Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Overhaul

Reply
 
Thread Tools Display Modes
  #1   IP: 73.100.102.161
Old 04-16-2017, 10:15 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Instead of rebuilding my original A4, I bought a spare one!

Yesterday, I picked up a used A4 from the next town over...Mainly, I did this for several reasons with number being that this A4, from the outside at least, is in much better shape than mine...It was started and ran for a while before I bought it and came with the engine bed.

I am excited to get this as it gives me an opportunity to get it ready easily with paint, FWC, etc.

I first want to check compression on 4 cylinders...If all is good, I plan on just removing the head and side jackets to make sure cooling passages are clean and clear...while at it, I will paint all major pieces separately using the por15 engine paint kit in Pontiac light blue.

Looking forward to it! I still have major work going on my Tartan 34 including removal of all deck hardware, rot removal, etc...so this will probably be done little by little...I plan on providing updates on this project as things get done on this thread.
Attached Images
   
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #2   IP: 24.152.132.65
Old 04-16-2017, 10:25 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Looks like a good score and a fine example of the strategy of choosing one's battles.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #3   IP: 73.100.102.161
Old 04-16-2017, 10:25 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
BTW: I have a small oil leak in the two area below...I assume there are seals that need to be addressed. Input?
Attached Images
  
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #4   IP: 24.152.132.65
Old 04-16-2017, 10:33 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The leak at the flywheel is due to lifting and shipping. There is no seal at that end. The leak from the rear is in fact a rear seal that needs replacement. Easy job out of the boat.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #5   IP: 50.169.162.131
Old 04-16-2017, 11:16 AM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
Southcoasting:

I went through exactly the same process and found it extremely satisfying - I trust you will too. http://www.moyermarine.com/forums/album.php?albumid=150

The por15 black primer is really good - pay attention to the warning about sticking to skin - it won't come off for days if not a week or more.

It looks like the PO paid some attention to the engine - that's a nice find!
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
  #6   IP: 12.189.199.68
Old 04-17-2017, 10:59 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by BunnyPlanet169 View Post
Southcoasting:

I went through exactly the same process and found it extremely satisfying - I trust you will too. http://www.moyermarine.com/forums/album.php?albumid=150

The por15 black primer is really good - pay attention to the warning about sticking to skin - it won't come off for days if not a week or more.

It looks like the PO paid some attention to the engine - that's a nice find!
WOW! looks great! Interesting things you did...Why the 3 hoses going into side plate? Better flow?

The home made electrolysis, can you explain more? Was this used for rust removal or paint removal? How did you remove paint from block?

I was planning on aircraft paint remover...but if you have a better alternative, I'd love to know about it...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #7   IP: 12.189.199.68
Old 04-17-2017, 10:59 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by ndutton View Post
The leak at the flywheel is due to lifting and shipping. There is no seal at that end. The leak from the rear is in fact a rear seal that needs replacement. Easy job out of the boat.
Got it...thank you! Will order new seal soon.
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #8   IP: 76.179.119.203
Old 04-17-2017, 01:35 PM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 94 Times in 67 Posts
Quote:
Originally Posted by southcoasting View Post
WOW! looks great! Interesting things you did...Why the 3 hoses going into side plate? Better flow?
Thanks! Yes, described previously in this thread. http://www.moyermarine.com/forums/showthread.php?t=8979
Have to be honest and say it was a completely irrational PTSD response to a bad cooling experience. The A4 can and will live with less, but I wanted to try and replicate something like the original side jacket casting. I'm not sure I'd do this again.

Quote:
The home made electrolysis, can you explain more? Was this used for rust removal or paint removal? How did you remove paint from block? I was planning on aircraft paint remover...but if you have a better alternative, I'd love to know about it...
Removes rust and (loosens) paint - the bond fails and the paint falls off. Described previously in this thread. http://www.moyermarine.com/forums/showthread.php?t=8526 As I mention in the thread, this is not my original idea, but something common in the old tools / old iron community.

After I found my block had been recently rebuilt (that was a really good day), I took a calculated risk and didn't separate the main castings (rear housing, block, and oil pan). I cleaned them with solvents and wipes, and did some sanding/wire brushing to make the surfaces as friendly as possible for the primer. I used the POR spray acid etch to prevent surface rust and add 'tooth' on bare metal.

It really depends on how far you're planning on / need to disassemble. If I had fully disassembled, I would have taken the big parts to get hot tanked and started from bare metal. My tub was big enough for the flywheel housing and everything else.
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
  #9   IP: 12.189.199.68
Old 04-17-2017, 04:03 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Ran compression test today. Ran engine until warm btw...

3 of the 4 cylinders came back at 100...One came back at 80. Poured a little oil and it jumped to 90.

I assume piston ring is in question?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #10   IP: 73.100.102.161
Old 04-24-2017, 10:00 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Just finished adjusting all valves and poured more mmo into all cylinders to run the engine for a bit again...Mainly trying to see if valve adjustment would fix the cylinder #2 compression to make it match the others...

I bought a vintage set of a Sears/Craftsman Tap & Die set...ordered from ebay. Figured the steel is prob better than new sets made in China today...

I realized the other valve cover bolt was broken when I took the valve cover off and my attempt to extract it created a new hole there that is a bit off center...Should have been more careful...

So I got the new thread in and put it back together and report on the compression...

So after valve adjustment twice and more mmo, I am still getting about 80 psi at most from cylinder 2 and it won't hold the pressure...

My question then is, I suppose something is wrong with the piston rings or at worst, needs cylinder honing.

I think the carb is due for an overhaul...I am learning as I go and have learned a ton from reading on this forum. I went and started her yesterday and let it run for about 15 mins...One thing I noticed was when I open the throttle, it bogs and at one point, it died...I assume this has something to do with carb adjustment...Also ran a little crappy after...

Any suggestions?

I really did not want to do a full rebuild of this engine but seeing what others think when one cylinder is like this...All others are at 100 psi.
Attached Images
  
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #11   IP: 68.111.10.119
Old 04-24-2017, 11:23 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by southcoasting View Post
Just finished adjusting all valves and poured more mmo into all cylinders to run the engine for a bit again...Mainly trying to see if valve adjustment would fix the cylinder #2 compression to make it match the others...
So after valve adjustment twice and more mmo, I am still getting about 80 psi at most from cylinder 2 and it won't hold the pressure...
My question then is, I suppose something is wrong with the piston rings or at worst, needs cylinder honing.
I think the carb is due for an overhaul...I am learning as I go and have learned a ton from reading on this forum. I went and started her yesterday and let it run for about 15 mins...One thing I noticed was when I open the throttle, it bogs and at one point, it died...I assume this has something to do with carb adjustment...Also ran a little crappy after...
.
If you want to do the full on service: (It sounds like you do)
Hopefully it's just a valve hanging up or the seat is pitted or something similar that is causing the low compression. Remove the head and have a look see. While the head is off you can get the cooling jacket and water passages pristine clean. You will be ready to go with FWC then.
The carb main jet is probably blocked. If you rebuild the carb you will know there are no carb problems with the new engine - sort of like starting from zero again.

TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
southcoasting (04-25-2018)
  #12   IP: 73.100.102.161
Old 10-13-2018, 06:48 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
A4 Teardown Begins!

All,
I have finally gotten a chance to start taking apart my replacement spare engine so that I can figure out why one cylinder was around 80 psi and not holding the pressure.

I'd like to avoid going any further than this in the tear down or rebuild since other cylinders came in at 100psi when warm.

Of course, I will be taking off some other parts as I will be stripping paint and repainting but would like to figure out the cylinder number 2 issue as it seems this engine is perfectly fine aside from that...

First thing I noticed was one gasket was used instead of two. Could that be a reason?

What else am I looking for here? I realized I had not removed the gasket from mating surfaces to closely inspect but will be doing so today and posting those pics for your inspection.

As far as valves, what am I looking for to see if they are the culprit?
Attached Images
    
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #13   IP: 73.100.102.161
Old 10-13-2018, 01:47 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
I just poured a couple ounces of mmo on top of cylinder 2 and it slowly drained in about a half hour. Will piston rings let oil go by like that or are the supposed to let some air by?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #14   IP: 137.200.32.54
Old 10-15-2018, 09:53 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Quote:
Originally Posted by southcoasting View Post
I just poured a couple ounces of mmo on top of cylinder 2 and it slowly drained in about a half hour. Will piston rings let oil go by like that or are the supposed to let some air by?
Try putting some in the other 3 and comparing
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
Administrator (10-15-2018)
  #15   IP: 12.189.199.68
Old 10-15-2018, 12:17 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by joe_db View Post
Try putting some in the other 3 and comparing
Thanks Joe.

Well, I decided I am just going to drop this off at the machine shop to have them take a look as I have noticed the pistons are not installed with the arrow pointing correctly anyways...So I'd rather get this right while I have it out and make sure they hot tank, etc...

I will report more info soon.
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #16   IP: 137.200.32.6
Old 10-15-2018, 01:10 PM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Can we assume this block passed a pressure test? If not, put it back together and do one ASAP.
Reply With Quote
  #17   IP: 12.189.199.68
Old 10-16-2018, 07:57 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by joe_db View Post
Can we assume this block passed a pressure test? If not, put it back together and do one ASAP.
I did not...I am pretty far in in the teardown as I just got the tranny taken apart...

Can't the machine shop determine the same thing on their inspection though? Why would I need to do a pressure test unless they can't?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #18   IP: 137.103.82.194
Old 10-16-2018, 11:27 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Quote:
Originally Posted by southcoasting View Post
I did not...I am pretty far in in the teardown as I just got the tranny taken apart...

Can't the machine shop determine the same thing on their inspection though? Why would I need to do a pressure test unless they can't?
Only thing you need for the test is for the head to be on. The machine shop can visually check for cracks and holes, but it isn't exactly the same thing.
Reply With Quote
  #19   IP: 12.189.199.69
Old 12-12-2018, 07:02 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Angry

Just to update everyone, I had dropped off bottom end block for rest of teardown and inspection/measuring. Long story short, my main problem with the compression on one piston was the valve. Also, measurement of piston walls was distorted, most likely due to install of pistons in not the proper orientation. Crankshaft was also a bit screwed so it will need overhaul.

In all, they will be completely rebuilding engine with new bearings, +20 pistons, new rings, new valve springs, crank will be ground down and +.10 or .20 on those as well, they will put the engine back together, hot tanking and paint removal, painting, etc for about $1300 in labor. Parts will be around $1200 as well. In all, not what I expected but a lesson learned...just because an engine looks good on exterior and it had been rebuilt does not mean it was rebuilt correctly.

This rebuilt engine was previously done by a shop/yard who clearly did not know what they were doing and it caused more harm than good. Wish I would have just done this to my original engine and not bought this replacement but oh well...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
The Following User Says Thank You to southcoasting For This Useful Post:
romantic comedy (12-12-2018)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Spare engine- Where to Start? cdhickey Overhaul 1 05-26-2015 02:27 PM
What spare parts to carry. Mo General Interest 6 12-13-2014 03:31 PM
Blasting rusted spare parts ukrsindicat General Interest 2 01-14-2014 12:27 PM
Spare parts for ICW trip tominny General Maintenance 7 08-28-2012 08:30 PM
Keep New impeller as spare, or replace? jimjuliem Cooling System 2 10-26-2007 08:26 PM


All times are GMT -4. The time now is 05:57 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved