Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Interest

Reply
 
Thread Tools Display Modes
  #1   IP: 69.245.172.243
Old 01-10-2010, 01:58 PM
greybeard50 greybeard50 is offline
Member
 
Join Date: Jan 2010
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Dimensions & Weight?

New here... I've tried (and failed) to bring this info up thru searches of the FAQ & Gen Forums. Point me to where this info is archived & I will be grateful.

I need to understand the LxWxH & weight of the A-4 to see if it would work in a smaller powerboat. Pics with a ruler laying on the motor would be a great help.

TIA! Richard Johnson Peru, Indiana on the banks of the Wabash...
Reply With Quote
  #2   IP: 206.125.176.3
Old 01-11-2010, 11:04 AM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Post

HI Richard, Welcome to the forum. This information is archived in several places on the web..one place is the C&C owner's site. - http://cncphotoalbum.com/atomic4/atomic4specs.htm
I think this is the basic info you are looking for:

Maximum operating angle 15°

Length overall UJ: 26 ¾ in, UJR: 31 15/16 in, UJVD: 35 13/16 in

Height above crankshaft centreline 13.125 in

Maximum width 18.250 in

Offset – crankshaft to propeller shaft UJ: 0 in; UJR: 1.042 in; UJVD: na

Base depth below centreline 6 in

Weight UJ: 310 lb; UJR: 330 lb; UJVD: 335 lb

Models
5101 / UJ - base configuration Atomic Four

5111 / UJS - Stevedore configuration for Canadian market, power limited to 15 hp with intake manifold restriction)

5102 / UJR - reduction gearbox mounted on transmission, 2.04 ratio standard

5112 / UJSR - Stevedore configuration with reduction gearbox mounted on transmission, 2.04 ratio standard

5103 / UJVD - 20° angle Walter V drive gearbox mounted on transmission, 4 gear ratio options including 1:1

5113 / UJSVD - Stevedore configuration with 20° angle Walter V drive gearbox mounted on transmission, 4 gear ratio options including 1:1
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #3   IP: 69.232.227.128
Old 01-11-2010, 02:41 PM
SeaFever SeaFever is offline
Senior Member
 
Join Date: Dec 2009
Posts: 45
Thanks: 0
Thanked 2 Times in 2 Posts
Hi Richard,

I have scanned and attached the page from the Atomic 4's spec sheet that provides the dimensions.

Hope that helps.
Attached Images
 
Reply With Quote
  #4   IP: 71.65.36.129
Old 01-12-2010, 04:18 PM
greybeard50 greybeard50 is offline
Member
 
Join Date: Jan 2010
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Dims & Wt Found!!!

Perfect....This engine must be solid...I do not think a Chevy small block weighs 300 lb

OK, now for the weight & balance calcs....I'm going to be busy for awhile....

rwj
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Bed dimensions bcooke General Interest 4 11-18-2009 06:53 AM
Short block weight lat 64 Overhaul 10 10-24-2008 01:56 PM
side plate bolt dimensions m_galligan Cooling System 0 07-30-2007 01:03 AM
Thermostat dimensions Walter Pearson Cooling System 3 06-06-2005 07:38 AM


All times are GMT -4. The time now is 10:08 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved