Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 97.83.133.48
Old 05-29-2018, 11:46 AM
China Sea China Sea is offline
Frequent Contributor
 
Join Date: Jun 2017
Location: Madison WI
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Bubbling fluid around spark plugs under load

I know, this sounds strange, but I don't know why this is happening.
We have been trying to solve another issue and this one popped up.

They may be related, so I will tell you about both of them.

Our A4 starts fine and runs for a while (30 minutes at 1500-2000RPM) and then dies.
If we wait for 15 minutes, it will start and fun fine for another 5 minutes, repeat as long as you want.

Last year we had the same problem, but we discovered that if you kept the RPMs below 1200. it would run as long as we needed it (about 1 hour)

Over the winter I rebuilt the carb and the mechanical fuel pump.
Last year I replaced the fuel filter. To take it off the list of possibilities, I will replace it again tomorrow
Any Ideas?

While we were running at 2000RPMs yesterday, I opened the engine hatch to look at the engine and 2 of the "spark plug wells" were full of bubbling fluid (could be boiling water or maybe cooling water with exhaust gasses escaping out of ?
When the engine was running at 1500RPMs or less the "spark plug wells" returned to looking dry.
Background; Great lake 1965 boat, freshwater cooling.
Any ideas whats going on.? Thanks for your advise.

Last edited by China Sea; 05-29-2018 at 11:54 AM.
Reply With Quote
  #2   IP: 108.172.150.97
Old 05-29-2018, 11:50 AM
Marty Levenson Marty Levenson is offline
Senior Member
 
Join Date: Nov 2004
Location: Bowen Island, BC
Posts: 679
Thanks: 91
Thanked 42 Times in 36 Posts
Alternator bracket

Hey China Sea - very likely you have a head leak under the alternator bracket (aka lifting eye). Is the water pooling on the #3 and #4 spark plugs?
__________________
Marty
1967 Tartan 27
Bowen Island, BC

Reply With Quote
  #3   IP: 97.83.133.48
Old 05-29-2018, 01:26 PM
China Sea China Sea is offline
Frequent Contributor
 
Join Date: Jun 2017
Location: Madison WI
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks Marty
yes # 3 and 4.
How is the water getting into the spark plug well?
is that boiling water (overheating) or is that escaping gasses (compression) gasses.?
is this a cracked head or a leaky gasket?

Last edited by China Sea; 05-29-2018 at 01:33 PM. Reason: added thanks
Reply With Quote
  #4   IP: 172.95.97.58
Old 05-29-2018, 02:04 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
China, likely the water is coming up through the threads in the stud this is the easy one. The other is a crack in the head from improper torque on the bracket.

Dave Neptune
Reply With Quote
  #5   IP: 97.83.133.48
Old 05-29-2018, 02:22 PM
China Sea China Sea is offline
Frequent Contributor
 
Join Date: Jun 2017
Location: Madison WI
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Dave, Thanks for the input.
Does that mean either the studs need to be tightened, or a gasket problem, or in option 2, they were over tightened and cracked the head.?

How is the water getting over to the spark plug wells.? Through the gasket? or running over the top. I did not see any water running on the top.

Ill look again when I am out to the boat this friday

Thanks again
Dan
Reply With Quote
  #6   IP: 172.95.97.58
Old 05-29-2018, 03:34 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Dan, if it is a stud leaking it is an easy fix as the head can be left in place. It is basically just resealing the stud and retorquing.

In the above the water runs over the top of the head~~not uncommon.

If the head is cracked it can sometimes be fixed via welding and a resurfacing of the head. Or you may just find one from a member with an extra one and there is always a brand new MMI head .

Dave Neptune
Reply With Quote
  #7   IP: 199.87.177.48
Old 05-29-2018, 03:45 PM
zellerj zellerj is offline
Afourian MVP
 
Join Date: May 2005
Posts: 304
Thanks: 5
Thanked 115 Times in 69 Posts
Your first issue - running for 30 minutes and then dying, is a classic example of a coil going bad. When they get hot, then don't work. Running at lower RPMs keeps the coil cooler, and also letting it sit for 15 minutes cools it off. If you have electronic ignition, which I recommend you get if you don't already have it, then you need a coil from Moyer Marine. Don't just use an automotive ignition coil because they might not have the correct resistance.
__________________
Jim Zeller
1982 Catalina 30
Kelleys Island, Ohio
Reply With Quote
The Following User Says Thank You to zellerj For This Useful Post:
tenders (05-30-2018)
  #8   IP: 97.83.133.48
Old 05-29-2018, 08:20 PM
China Sea China Sea is offline
Frequent Contributor
 
Join Date: Jun 2017
Location: Madison WI
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Dave and Marty, you called it. perfectly
There appears to be a crack in the head (bummer for me) between the #2 and #3 spark plug. When the engine is unloaded and up to 2500 RPMs little droplets start to form along it.

Is there any danger in running the engine this way this summer and replacing the head in the fall.? Or am I destroying more as I run it.

Hi Zellerj
That sounds like that could be it. Ill need to look and see if I get spark from it next time it dies on me this Friday.
Reply With Quote
  #9   IP: 72.194.220.204
Old 05-30-2018, 01:26 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by China Sea View Post
Our A4 starts fine and runs for a while (30 minutes at 1500-2000RPM) and then dies.
If we wait for 15 minutes, it will start and fun fine for another 5 minutes, repeat as long as you want.
Last year we had the same problem, but we discovered that if you kept the RPMs below 1200. it would run as long as we needed it (about 1 hour)
Any ideas whats going on.? Thanks for your advise.
Maybe the fuel tank vent is blocked or partially blocked. To test try running with the fuel fill cap ajar and see if the shutdowns go away.

TRUE GRIT
Reply With Quote
  #10   IP: 97.83.133.48
Old 05-30-2018, 12:42 PM
China Sea China Sea is offline
Frequent Contributor
 
Join Date: Jun 2017
Location: Madison WI
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks for that thought. I was along those lines earlier. As a fuel solution possibility I loosened the cap, rebuilt the carb and fuel pump and took out the additional fuel filter I had installed. Still clonked out after 30 minutes. I think I will put the filter back in, but above the pump this time to keep the screen on the pump from getting clogged.

Tomorrow, it the leftover of the hurricane moves out, I will install a replacement ignition coil and try that out on Friday. Thank you to everyone for ideas.
Dan
Reply With Quote
  #11   IP: 24.108.216.230
Old 05-30-2018, 01:43 PM
Easy Rider's Avatar
Easy Rider Easy Rider is online now
Afourian MVP
 
Join Date: Feb 2007
Location: British Columbia
Posts: 139
Thanks: 231
Thanked 30 Times in 20 Posts
(Is there any danger in running the engine this way this summer and replacing the head in the fall.? Or am I destroying more as I run it.)

You would be taking a big gamble running with a cracked head. It could let go at any time especially if it overheats. I wouldn't even think of leaving the dock unless I was confident the problem was fixed. My advice, find yourself a replacement head and save yourself a lot of time and grief.
__________________
Chuck

71 Ranger 29
Reply With Quote
  #12   IP: 67.186.97.244
Old 05-30-2018, 04:37 PM
Sam Sam is online now
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
Coil is a good place to start and I would replace the condenser. I had the same running/stopping/coolingstarting cycle a few years back and was advised to change the condenser after a week of doing everything else. Problem solved.
Reply With Quote
  #13   IP: 172.58.184.61
Old 06-09-2018, 09:11 AM
dwkfym dwkfym is offline
Senior Member
 
Join Date: Nov 2017
Posts: 32
Thanks: 0
Thanked 1 Time in 1 Post
Mine was doing that. Turns out that my new tstat housing wasnt tightened enough. Lol
Reply With Quote
  #14   IP: 24.152.132.140
Old 06-09-2018, 09:19 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
If you have a thermostat, not seating it properly in the housing groove can result in leakage too.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Spark plugs. Champion rn12mc4 CalebD General Interest 4 10-08-2015 01:19 PM
sweet fluid seeping up around spark plugs liveaboardL Ignition System 11 03-31-2014 05:06 PM
White smokes+gasoline+black spark plugs Tiree Troubleshooting 25 08-23-2010 12:33 PM
Water bubbling out around spark plugs-need help BobA Troubleshooting 21 10-21-2009 10:54 PM
Ericson 29: Sooty spark plugs learking Troubleshooting 2 03-28-2008 05:23 PM


All times are GMT -4. The time now is 07:13 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved