Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #1   IP: 172.91.172.87
Old 05-13-2020, 06:52 PM
Oday32-CC-LA Oday32-CC-LA is offline
Frequent Contributor
 
Join Date: May 2018
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Paragon reduction gear oil leak - Seal replacement without taking shaft out?

Quick question:

Is there a way to exchange the seal for the Paragon reduction gear without taking the shaft out? Ideally I would like to do it having the boat in the water.

It leaks oil and while not a ton, leaking oil is obviously not ideal.

Thank you all for your help and insights,
Sascha
Reply With Quote
  #2   IP: 32.211.28.40
Old 05-13-2020, 07:21 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,611
Thanks: 9
Thanked 259 Times in 201 Posts
First, try to verify that the leak is coming from the seal and not one of the lower bolts. The lower bolts will leak if they have split lock washers - should have solid washers.
You can unbolt the shaft coupling from the transmission flange, and then slide the shaft and coupling aft until the coupling hits the stuffing box. That might give you room to remove the transmission flange.
First piece forward of that carries the seal. Remove the piece, replace the seal, reinstall. During reinstall, remember that the lower bolts get solid washers, not split.
Reply With Quote
The Following 2 Users Say Thank You to Al Schober For This Useful Post:
Administrator (05-13-2020), lat 64 (05-13-2020)
  #3   IP: 76.7.142.140
Old 05-14-2020, 08:09 AM
Marian Claire's Avatar
Marian Claire Marian Claire is offline
Afourian MVP
 
Join Date: Aug 2007
Posts: 1,754
Thanks: 24
Thanked 96 Times in 70 Posts
+1. I had very little room to move the shaft aft. After marking the location of the engine mounts I unbolted them and moved the A-4 forward enough to remove the reduction gear housing. Not sure if that is an option for you.

Dan
S/V Marian Claire
Reply With Quote
  #4   IP: 172.91.172.87
Old 05-14-2020, 10:17 AM
Oday32-CC-LA Oday32-CC-LA is offline
Frequent Contributor
 
Join Date: May 2018
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Great ideas - super helpful! Thank you!
Reply With Quote
Reply

Tags
oil leak, reduction gear, shaft

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Oil Leak from Paragon Reduction Gear clark800 Troubleshooting 2 07-07-2017 12:49 PM
Shaft removal, cutless, stern tube replacement CalebD Drive Train / Propellers 93 02-07-2014 06:30 PM
Rear shaft oil seal replacement Gari Tartan 18 11-07-2013 02:59 PM
Paragon 2:1 reduction gear lubrication. Mo General Maintenance 18 05-05-2013 03:02 PM


All times are GMT -4. The time now is 12:21 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2020 Moyer Marine Inc.

All Rights Reserved