Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Reversing Gear

Reply
 
Thread Tools Display Modes
  #1   IP: 99.231.137.223
Old 01-21-2019, 05:03 PM
Bratina Bratina is offline
Senior Member
 
Join Date: Jun 2015
Location: Toronto, Ontario
Posts: 96
Thanks: 126
Thanked 26 Times in 17 Posts
RPM in reverse - how much is enough?

Like many posters here, I've been at a point where reverse in my A4-powered Grampian 30 is low to non-existent.

I adjusted the reversing gear (one flat of the nut) towards the end of the season last year and it helped a little, although thrust in reverse remains extremely weak. I'm going to install an Indigo 3-blade prop over the winter, which many forum members have noted is more effective than a 2-blade. It's worth a shot, my boat is on the hard, and the cost is relatively low.

For no rational reason I baby my engine - I cringe when my RPMs climb over 2K, and cruise at between 1600 - 1800 (which nets me around 5kt - plenty for my short stint to get off the dock and out to Lake Ontario). I've read at length people noting that you have to 'really gun it' to get decent thrust backwards, but it's never quantified in terms of actual RPM.

So my question is twofold: what is 'gunning it' in reverse? I usually get to 2-2.2K RPM in reverse and, again irrationally, get scared. Likely part of my problem with the 'brakes'.

Second: a lot of forum members note that it's better for the engine to run at a higher RPM. Should I be scared cruising at 2,000 - 2,200 rpm or higher? Is it true that it's easier on the engine? If temperature and oil pressures are nominal, is it any more risky to run at 2,200 rpm vs. 1,800 rpm? It seems counterintuitive (and I should get a vacuum gauge...).
Reply With Quote
  #2   IP: 173.17.89.29
Old 01-21-2019, 11:21 PM
sailhog sailhog is offline
Senior Member
 
Join Date: Apr 2009
Posts: 289
Thanks: 25
Thanked 13 Times in 9 Posts
Ahoy, Bratina! Others will chime in here, but here's an introductory two cents... The reverse gear on the A-4, I believe, is geared down a third to the forward gear.

Standby for more commentary...
Reply With Quote
  #3   IP: 67.176.202.60
Old 01-22-2019, 10:11 PM
Sam Sam is offline
Afourian MVP
 
Join Date: Apr 2010
Posts: 322
Thanks: 490
Thanked 140 Times in 109 Posts
I'll chime in a bit. Having an older heavy displacement boat, 1966 Morgan 34, with a 3/4 keel somewhat similar to the Grampian you just can not expect make much headway in reverse. The reverse "prop thrust " is hitting the very nearby keel. Reverse "gunning" the throttle stops the boat nicely and the prop walk gets me next to the dock but getting out, especially against the wind is difficult.
Reply With Quote
The Following User Says Thank You to Sam For This Useful Post:
Bratina (01-28-2019)
  #4   IP: 24.152.132.140
Old 01-22-2019, 11:34 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
A technique I learned with my previous full keel boat was to give her a burst of power in reverse to get her moving, then take her out of gear and let her coast. Steering is much more responsive without the prop turning.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Bratina (01-28-2019)
  #5   IP: 192.186.122.174
Old 01-23-2019, 08:40 AM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Quote:
Originally Posted by ndutton View Post
A technique I learned with my previous full keel boat was to give her a burst of power in reverse to get her moving, then take her out of gear and let her coast. Steering is much more responsive without the prop turning.
Exactly what I have to do, and turn to starboard to get facing the right way in the marina channel. brief bursts with the tiller hard to port. The key for my situation is brief busts - say 3-5 sec.... coast... burst....coast...

now, add some wind coming from starboard...
__________________
Greg
1975 Alberg 30

Last edited by GregH; 01-23-2019 at 08:40 AM. Reason: speeling etroshus
Reply With Quote
  #6   IP: 206.125.176.3
Old 01-23-2019, 09:08 AM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
The reversing gear really screams when you rev it up to 2,000+ RPM, and I think until you are used to the noise, it scares people.

Also, newer users to the A4 may not realize they need to lean on the gear lever to hold pressure on the reversing band to keep the prop shaft fully engaged.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
Bratina (01-28-2019)
  #7   IP: 24.152.132.140
Old 01-23-2019, 09:21 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I knew a guy 45 years ago who had a downwind slip in Newport Harbor and no engine, a real handful coming and going. On his way in he would drop a stern hook and use it as a brake, left it there when he was done. Leaving next time he would warp out using the hook and retrieve it when he was clear.

And we complain about prop walk!!
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 2 Users Say Thank You to ndutton For This Useful Post:
Bratina (01-28-2019), sastanley (01-27-2019)
  #8   IP: 32.211.28.40
Old 01-23-2019, 10:13 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
I modified the reverse cam on my transmission to put a flat on it - at full reverse, the roller would come up on the flat and stay there. Personally, I liked the change. No more worry about holding the lever in reverse.
Of course, you have to have your linkage adjusted properly. Forward should just shift things into forward, and reverse was as far as the linkage in the transmission would allow. Side benefit of this was that is gave me a nice wide neutral band. Key is to have a shifter that gives adequate throw.
Reply With Quote
  #9   IP: 179.50.222.56
Old 01-24-2019, 07:49 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Quote:
Originally Posted by ndutton View Post
I knew a guy 45 years ago who had a downwind slip in Newport Harbor and no engine, a real handful coming and going. On his way in he would drop a stern hook and use it as a brake, left it there when he was done. Leaving next time he would warp out using the hook and retrieve it when he was clear.

And we complain about prop walk!!
This fellow could spend months in the summer, trying to get out of the Chesapeake.

Bill
Reply With Quote
  #10   IP: 142.112.13.103
Old 01-28-2019, 10:49 AM
Bratina Bratina is offline
Senior Member
 
Join Date: Jun 2015
Location: Toronto, Ontario
Posts: 96
Thanks: 126
Thanked 26 Times in 17 Posts
Thanks for the replies everyone, super helpful as always.

I'm comfortable with the operation of the engine (e.g. the lack of detente in reverse, the reduction gear etc), and combating prop walk.

What I'm still not too sure of is how much is too much, and whether I risk damaging the engine at a higher RPM.

1. What RPM do you use in reverse (maximum and average)?
2. Is it better for the engine to cruise (forwards) at e.g. 2,200 RPM vs. 1,700 rpm?

I know these things will vary by engine / boat / conditions / prop / hull type etc, but I'm trying to get a feel for how far I can go.
Reply With Quote
  #11   IP: 76.7.141.172
Old 01-28-2019, 11:05 AM
Marian Claire's Avatar
Marian Claire Marian Claire is offline
Afourian MVP
 
Join Date: Aug 2007
Posts: 1,797
Thanks: 33
Thanked 129 Times in 94 Posts
I think following thru with your plan to install a vacuum gauge, as mentioned in post #1, will give you the answer. I believe it is one # that can be compared to other boats despite different set ups.
Dan
S/V Marian Claire
Reply With Quote
The Following 2 Users Say Thank You to Marian Claire For This Useful Post:
Bratina (01-28-2019), thatch (01-28-2019)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
No Reverse pearson1973 Reversing Gear 19 08-18-2017 07:15 AM
Forward and Reverse Gear Adjustment Issues CraigRun Reversing Gear 12 05-17-2012 09:15 PM
Reverse gear overheat?? NorfolkRagbagger Reversing Gear 5 10-13-2010 09:20 AM
Where's Reverse?? ElmaBay Introductions 8 06-02-2009 08:52 PM


All times are GMT -4. The time now is 01:25 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved