Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Electrical

Reply
 
Thread Tools Display Modes
  #1   IP: 173.76.51.176
Old 05-04-2019, 08:20 PM
tmcdonagh tmcdonagh is offline
Senior Member
 
Join Date: Oct 2017
Location: Buzzards Bay
Posts: 18
Thanks: 14
Thanked 1 Time in 1 Post
If sparkplugs could talk

Now that I am close to retirement, I have decided to take on tasks I thought I did not have the time for as a busy working slob. I tacked the gas filter and oil change. I barely avoided creating a superfund site with both operations. I then took on the spark plug change out. It was a crusty nasty mess but I did not break any on the way out. Please see the pictures of the business end of the plugs. They are arranged from 1 through 4. The last two picks are of 1 then 4. What are your thought?
A little history, she has been inning a bit rough this last year with the engine cutting out unexpectany and has been a rough starter.

Thoughts?

Tom
Attached Images
   
__________________
S/V SERVUS
Tartan 30
Hull number 513
Reply With Quote
  #2   IP: 72.69.36.126
Old 05-04-2019, 09:21 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
I'm not an expert on spark plugs but what those tell me is that (1) you have had water in your engine room that has rusted the outside of the plugs (ie, that rust could be an engine problem if it is the head that has leaked that water), (2) the first two plug tips look just about a perfect "toasty" brown, and (3) it is not unusual for the last two plugs to show signs of a richer mix.

So my read would be that you need new plugs, make sure the plug wells are free from water, and probably look to the carb, fuel, or ignition for causes of ill-running.
Reply With Quote
The Following 2 Users Say Thank You to tenders For This Useful Post:
chapster5 (05-05-2019), tmcdonagh (05-05-2019)
  #3   IP: 97.93.70.7
Old 05-07-2019, 11:10 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Red face Talking plugs

Tom, the plugs don't actually talk but they do leave clues to be read.

First, the lack of color on the electrode porcelain indicates a plug whose "heat range" is to hot as there is very little deposited, dark or light. A cooler plug will make more power, run smoother and allow deposits to coat the ceramic which is nothing more than a heat sink.

The darker color on the ground indicates a pour burn inside the cylinder. This poor burn most likely is the timing is to far advanced.

The color that shows is OK for "economy" however more power and cooler running engine needs a bit more color like Jerry mentioned.

Try a set of stock range plugs for a couple of hours and take another "read" of the color. You want to see the beige~tan on the porcelain and about the same on the ground albeit a bit darker. Set the gap to .030 with points and if you run an EI go to at least .035/. The additional gap will idle smoother and start faster too, a big advantage of the EI systems.

Do you know if the plugs shown are in the same heat range or did you go hotter for some "fix-it" reason?

When installing the plugs give the entire outside of the plug a thin coat of dielectric silicone. This aids in both rust prevention and heat transfer through the boots by maintaining "contact' for good heat transfer and the boots won't tear when removing.

NOTE the boots are a big part of the "heat sink" equation related to plug running temps.

Dave Neptune
Reply With Quote
The Following 4 Users Say Thank You to Dave Neptune For This Useful Post:
Administrator (05-07-2019), GregH (05-07-2019), RobH2 (05-07-2019), tmcdonagh (05-15-2019)
  #4   IP: 50.242.183.42
Old 05-07-2019, 04:49 PM
RobH2's Avatar
RobH2 RobH2 is offline
Senior Member
 
Join Date: Dec 2009
Location: Baltimore, MD
Posts: 320
Thanks: 5
Thanked 11 Times in 7 Posts
Awesome info Dave...!
__________________
Rob--

"Who is staring at the sea is already sailing a little."

1968 C&C Invader 36' / Late Model Atomic4
https://www.tumblr.com/sherloch7

Reply With Quote
  #5   IP: 165.89.114.112
Old 05-07-2019, 05:40 PM
tmcdonagh tmcdonagh is offline
Senior Member
 
Join Date: Oct 2017
Location: Buzzards Bay
Posts: 18
Thanks: 14
Thanked 1 Time in 1 Post
Cool

Quote:
Originally Posted by Dave Neptune View Post
Tom, the plugs don't actually talk but they do leave clues to be read.

First, the lack of color on the electrode porcelain indicates a plug whose "heat range" is to hot as there is very little deposited, dark or light. A cooler plug will make more power, run smoother and allow deposits to coat the ceramic which is nothing more than a heat sink.

The darker color on the ground indicates a pour burn inside the cylinder. This poor burn most likely is the timing is to far advanced.

The color that shows is OK for "economy" however more power and cooler running engine needs a bit more color like Jerry mentioned.

Try a set of stock range plugs for a couple of hours and take another "read" of the color. You want to see the beige~tan on the porcelain and about the same on the ground albeit a bit darker. Set the gap to .030 with points and if you run an EI go to at least .035/. The additional gap will idle smoother and start faster too, a big advantage of the EI systems.

Do you know if the plugs shown are in the same heat range or did you go hotter for some "fix-it" reason?

When installing the plugs give the entire outside of the plug a thin coat of dielectric silicone. This aids in both rust prevention and heat transfer through the boots by maintaining "contact' for good heat transfer and the boots won't tear when removing.

NOTE the boots are a big part of the "heat sink" equation related to plug running temps.

Dave Neptune
Thanks Dave!. Oh, plugs don't talk! I thought they were not listening.

I replaced the plugs with Champion RJ12C's and gapped that @ 0.04 as suggested on the forum. I will go back and remove, regap at 0.03 as I don't have the electronic ignition yet and spray with the dielectric silicone. Are there better spark plug wires for heat dissipation?
The plugs were leftover by the previous owner and I have no knowledge of why they were installed.

After installing a new gas filter and plugs she still runs rough for 1-2 minutes, coughing, stumbling and backfiring. She settles down nicely after that time. If I restart her right away, it runs normally. If she sits for 4-6 hours or overnight, the histrionics return. I have not been able to pressure test her on the water as of yet.

Thanks again!
__________________
S/V SERVUS
Tartan 30
Hull number 513
Reply With Quote
  #6   IP: 73.19.60.36
Old 05-11-2019, 12:00 AM
Boat Boat is offline
Senior Member
 
Join Date: Aug 2014
Location: Kirkland, WA
Posts: 172
Thanks: 1
Thanked 14 Times in 13 Posts
your timing looks off to me.
__________________
'69 Newport 30 MKI Hull #20
Reply With Quote
  #7   IP: 165.89.114.112
Old 05-13-2019, 11:12 AM
tmcdonagh tmcdonagh is offline
Senior Member
 
Join Date: Oct 2017
Location: Buzzards Bay
Posts: 18
Thanks: 14
Thanked 1 Time in 1 Post
The Saga continues..

Returned to the boat this weekend armed with all the suggestions and best wishes.
Here's what I did.

Tested compression on all cylinders and they all checked out at ~90 PSI.
Re-gapped spark plugs from 0.04 to 0.03 as suggested.
Injected an ounce or two of MMO into each cylinder and allowed to sit for 30 minutes after a few engine cycles.

Engine stated very rough after 10-15 attempts. Coughed, backfired and sputtered for 2 minutes and would not tolerate choke without stalling. After the 2 minutes or so she settled in and I could run the throttle up to max with no problem. Exhaust smoke was minimal but there seemed to be a bit more oil in the water than I generally notice. Applying a load to the engine by putting it into forward gear caused the engine to cough, backfire, sputter and stall.

I pulled the spark plugs and found plugs 1 and 3 carbonized and sooted while 2 & 4 were clean.

No Joy.

Any suggestions?

Thanks, Tom
__________________
S/V SERVUS
Tartan 30
Hull number 513
Reply With Quote
  #8   IP: 70.185.132.167
Old 05-15-2019, 12:03 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by tmcdonagh View Post
After installing a new gas filter and plugs she still runs rough for 1-2 minutes, coughing, stumbling and backfiring. She settles down nicely after that time. If I restart her right away, it runs normally. If she sits for 4-6 hours or overnight, the histrionics return. I have not been able to pressure test her on the water as of yet.
Thanks again!
This sure sounds like a sticky valve(s) to me. If you were able to run the engine at cruise RPM for an hour it might unstick it. Do you use MMO in your gas? Some* recommend outboard motor oil in the gas to unstick valves. I don't know the exact recipe.
*I think it was Dave N.

TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
tmcdonagh (05-15-2019)
  #9   IP: 173.76.218.50
Old 05-15-2019, 06:25 AM
tmcdonagh tmcdonagh is offline
Senior Member
 
Join Date: Oct 2017
Location: Buzzards Bay
Posts: 18
Thanks: 14
Thanked 1 Time in 1 Post
Quote:
Originally Posted by JOHN COOKSON View Post
This sure sounds like a sticky valve(s) to me. If you were able to run the engine at cruise RPM for an hour it might unstick it. Do you use MMO in your gas? Some* recommend outboard motor oil in the gas to unstick valves. I don't know the exact recipe.
*I think it was Dave N.

TRUE GRIT
Hi John,

I treated the cylinders for about 1/2 hour with MMO and noted no improvement. I did not try it as a gas treatment as of yet. Thanks, it is now on my list.

Tom
__________________
S/V SERVUS
Tartan 30
Hull number 513

Last edited by tmcdonagh; 05-15-2019 at 06:28 AM. Reason: Spelling error correction
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Care to 'talk story'? ndutton Introductions 32 05-10-2019 09:33 PM
Prop talk - final obsessive moment Skywalker Drive Train / Propellers 22 05-23-2015 08:21 AM
Talk me off the ledge! Skywalker General Interest 20 04-20-2013 06:43 PM
What does this mean? (Sparkplugs) TomG Troubleshooting 5 06-03-2011 02:07 PM
Sparkplugs Mark S Ignition System 1 12-12-2009 09:24 AM


All times are GMT -4. The time now is 07:57 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved