Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Polls

View Poll Results: What is the steady state temperature of your engine?
120 degrees or below 20 9.22%
130 degrees 12 5.53%
140 degrees 39 17.97%
150 degrees 17 7.83%
160 degrees 59 27.19%
170 degrees 29 13.36%
180 degrees or higher 41 18.89%
Voters: 217. You may not vote on this poll

Reply
 
Thread Tools Display Modes
  #1   IP: 38.102.24.232
Old 05-27-2009, 10:04 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
What temperature?

At Jonathan Welch's suggestion, here's an opportunity to participate in a poll regarding your engine's temperature when fully warmed up.

Bill
Reply With Quote
The Following User Says Thank You to Administrator For This Useful Post:
Capngeo (07-02-2020)
  #2   IP: 70.90.87.69
Old 05-27-2009, 11:01 AM
Jesse Delanoy Jesse Delanoy is offline
Afourian MVP
 
Join Date: Dec 2006
Posts: 236
Thanks: 0
Thanked 2 Times in 2 Posts
y'know, it's funny sometimes ...

When I bought my '77 Catalina 30, with original RWC A4, 9 years ago, it ran pretty consistently around 180 warmed up, under load. Not so hot as to be problematic, but hotter than I would like. I tried everything I could think of. Pressure flushes. Acid flush. Opened up the side plate and cleaned out the gunk. Put a restriction on the bypass. One season, on advice of a local mechanic, I blocked off the bypass entirely. Replaced the thermostat. All with no results.

Three seasons ago, the old girl finally gave up the ghost, and I installed a Moyer rebuilt replacement engine. I thought, finally, I'll be operating at the desired temperature. No such luck. Still running right around 180.

Along with many other projects along the way, I undertook to replace the three mismatched gauges on my instrument cluster. The gauges (and associated sending units) of course did not get replaced with the engine - my mechanic simply installed the old ones on the new engine. The oil pressure gauge and ammeter went in quite easily, but I COULD NOT GET the old temperature sending unit out of the cylinder head. It was stuck in, absolutely fast. I tried with every vise grip I could get my hands on, and succeeded only in wearing the hex-head on the sending unit down to a near perfect circle. I gave up on it for about a year and a half, and just lived with the old gauge.

This spring, during re-commissioning, I was thinking about having the old sending unit drilled out - not sure if this was possible since there's only about 3 inches of space between the front of the engine and the front of the engine compartment (access is from the top down). But I had the engine warmed up during an acid flush, and wondered if I could get the sender out while everything was nice and hot. I put a vise grip on it as tight as I could possibly muster, and whacked it about three times with a rubber mallet, and sonofagun if it didn't loosen right up. I was thrilled.

Anyway, to make a long story short (I know ... too late!), I put in the new sending unit and temperature gauge I'd been sitting on for a year and a half, and guess what? Engine is now running consistently at 160 - 165 under load.

I'm guessing there was a long-standing mismatch of temperature gauge and sending unit - the original SW gauge had been replaced with a cheapo at some point prior, and I bet the sending unit had never been touched. These two items must be matched up, or the gauge readings are suspect. I spent eight years worrying about an engine that probably was never overheating.
Reply With Quote
  #3   IP: 68.224.125.99
Old 05-27-2009, 11:45 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
160º at 1700rpm in calm water at 5.5k. (Oil at 40psi)

Last edited by roadnsky; 05-28-2009 at 10:37 PM. Reason: Add oil pressure reading and correct rpms
Reply With Quote
  #4   IP: 206.40.166.218
Old 05-27-2009, 01:01 PM
Mark S's Avatar
Mark S Mark S is offline
Senior Member
 
Join Date: Sep 2008
Location: Marblehead MA
Posts: 421
Thanks: 0
Thanked 2 Times in 2 Posts
I answered the poll "160 degrees" based on what our gauge read last year when it was operating. I still haven't got it working this spring. I think the engine is operating a little cooler now than last year, based on what it feels like when I touch it, because of some off-season improvements and maintenance: (1) I cleaned the thermostat which was really ugly; (2) I installed the by-pass valve which I close when I think the engine ought to be warmed up; and (3) I gave it two vinegar flushes. Of course it could simply be a five to ten degree difference in May and September ocean temperatures.

Mark S
Reply With Quote
  #5   IP: 142.68.243.164
Old 05-27-2009, 04:15 PM
rigspelt's Avatar
rigspelt rigspelt is offline
Afourian MVP
 
Join Date: May 2008
Posts: 1,187
Thanks: 0
Thanked 19 Times in 17 Posts
Quote:
Originally Posted by Jesse Delanoy View Post
...wondered if I could get the sender out while everything was nice and hot. I put a vise grip on it as tight as I could possibly muster, and whacked it about three times with a rubber mallet, and sonofagun if it didn't loosen right up. I was thrilled.
That really is one sweet feeling of relief. Happened the other night with a throughull that finally turned out.
__________________
1974 C&C 27
Reply With Quote
  #6   IP: 71.118.13.238
Old 05-27-2009, 04:19 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Red face Too cool 130 degrees??

I have been using a valve in the bypass line for 26 years now on a raw water cooled application. Yes I do run a bit cold (130 degrees) however I run easy until the temp has come up, after that I run at 2000 RPM's with the Indigo 3-blade.
One thing I do check is when I turn off the A-4 after a long run I switch the ignition back on after about 4-5 minutes and she reads about 140~150 degrees which is approximately what the core of the engine is actually running at. I think the water bypassing the block cools the "thermostat corner of the head" just a bit affecting the reading on the gage when not using a thermostat.

Dave Neptune
1970 E-35MkII original A-4 still "ticking"
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
AFisch (04-20-2020), TimBSmith (10-02-2020)
  #7   IP: 64.193.4.74
Old 05-27-2009, 04:58 PM
Capn Tom's Avatar
Capn Tom Capn Tom is offline
Senior Member
 
Join Date: Jun 2008
Location: On the boat
Posts: 11
Thanks: 0
Thanked 0 Times in 0 Posts
what temperature?

I've got one for "me hardys"! A previous owner (#1 or #2) removed the thermostat. He ran a hose from the t-fitting that's supposed to run to the t-stat and instead ran it to the manifold. The hose also has an on-off valve in it. I assume he had overheating problems and thought this was a solution? I don't use the hose in the on position.
My engine used to run up to 160; sometimes a little higher until I acid flushed. It then started running at 110. I always flush the engine with fresh water after using it (it is raw water cooled) to get rid of any salt.
Sidenote: Last week I replaced the riser because corrosion ate right through it.
Should I leave it alone or put back in a t-stat?
__________________
Cap'n Tom

Live NOW or die a SLOW death; Live your dreams, don't dream your life.
Reply With Quote
  #8   IP: 69.251.211.217
Old 05-27-2009, 09:22 PM
MikeB.330's Avatar
MikeB.330 MikeB.330 is offline
Senior Member
 
Join Date: Jun 2006
Posts: 247
Thanks: 0
Thanked 4 Times in 4 Posts
between 170 and 180 just like a freshy should.
Reply With Quote
  #9   IP: 64.231.127.244
Old 05-27-2009, 09:42 PM
67c&ccorv's Avatar
67c&ccorv 67c&ccorv is offline
Afourian MVP
 
Join Date: Dec 2008
Location: London, ON
Posts: 1,559
Thanks: 4
Thanked 9 Times in 9 Posts
[QUOTE=Jesse Delanoy;14474]The oil pressure gauge and ammeter went in quite easily, but I COULD NOT GET the old temperature sending unit out of the cylinder head. It was stuck in, absolutely fast. I tried with every vise grip I could get my hands on, and succeeded only in wearing the hex-head on the sending unit down to a near perfect circle. I gave up on it for about a year and a half, and just lived with the old gauge.

"Firstly, vice grips are not for removing nuts or bolts - they are a last ditch attempt when a proper fitting wrench or socket is not at hand and you absolutely must remove the bolt/nut. Try gently heating the area around the bolt or thread with a propane torch and then put some effort on a proper fitting wrench."

This spring, during re-commissioning, I was thinking about having the old sending unit drilled out - not sure if this was possible since there's only about 3 inches of space between the front of the engine and the front of the engine compartment (access is from the top down). But I had the engine warmed up during an acid flush, and wondered if I could get the sender out while everything was nice and hot. I put a vise grip on it as tight as I could possibly muster, and whacked it about three times with a rubber mallet, and sonofagun if it didn't loosen right up. I was thrilled...I'm guessing there was a long-standing mismatch of temperature gauge and sending unit - the original SW gauge had been replaced with a cheapo at some point prior, and I bet the sending unit had never been touched. These two items must be matched up, or the gauge readings are suspect. I spent eight years worrying about an engine that probably was never overheating.

"Yes, gauges and their senders must be matched or the readings will be innacurate!"

1967 early model Atomic 4 with Dole thermostat runs steady 140 degrees on Great Lakes freshwater after warmup on my C&C Corvette.

Last edited by 67c&ccorv; 05-27-2009 at 09:45 PM.
Reply With Quote
The Following User Says Thank You to 67c&ccorv For This Useful Post:
TimBSmith (10-02-2020)
  #10   IP: 206.125.176.3
Old 05-28-2009, 08:57 AM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
oil pressure poll?

Hi Bill,

Great idea..I also like roadnsky's additional details for his particular situation provided.

Here's mine: 160-165 at 1,500 RPM. For now that's my 'favorite cruising speed'. The speedo says 4.6 knots , but it is new and not calibrated.

What about a similar poll for typical oil pressure? I dunno how well that would work since that reading probably fluctuates moreso than temp, but I would assume most have a 'standard range' they see at their favorite cruising speed which could be detailed in a topic reply after the poll entry.

Edit - update time.

So, now that I have been using the boat a little more I have been experimenting with the bypass lever.

With it wide open, I am closer to that 165 F & it fluctuates a bit...it'll go above 170F and then down to 160. When I close the bypass all the way, it is much more stable at 155-160F, but I also notice not as much exhaust flows out of the pipe either. I would assume this is because until the thermostat opens, only the small amount of water sneaking thru the closed t-stat is making its way to the exhaust. Is there any other place water can get to the manifold besides thru the t-stat bypass or the t-stat itself?
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 08-25-2009 at 03:07 PM. Reason: update
Reply With Quote
  #11   IP: 70.211.215.130
Old 05-28-2009, 08:55 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Thumbs up

Got it, Shawn!

Bill
Reply With Quote
  #12   IP: 98.216.118.140
Old 05-29-2009, 08:36 PM
bcooke's Avatar
bcooke bcooke is offline
Senior Member
 
Join Date: Mar 2005
Location: Rowley, MA
Posts: 38
Thanks: 0
Thanked 0 Times in 0 Posts
My understanding is that raw water cooling is usually around 180 and freshwater cooling is around 160.

Does that sound about right?

My freshwater cooled A4 runs right at 160 no matter what sort of load its under.

Last edited by bcooke; 05-29-2009 at 08:42 PM.
Reply With Quote
  #13   IP: 68.34.11.142
Old 06-03-2009, 08:20 AM
MikeB.330's Avatar
MikeB.330 MikeB.330 is offline
Senior Member
 
Join Date: Jun 2006
Posts: 247
Thanks: 0
Thanked 4 Times in 4 Posts
bcooke, you have that backwards. 160 for sea water cooled and 180 for fresh water cooled is what you're looking for. Your's is a bit cool for a fresh water cooled engine. Are you sure you have the correct Tstat instaled?

Last edited by MikeB.330; 06-03-2009 at 08:22 AM.
Reply With Quote
  #14   IP: 199.246.2.9
Old 06-20-2009, 09:25 AM
alberg alberg is offline
Senior Member
 
Join Date: Dec 2007
Posts: 30
Thanks: 0
Thanked 0 Times in 0 Posts
Water Temp

At operating RPM's of 1550 my temp is 145 deg on my VDO matched 4 gauge unit. However after running and then idleing it drops to 100 deg.

Alberg
Reply With Quote
  #15   IP: 72.73.119.232
Old 08-03-2009, 09:34 PM
ne57301 ne57301 is offline
Senior Member
 
Join Date: Oct 2006
Location: Maine
Posts: 36
Thanks: 0
Thanked 1 Time in 1 Post
I'm still getting used to the cleaned out engine.

My raw water cooled used to run at around 180-190 with frequent spikes, back off the throttle and it would cool right down. Now it stays pretty solid at 155-165 except a MAJOR spike a week ago. I limped the last .5 mile of a 30 mile delivery (wow was that lucky!!) and when I went back to troubleshoot it was fine. I figure after all the cleaning I did last winter a piece of scale wedged somewhere unfortunate (manifold exit?) and settled again when it was shut down for a while. I'll continue to watch the gauge - and for steamy exhaust.
Reply With Quote
  #16   IP: 24.5.199.134
Old 08-04-2009, 02:04 AM
tony201's Avatar
tony201 tony201 is offline
Senior Member
 
Join Date: Jan 2009
Location: Rodeo Calif.
Posts: 40
Thanks: 0
Thanked 0 Times in 0 Posts
Mine stays at 70 at 1900 giving 5.9
Reply With Quote
  #17   IP: 138.88.80.7
Old 09-10-2009, 10:56 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Quote:
Originally Posted by ne57301 View Post
I'm still getting used to the cleaned out engine.

My raw water cooled used to run at around 180-190 with frequent spikes, back off the throttle and it would cool right down. Now it stays pretty solid at 155-165 except a MAJOR spike a week ago. I limped the last .5 mile of a 30 mile delivery (wow was that lucky!!) and when I went back to troubleshoot it was fine. I figure after all the cleaning I did last winter a piece of scale wedged somewhere unfortunate (manifold exit?) and settled again when it was shut down for a while. I'll continue to watch the gauge - and for steamy exhaust.
Uh Oh...good luck with the troubleshooting, dude!
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #18   IP: 142.68.251.234
Old 09-13-2009, 05:55 AM
rigspelt's Avatar
rigspelt rigspelt is offline
Afourian MVP
 
Join Date: May 2008
Posts: 1,187
Thanks: 0
Thanked 19 Times in 17 Posts
Still getting used to this FWC A4. Yesterday noticed while at cruising speed for first time that temp was 175 but dropped to 165 when I sent crew forward to bring exhaust outlet up clear of the water surface. It is well clear at lower speeds and sailing. Boat squats and acquires a stern wave when running at full cruising speed, so need to shift weight forward or drop RPMs a bit. Example of backpressure, maybe? Lowering RPM does not sacrifice too much speed.

Turns out lower stern is typical for C&C 27 fitted with wheel pedestal and A4. Helps to switch from the Mark I/II scimitar rudder to the lighter/longer Mark III rudder, and maybe from wheel to tiller. Hmm.
__________________
1974 C&C 27

Last edited by rigspelt; 09-13-2009 at 07:19 AM.
Reply With Quote
  #19   IP: 75.196.176.36
Old 09-18-2009, 06:11 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Rigsy:

Don and I had a discussion about this a few years ago. His view was that the back pressure generated by the exhaust being underwater (at a depth within reason) was trivial. The engineer in me had to run the numbers. I forget exactly how the calculations came out, but as usual he was correct. In fact, some boats are designed this way.

Of course, if you're on the edge of a problem, I suppose you could see a performance effect, but my guess is that what you're seeing by moving the crew around has more to do with changing the hydrodynamics of the boat than back pressure.

Bill
Reply With Quote
  #20   IP: 142.68.249.245
Old 09-18-2009, 06:16 PM
rigspelt's Avatar
rigspelt rigspelt is offline
Afourian MVP
 
Join Date: May 2008
Posts: 1,187
Thanks: 0
Thanked 19 Times in 17 Posts
Bill - thanks for that info. I doubt anything significant is going on, not after all the work last winter. Just settling in.
__________________
1974 C&C 27
Reply With Quote
  #21   IP: 173.166.26.245
Old 07-03-2010, 10:34 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
exhaust in the water

I must disagree with the notion that having exhaust partly under water does not affect performance. When I raised my transom exit 5" in response to this issue I got and immediate and noticable improvement in performance and economy.
Reply With Quote
  #22   IP: 161.213.49.1
Old 07-28-2010, 05:26 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Don't Always Believe What Temp You See On The Gauge!!!!

1. A4 was running at a temp of 180-190. (RWC)
2. Rebuilt the entire cooling system including new temp gauge and sending unit. Had excellent water flow out the back of the exhaust manifold.
3. A4 still running at a temp of180-190.
4. Rewired boat and engine.
5. A4 now running at a temp of 140-160. Seems to go through a normal warm up curve.

My theory: (Somebody please comment on this) Excess reisistance, I think it was in the ground circuit, was causing the gauge to read to read higher than the actual temp.

It is easy to check wiring with a jumper wire and an ohm meter. (This is how I found that the wiring had a problem)

Further proof would be to run with the jumper wire(s) in place and see if the gauge readings change.

Last edited by JOHN COOKSON; 07-28-2010 at 05:33 PM.
Reply With Quote
  #23   IP: 24.152.131.220
Old 07-28-2010, 11:13 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Just the Opposite!

Quote:
Originally Posted by JOHN COOKSON View Post
1. A4 was running at a temp of 180-190. (RWC)
2. Rebuilt the entire cooling system including new temp gauge and sending unit. Had excellent water flow out the back of the exhaust manifold.
3. A4 still running at a temp of180-190.
4. Rewired boat and engine.
5. A4 now running at a temp of 140-160. Seems to go through a normal warm up curve.

My theory: (Somebody please comment on this) Excess resistance, I think it was in the ground circuit, was causing the gauge to read higher than the actual temp.
John,
Excess resistance would give you the opposite effect, reading lower than actual. The temperature gauge is little more than a voltmeter with the sender a variable resistor to ground. Zero resistance pegs the gauge at its maximum. The greater the resistance, the lower the gauge reading.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #24   IP: 173.166.26.241
Old 01-08-2011, 01:44 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Quote:
Originally Posted by ndutton View Post
John,
Excess resistance would give you the opposite effect, reading lower than actual. The temperature gauge is little more than a voltmeter with the sender a variable resistor to ground. Zero resistance pegs the gauge at its maximum. The greater the resistance, the lower the gauge reading.
This is a solid reason why every owner should have a direct reading gauge to complement and verify his remote panel instruments.
Reply With Quote
  #25   IP: 173.166.26.241
Old 01-08-2011, 02:52 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Thumbs up

Tom - All your numbers are right on target! I too am interested in entrance and exit temperature differential. I might add that it is worthwhile to monitor entrance temperature with a separate gauge (Or could a switchable gauge with multiple senders be developed? - hint, hint - Wish List) I have never liked the late model thermostat arrangement which is one of the reasons I put an early head on my late engine. Keep up the good work. Regards, Hanley
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Temperature Gauge question Unregistered Cooling System 5 12-28-2010 11:46 AM
Temperature gauge Mark S Troubleshooting 5 05-21-2009 11:09 AM
Temperature Gauge Sending Unit Jesse Delanoy Cooling System 6 10-25-2008 07:41 AM
Erratic temperature gauge HerbertFriedman Cooling System 3 10-14-2007 06:43 PM
Temperature gauge problems? omec Cooling System 0 07-16-2007 12:37 PM


All times are GMT -4. The time now is 03:09 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved