.com/foru...ad.php?t=11059

Today I tried to figure out whats going on, so here is what I tried and some observations.

1. I have good fuel pressure after pump (there is a gauge there).
2. I drained some fuel from the carb and it looks clean.
3. I cleaned up the carburetor and replaced gasket between two halves.

At this point I run engine again and still had the same issue. I also noticed that only large adjustments to the idle screw had any noticeable effects.

4. Checked and cleaned spark plugs. Turned out the gap was about 0.02, which I have adjusted to 0.04. This improved things a bit, but did not eliminate issue completely.

I am hoping someone could help me identify the issue and suggest what I could try next. Any help would be greatly appreciated.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #2   IP: 24.152.132.140
Old 05-26-2019, 08:58 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by Wisakedjack View Post
3. I cleaned up the carburetor and replaced gasket between two halves.
Did you run a small wire through the tiny ports in the carburetor throat to roto-rooter them out?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #3   IP: 47.16.178.29
Old 05-26-2019, 09:36 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Yes I did.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #4   IP: 24.152.132.140
Old 05-26-2019, 09:38 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
PCV system?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #5   IP: 47.16.178.29
Old 05-26-2019, 10:01 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I did put PCV from Indigo in place 2 seasons ago and it seemed to work well. I did not think about it...
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #6   IP: 24.152.132.140
Old 05-26-2019, 11:08 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
As a test try plugging the vacuum hose.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #7   IP: 97.93.70.7
Old 05-27-2019, 09:45 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Did you check to see that the C-advance was functioning nicely?

When replacing the bowl gasket did you check between the halves of the carb for warpage? This warpage can cause idle problems if the emulsion well in the center is not sealed!

Are you sure it isn't the throttle linkage holding the carb off of the idle stop? Worth a check.

Dave Neptune
Reply With Quote
  #8   IP: 47.16.178.29
Old 05-27-2019, 01:35 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Dave what is C advance? Are you talking about timing? If thats the case then no I did not change anything with ignition. I went to the boat today and tried the test that Neil has suggested. I had a helper holding a thumb to close hose that we have disconnected from the PCV valve. Still had the same issue. PCV valve rattles, so I don't think its stuck. As far as the carburetor is concerned I was looking for a vacuum leak, which is why I changed the gasket between halves. Old one did look somewhat warped. Dave, what did you mean when you said that:

"the throttle linkage holding the carb off of the idle stop"

How do I check for that? I looked at MM manual and only suggestions I am seeing are basically to clean up carburetor. Given my water intrusion earlier dirt in the carburetor is possible, but I've cleaned it after twice (one full and one partial). I wonder if anything else could be at play here. I really liked the possibility that it was caused by PCV, but I think my test ruled it out, right? That would have been a really easy fix
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #9   IP: 68.0.42.244
Old 05-27-2019, 02:54 PM
indigo indigo is offline
 
Join Date: Jun 2007
Location: Williamsburg, VA
Posts: 54
Thanks: 8
Thanked 54 Times in 28 Posts
Vacuum Leak

Now that you have ruled out the PCV valve itself, try carefully squirting a little starting fluid around the two gasketed joints on the PCV spacer plate with the engine idling. If the engine speed changes when squirting, then there is a vacuum leak in one of the joints. You might also squirt a little around the throttle shaft where it enter the carb body to check the shaft seal.

Tom
Reply With Quote
  #10   IP: 47.16.178.29
Old 05-27-2019, 03:06 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I don't know whether this may be at play here... I've noticed that MM carburetor rebuild kit contains what look like rubber gaskets. I don't recall seeing any in my carburetor when I cleaned it. But I had this engine for almost 5 years now and it worked well before. I am just curious now whether gaskets are needed? Are there ones that go on the throttle lever shaft by any chance?
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #11   IP: 24.152.132.140
Old 05-27-2019, 04:09 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by Wisakedjack View Post
I went to the boat today and tried the test that Neil has suggested. I had a helper holding a thumb to close hose that we have disconnected from the PCV valve. Still had the same issue.
Good test, eliminates one possibility. Just to confirm, the hose you plugged was the one that connects to the spacer between the carburetor and manifold, correct?

If you bought the Zenith factory carb kit (a recent addition to the catalog by the way), the small black rubber donuts are throttle and choke shaft seals.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 05-27-2019 at 04:26 PM.
Reply With Quote
  #12   IP: 47.16.178.29
Old 05-27-2019, 05:21 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Quote:
Originally Posted by ndutton View Post
Good test, eliminates one possibility. Just to confirm, the hose you plugged was the one that connects to the spacer between the carburetor and manifold, correct?
Yes, thats the one we plugged - one that connects to the aluminum spacer.

Quote:
Originally Posted by ndutton View Post
If you bought the Zenith factory carb kit (a recent addition to the catalog by the way), the small black rubber donuts are throttle and choke shaft seals.
Good to know. I've not bought the carb kit recently, but I looked at the picture and wondered what those rubber gaskets are for since I've not encountered any in my own carburetor. I don't know if its time to rebuild yet. I cleaned my carburetor every fall after the haul out and it does look pretty clean. I will do the tests that Tom has suggested to see whether there is a vacuum leak at the flange or the shaft.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #13   IP: 47.16.178.29
Old 05-27-2019, 08:23 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I should have mentioned one more detail. When cleaning my carburetor I was not able to remove an idle jet. The slot shows some minor damage. The MM manual said its better to leave it in place, which I've been doing for years now. I blasted it with carb cleaner and compressed air. I guess I will only need to worry about its removal if I have to rebuild using MM kit. But I would be curious to know how to do it without damaging the carburetor itself.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #14   IP: 98.125.73.7
Old 05-27-2019, 11:36 PM
capnward's Avatar
capnward capnward is offline
Afourian MVP
 
Join Date: Aug 2012
Location: Deer Harbor WA
Posts: 335
Thanks: 41
Thanked 147 Times in 107 Posts
no idle? check idle jet.

You're right, you should have mentioned that. I once had a problem that the engine wouldn't idle. I couldn't see that the idle jet was partially obstructed until I removed it, held it up to the light, and looked through it. It has been recommended that you file a screwdriver to just the right size for the idle jet, so you won't damage it. It should come out, but if you can't do that, run a thin wire from a wire brush around in it, while it's in the carb. Don Moyer showed that wire trick in his superb video, after removing the jet from the carb. The junk in it may not dislodge with carb cleaner or air. That tiny orifice is so important to keep clean. If there is junk in your fuel, the idle jet will be the most likely place in the carb to catch it. If the opening of it is really mangled, I guess that may affect it as well. Once the jet was clear, the idle came back. Now I take it out every year and check it for crud. That to me is the most important part of carburetor cleaning.
Now I know that there are supposed to be rubber seals around the throttle and choke shafts. I haven't noticed them before. I wonder if I have them...
Reply With Quote
  #15   IP: 47.16.178.29
Old 06-02-2019, 05:47 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Here is a quick update on my issue. I sprayed some starter fluid around the carburetor (throttle shaft, between two halves and around manifold) and did not get any increase in RPM. I had new gaskets put earlier, so for me only the shaft was a suspect. I brought carburetor home and will clean it again with special attention paid to the idle jet (thanks capnward). Will let you guys know what happens when I fire the engine again. In the meantime any other suggestions on what I could try or test would be greatly appreciated.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #16   IP: 99.30.185.198
Old 06-02-2019, 10:02 PM
thatch thatch is online now
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Wisakedjack, Sorry it took so long for the light to finally come on, but, since we're dealing with a Catalina-30 here, you may have a vacuum leak at the back end of the manifold. Here's how it goes. The hot section of a c-30's exhaust runs laterally from the manifold over to the top of the water-lift/muffler, where it drops down and connects, normally with a short length if rubber hose, to the inlet on the top. Engine torque, over time, tends to either crack the water-lift or to loosen up or actually crack the flange at the back of the manifold. Neil and I replaced a manifold on an A4 a couple of years ago that had completely cracked off. The manifold had rusted through and the crack went undetected until after it was removed. Recently I rebuilt my hot section and replaced my manifold because of a crack in the flange area. One way to check for a vacuum leak at the manifold gasket is to spray some WD-40 between the head and the manifold while the engine is running. If there is a leak, the engine rpms should change and some white smoke should show up in the exhaust. I realize that you had recently removed the head, but didn't notice if you removed the manifold or not.
Tom
Reply With Quote
The Following User Says Thank You to thatch For This Useful Post:
lat 64 (06-03-2019)
  #17   IP: 47.16.178.29
Old 06-02-2019, 11:42 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
Tom, thanks for the suggestion. I did not remove the manifold. I will look at the manifold flange and do the test that you've described.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #18   IP: 47.16.178.29
Old 06-05-2019, 09:51 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I am very happy to report that my carburetor issues have been resolved. While cleaning my carburetor this week I've discovered the following issues:

1. I think the main issue was that the idle screw was not seated completely when I was doing its adjusting. I got the new longer one from MM earlier this season and the fit was pretty tight, so I assumed it was screwed in all the way, when the conical tip was merely showing in the passage opening. In retrospect I should have realized the the spring should be fully compressed when the idle screw is all in. Having done this properly I did 3/4 turn out since I have PCV valve as an initial setting and it pretty much worked well.

2. I carefully cleaned the idle jet with small wire. I was not able to take it off since the screw driver slot is half gone. So, I had to do it in place. By the feel it was not completely clogged, but may have had some residue there.

3. I discovered that choke plate was put incorrectly. As a result the poppet valve was opening to the outside instead of inside. I think that explains why I always needed to open the choke right after the engine was started.

4. Finally, I replaced the throttle plate. The old one was somewhat bent and did not fully obscure the lower of the two idle holes. Whether that had any significant effect on how my carburetor worked I don't know.

After putting carburetor in the engine and minor adjusting I no longer have any issues with engine shutting off when I throttle down. In addition the engine idles nicely at 800 RPM. I don't think it ever sounded this good.

I would like to thank everyone here for advise and helpful suggestions. It was extremely valuable to learn few other possible causes (like PCV valve failure or cracking exhaust flange) even though they were not in play at this time. Thank you guys!
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
The Following 4 Users Say Thank You to Wisakedjack For This Useful Post:
Administrator (06-05-2019), edwardc (06-06-2019), JOHN COOKSON (06-06-2019), thatch (06-05-2019)
  #19   IP: 24.152.132.140
Old 06-06-2019, 06:07 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Check your spring

There were so many different needles and springs used throughout the 4 decades of the late model carburetors that a problem emerges when someone uses an earlier (smaller diameter) spring with one of the later needles.

The proper dimensions are: ID is just under ¼” and the uncompressed length is just over ½”. Turning the factory needle in against the seat, the spring is not quite fully compressed. There is a small shoulder at the outer end of the needle which the spring slips over.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #20   IP: 70.185.132.167
Old 06-06-2019, 08:10 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
I didn't reread the thread.
If you don't have a "polishing filter" between the fuel pump and the carburetor I would strongly recommend one.

TRUE GRIT
Reply With Quote
  #21   IP: 47.16.178.29
Old 06-06-2019, 08:26 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I do have a polishing filter between the pump and the carburetor
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #22   IP: 47.16.178.29
Old 06-10-2019, 03:31 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I did some sea trials this last weekend. Engine does not shut down anymore when I throttle it down. Max RPM at full throttle is close to 2000 now. Opening throttle more has no effect. At full throttle my boat speed was about 5.5 kts, but I had outgoing tide against me. So, its close to hull speed. Makes me very happy! I don't know how I could've done it all without having all your help and access to this awesome community. Thanks a lot guys!
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
  #23   IP: 24.152.132.140
Old 06-10-2019, 04:02 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Did you ever find out why the idle mixture needle didn't seat properly the first time?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #24   IP: 47.16.178.29
Old 06-10-2019, 05:52 PM
Wisakedjack's Avatar
Wisakedjack Wisakedjack is offline
Senior Member
 
Join Date: May 2015
Location: New Jersey
Posts: 118
Thanks: 19
Thanked 29 Times in 16 Posts
I did not want to apply too much force and thought it was seated. I should have realized that I was wrong since spring was barely compressed. When I realized my mistake half a turn with screwdriver pushed it in from which point turning it rest of the way was easy.
__________________
Alex
1976 Catalina 30
Perth Amboy, NJ
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Engine only runs at idle with full choke GMcK106 Fuel System 16 05-07-2013 09:01 AM
Request advice with stalling engine Jon K Troubleshooting 20 09-02-2012 09:45 AM
Good Problem Jimmy General Interest 6 05-14-2012 10:04 PM
Engine stalls if throttled down quickly Baltimore Sailor Troubleshooting 12 01-04-2009 05:35 AM
Removing the engine from your boat Don Moyer General Interest 13 06-27-2008 11:06 AM


All times are GMT -4. The time now is 01:41 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved