Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 67.167.198.24
Old 07-16-2013, 08:40 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
Lightbulb Zero Compression cylinders 3+4

Hello All,

I've been slowly but surely correcting a bunch of problems with my "new to me" A4. It has always ran but very poorly. To date I have done the following to help weed out some potential problems. 1) Electronic Ignition and spark plugs 2) New water pump and thermostat, 3) verified no exhaust blockages and rebuilt the hot-side of the exhaust.

I have always had trouble getting the engine to rev up under load {thus the exhaust work and water side work}

I finally got around to checking compression today after I got the engine warmed up a bit and have the following: #1{nearest flywheel} 100psi, #2 100psi, #3 0psi, #4 -0psi. My guess stuck valves on 3 and 4 so I poured in some MMO and will let it sit overnight. I'm not too thrilled about removing the head and subsequently valves etc if I don't need to. Are there any tests to verify stuck valves are the culprit here and not a gasket? I also have a feeling that running on 2 cylinders for this long has only added to the crud on the valves that are stuck if the spark plugs are any indication as they foul up almost instantly.

Hopefully solving this will get everything running right, it's only been 3 months...
Reply With Quote
  #2   IP: 68.56.139.11
Old 07-16-2013, 09:01 PM
romantic comedy's Avatar
romantic comedy romantic comedy is offline
Afourian MVP
 
Join Date: May 2007
Location: florida
Posts: 1,912
Thanks: 13
Thanked 118 Times in 100 Posts
There is a test called a leak down test. It blow air in the cylinder, and you can see or hear where it leaks out.

You can just shoot compressed air in also.

The easiest? way is to remove the valve cover, and see if the valves are working as you turn the engine over.
Reply With Quote
  #3   IP: 67.68.240.182
Old 07-16-2013, 10:22 PM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
Removing the valve cover and you will see and touch the stuck valves. Here and thru the spark plug holes, you will lower them. Don't force them too much.
Reply With Quote
  #4   IP: 50.29.99.167
Old 07-17-2013, 09:04 AM
Skywalker's Avatar
Skywalker Skywalker is offline
 
Join Date: Jan 2012
Location: Stony Brook, NY
Posts: 621
Thanks: 0
Thanked 17 Times in 12 Posts
I had the same problem earlier this season. Pull off the side plate and have a look. I had to give one a couple of taps and it snapped free. Been fine ever since.

Chris
Reply With Quote
  #5   IP: 50.79.118.57
Old 07-17-2013, 03:27 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
Side Plate

Can I get at the side plate without removing the manifold? Carb? I have good access to the engine as tartan 27's have the engine under the removable companionway steps. Will I need a new gasket for the valve cover? I don't want to cause more trouble. New gaskets are on the way but if I can do this today all the better.
Reply With Quote
  #6   IP: 50.29.93.208
Old 07-17-2013, 05:07 PM
Skywalker's Avatar
Skywalker Skywalker is offline
 
Join Date: Jan 2012
Location: Stony Brook, NY
Posts: 621
Thanks: 0
Thanked 17 Times in 12 Posts
Yes, easy access without removing manifold. Pull the carb off. I'd use a new gasket.

Chris
Reply With Quote
  #7   IP: 71.178.85.239
Old 07-17-2013, 11:01 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
T27, it is late now, but the data you got from Chris is good. The valve cover gasket is cork if I remember. It is hit or miss if they come off in one piece. The carb gasket is paper, and as Chris said, I'd use a new one if I had it.

There is not a lot of activity on the valve cover side, so you might be OK with some permatex to re-seal the cork.

My personal plan of attack since I've owned my boat is to have one of EVERY gasket the engine needs on board the boat as a spare. The ones you would expect to use up frequently (carb, t-stat, maybe water pump) I'd have 3 or 4 on hand, but at least one of everything, including head gasket, valve cover, water jacket side plate, etc....oil pan gaskets are show stoppers since you would need to pull the engine on most boats, but I do have a coupling gasket & manifold gasket aboard. The gaskets are cheap, so you might as well bulk ship them in one order...some you may never use, but you have the ones you may use frequently. I have a shoe box size plastic container with a snap lid with all my engine spare parts in it...works great.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 07-17-2013 at 11:09 PM.
Reply With Quote
  #8   IP: 128.183.140.38
Old 07-18-2013, 10:40 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
You can fit all your spares in a shoebox???
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #9   IP: 71.178.85.239
Old 07-18-2013, 10:43 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
ed, almost.

That does not include spare coil, fuel pump, carb, etc. They are in a separate box.

All of my gaskets, o-rings, fuel filters, and Permatex fit in there though.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #10   IP: 67.167.198.24
Old 07-25-2013, 10:01 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
Smile So there's yer problem...

Finally got back out to the boat after a week away visiting family. I removed the head in 30 minutes flat; no stuck nuts, it was almost too easy. Gasket was fine, no leaks between cylinders. Once open I found the exhaust valves on 3 and 4 stuck open. I rotated the engine so both of these should be closed and progressively tapped the stuck valves harder and harder until then begrudgingly {much harder than I expected, thanks to a light hammer and dowel} went back down to their seats. Rotated the engine a bit more and they opened back up and stayed there, more tapping {still hard, but a bit less} and they scooted down. I tried rotating them while up next and it took quite a bit of trying to twist at all.

How do I get them completely free? I would like to avoid removing the springs if at all possible so I left some MMO along the valves to hopefully work some magic overnight. What else can be done, I want everything moving smoothly before I put the head back on.
Reply With Quote
  #11   IP: 71.178.85.239
Old 07-25-2013, 10:17 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Thumbs up progress is good!

T27.. I had a sticky #4 exhaust valve. Not 100% stuck, but #4 was much weaker than the others and had 25PSI or so less of pressure, so, I squirted MMO in the cylinders after every use for almost a whole season..it got progressively better.

I am not sure exactly what the real solution is, but continued massaging may help...but I think running it is likely best now that you've got them 'un-stuck'. Dave Neptune likes to run some good 2-stroke oil in his gas to help lube the valve guides....the real issue here is these are exhaust so the oil won't help too much since we expect it got burned on the compression stroke..however, it can't hurt. I'd also be liberal with the MMO (I did 4 or 5 squirts with an oil can) after every run for a while and see if it helps.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #12   IP: 67.167.198.24
Old 07-25-2013, 10:45 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
Post removing the valves

From reading others' posts it appears that the "keepers" are keeping the valves down in the guides, this is the friction I'm feeling when trying to twist no doubt. Can I remove these without releasing the spring? i REALLY do not want to have to by new tools to re-install a spring. How are the keepers removed so I can pull the valve, sand off any rust and reinstall?
Reply With Quote
  #13   IP: 71.178.85.239
Old 07-25-2013, 11:50 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
T27...I think the answer to your question is no...

Even though I have not had to use it (yet), the PO left a valve spring tool on the boat. I am pretty sure he got it from Moyer, but he beefed it up just a little bit with a cross brace. It compresses the spring, so you can pull the keepers and get the valve out. He reported frozen valves in the past from water intrusion (overcranking) events, and he had to clean the rust off the valve stems and ream the guides out using a reaming tool (also on the boat), which I assume came from Moyer too..I think they've bumped the original diameter from .314" to .316", perhaps to help with this exact problem, but those numbers are from memory, and need to be verified with an authoritative source like Ken in the Moyer parts dept.

Be careful not to drop the keepers into the oil drain holes in the bottom of the valve chamber...lots of people lay a rag into the bottom to keep stuff from falling into the oil pan. There are some other notes related to the keepers here on the forum that are likely helpful..I guess sometimes they are hard to re-install since they are small and us humans have big fingers...a search would probably help you out there.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 07-25-2013 at 11:56 PM.
Reply With Quote
  #14   IP: 68.56.139.11
Old 07-25-2013, 11:50 PM
romantic comedy's Avatar
romantic comedy romantic comedy is offline
Afourian MVP
 
Join Date: May 2007
Location: florida
Posts: 1,912
Thanks: 13
Thanked 118 Times in 100 Posts
Keepers are the little pieces that stop the spring from going off the end of the valve. The valve has grooves in the end of the shaft. The spring goes on the valve, then the retainer, then the keepers. The retainer is like a washer that covers the spring. The keepers go around the stem, to hole the retainer on the stem.

The valve slide in the guide, that is pressed into the engine. Build up of material causes friction between the valve stem and the guide. This is what holds the valve open.

Guys use different solvents to dissolve the buildup. If the valve was bent, it would stick also. Since you have the head off, removing the valve is not that hard. This would be the best way to clean the guide, and assure that the valve worked.
Reply With Quote
  #15   IP: 75.236.107.255
Old 07-26-2013, 12:36 AM
Carl-T705 Carl-T705 is offline
 
Join Date: Jul 2011
Location: Georgia
Posts: 251
Thanks: 0
Thanked 0 Times in 0 Posts
Don't think that if the valves been stuck that they will just pop free and go to working that quick. you'll have to fool with them for quite a while if you want them to free up without removing them . It can be done , I've done it , it just takes time and continued working of them up and down with liberal doses of oil, you may want try using gun cleaning oil. They will free up, unless in your forcing to free them up you bent the valve stem.I'm glad to hear you removed the head to see what your working with. It's best to see what you're actually forcing to move It's a pretty easy task that will get you more comfortable with working around this great little engine. Some think it's mandatory to remove the head studs, but if they are not loose or damaged I leave them intact, don't create more problems that are more difficult to repair. Valve stem clearances are measured in the thousandths, keep that in mind if you have to remove and sand down for clearance,
Reply With Quote
  #16   IP: 24.196.40.186
Old 07-26-2013, 08:11 AM
Laker Laker is offline
Senior Member
 
Join Date: Sep 2010
Location: Sheboygan wis.
Posts: 454
Thanks: 2
Thanked 3 Times in 3 Posts
Sanding ?!?

Sanding valve stems scares me. I had the same problem as you , albeit one cylinder. With the head off I applied various lubricants to the valve stem , including carb cleaner , and gently rotated the valve. It took several tries , and a couple more head removals , but the offending valve has now been trouble free for 3 years.

Stick with it. (pardon the pun.) CK
__________________
1966 Columbia 34 SABINA
Reply With Quote
  #17   IP: 65.95.35.117
Old 07-26-2013, 08:23 AM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
T27, you can have a higher success rate stripping the carbon of the valve stem in the valve guide, by using ''Brake Cleaner" in aerosol. Put that little tube under the valve and blast away. Its fast acting, then evaporates. Finishing the job with MMO overnight. Warming up the valve before, can help.
While you are there do the other vales somewhat.
Reply With Quote
  #18   IP: 71.118.13.238
Old 07-26-2013, 12:35 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Thumbs up Work 'em loose

T27, you can use the starter to rotate the engine a spray a bit of penetrating oil on the stems. As the engine is rotating you can use "finger" pressure on the valves to assist them to work loose. It won't hurt the starter as there is virtually no load on it! Once they cycle fine it's time for the getting running part.

I would recommend a mix of "2-stroke (my preference) oil", or MMO in the fuel at around 100:1 mix. It may smoke a tiny bit but the oil will get to the stems as it's running and continue flushing whatever was broke loose in the guides. I'd run it thusly for about 10 gallons then go back to straight regular grade gas.

Dave Neptune
Reply With Quote
  #19   IP: 71.118.13.238
Old 07-26-2013, 12:38 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Red face 1 mo' ting

Using the brake cleaner or carb cleaner will really help getting the sludge off the stems. Once done with those go to the penetrating oil to lubricate and flush. The "cleaners" will leave the guides and stems clean and dry and just as ripe as they could be to gather rust.

Dave Neptune
Reply With Quote
  #20   IP: 67.167.198.24
Old 07-27-2013, 10:40 AM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
Cool Its alive!!!!!

I just wanted to throw out a bit THANK YOU to everyone on this forum. After 4 hours of turning the engine by hand and tapping down valves while squirting a whole can of brake cleaner I got everything running smoothly. I didn't know that the atom bomb was supposed to run so smoothly and so quiet.

Here's what I can put together:

1)valves got stuck quite some time ago and the previous owner couldn't figure it out. This caused the motor to start sucking water in through the exhaust valves only making the problem worse.

2)previous owner turned the water pump WAY down to compensate and ruined the pump.

3) That still didn't solve the problem so they cut the exhaust in half so it could breathe which kinda worked and since they were on a bouy it didn't matter that the engine ran like crap.

4) I got it and started treating the water side issues assuming that the broken exhaust and pump were causing the crappy running. They were but indirectly.

5) two VERY stuck valves {took a hammer and dowel to free them and 4 hours of cleaning) later the engine runs like new.

I've now got a electronic ignition, new pump, new exhaust, rebuilt carb and last but not least a functioning set of valves. Many thanks again to everyone for the support and advice. Hopefully this atom bomb will keep on ticking and I can put away the thoughts of converting to electric.
Reply With Quote
The Following User Says Thank You to T27_478 For This Useful Post:
DDO (03-30-2021)
  #21   IP: 66.108.51.167
Old 07-27-2013, 01:53 PM
CalebD's Avatar
CalebD CalebD is offline
Afourian MVP
 
Join Date: May 2007
Location: NYC
Posts: 899
Thanks: 18
Thanked 22 Times in 20 Posts
Good for you T27_478!!!

A well running A4 is a quiet thing of beauty. Some diesel owner's question whether our engines are even running as they run so quietly.

You did a great job debugging your engine. The guys here helped with suggestions but you did the work. Congrats!

Have you already joined our Tartan 27 owners group on Yahoo? It is called T27Owners.
__________________
Tartan 27 #328 owner born 1958
A4 and boat are from 1967
Reply With Quote
  #22   IP: 68.56.139.11
Old 07-27-2013, 09:33 PM
romantic comedy's Avatar
romantic comedy romantic comedy is offline
Afourian MVP
 
Join Date: May 2007
Location: florida
Posts: 1,912
Thanks: 13
Thanked 118 Times in 100 Posts
Question T27...

you say....

2)previous owner turned the water pump WAY down to compensate and ruined the pump.

3) That still didn't solve the problem so they cut the exhaust in half so it could breathe which kinda worked and since they were on a bouy it didn't matter that the engine ran like crap.


What do you mean, that they cut exhaust in half?

Also, how did they turn down the water pump?
Reply With Quote
  #23   IP: 184.74.5.83
Old 07-27-2013, 10:45 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
I wondered the same things.

Maybe they didn't open the raw water intake all the way?

No idea how one would "cut the exhaust in half".
Reply With Quote
  #24   IP: 67.167.198.24
Old 07-30-2013, 02:18 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
You are correct, they turned the raw water intake nearly off and that in-turn wore out the pump. Not only was the impeller shot but the shear pin on the impeller sheared off.

as far as cut the exhaust in half a picture is worth a thousand words. The above photo was taken after I removed some exhaust patch materials that were nearly rusted through. I replaced the whole thing with galvanized {not a vote one way or the other on the black-iron vs galvanized debate, they only had the right size in the galvanized}

Last edited by T27_478; 07-30-2013 at 02:20 PM. Reason: photo didnt attach
Reply With Quote
  #25   IP: 67.167.198.24
Old 07-30-2013, 02:22 PM
T27_478 T27_478 is offline
Senior Member
 
Join Date: Jun 2013
Posts: 30
Thanks: 0
Thanked 1 Time in 1 Post
tartan27 owners

Caleb,

I have found the owners site and have gleaned quite a bit of info thanks.
Reply With Quote
Reply

Tags
0 compression, fouled plugs, head gasket, stuck valves, zero compression

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Low Compression on middle two cylinders GMcK106 Troubleshooting 23 07-19-2013 08:50 AM
Another Low Compression Issue Triton106 Troubleshooting 19 09-19-2011 09:27 AM
Compression after replacing head gasket jpian0923 Overhaul 5 03-04-2011 01:33 AM
Water in cylinders and no compression gregt Troubleshooting 4 07-26-2010 12:21 PM
Lower compression in non-adjacent cylinders rods a4 Troubleshooting 4 08-24-2007 02:40 PM


All times are GMT -4. The time now is 03:00 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved