Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Ignition System

Reply
 
Thread Tools Display Modes
  #1   IP: 76.66.159.112
Old 10-08-2018, 02:54 PM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Distributor Adjusting

I have done searches and even tried to find this simple answer in The Manual - what do I loosen to be able to rotate the distributor for timing tuning?? I cannot find this simple answer

Thanks for your help in even these small questions.

Last edited by GregH; 10-09-2018 at 08:44 AM.
Reply With Quote
  #2   IP: 162.22.248.100
Old 10-08-2018, 03:35 PM
rickinnj's Avatar
rickinnj rickinnj is offline
Senior Member
 
Join Date: Dec 2010
Location: South Joysee
Posts: 103
Thanks: 3
Thanked 4 Times in 4 Posts
There's a bolt and hold-down clamp at the base of the distributor on the reversing gear side. I believe it's a 9/16". If you pull up the 360 view of the engine on the home page and spin it around to the reversing gear end of the motor, you'll see it at the base of the distributor.

Hope that helps
__________________
Rick Bushie
s/v Anchovy, 1971 C&C 30-1, Hull #1
Tolchester, MD
Reply With Quote
  #3   IP: 184.176.196.206
Old 10-08-2018, 04:36 PM
CajunSpike's Avatar
CajunSpike CajunSpike is offline
Senior Member
 
Join Date: Jan 2018
Location: New Orleans, LA
Posts: 240
Thanks: 222
Thanked 41 Times in 31 Posts
Isn't the distributor for TIMING tuning and not rpm tuning?
__________________
Bill L.
1972 Ericson 27
Hull #61
Atomic 4
Reply With Quote
  #4   IP: 73.178.188.222
Old 10-08-2018, 07:17 PM
rickinnj's Avatar
rickinnj rickinnj is offline
Senior Member
 
Join Date: Dec 2010
Location: South Joysee
Posts: 103
Thanks: 3
Thanked 4 Times in 4 Posts
Yes...but I believe the Moyer Manual tells us to adjust timing to achieve best loaded rpm...or something like that.
__________________
Rick Bushie
s/v Anchovy, 1971 C&C 30-1, Hull #1
Tolchester, MD
Reply With Quote
  #5   IP: 192.186.122.174
Old 10-09-2018, 08:44 AM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Quote:
Originally Posted by CajunSpike View Post
Isn't the distributor for TIMING tuning and not rpm tuning?

Yes you are correct - my bad.. edited
Reply With Quote
  #6   IP: 192.186.122.174
Old 10-09-2018, 08:47 AM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Quote:
Originally Posted by rickinnj View Post
There's a bolt and hold-down clamp at the base of the distributor on the reversing gear side. I believe it's a 9/16". If you pull up the 360 view of the engine on the home page and spin it around to the reversing gear end of the motor, you'll see it at the base of the distributor.

Hope that helps
hmm.. ok I DID do the right thing.. loosened it enough that I could move the bolt with bare fingers (which I realize is too much), but could not get the dist to budge. Didn't want to try too hard as never done this part before and worried about "doing something" shouldn't.

suggestions?

- once loosened give the clamp a tap with the wrench?
- little MMO to loosen things up?

Last edited by GregH; 10-09-2018 at 08:51 AM.
Reply With Quote
  #7   IP: 24.152.132.140
Old 10-09-2018, 09:34 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Using max loaded RPM as a timing indicator requires the advance weights to be in good, free moving and lubricated condition for a proper result.

Is there an aversion to setting timing to the marks with a timing light? That's what I did and my engine runs the best it ever has. If the factory marks are difficult to access or see, create your own (also what I did).

http://www.moyermarineforum.com/foru...d.php?p=108158
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #8   IP: 99.30.185.198
Old 10-09-2018, 10:37 AM
thatch thatch is online now
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
"Ditto"

I could have just given Neil a "Thumbs up" stamp on his recommendation to read the previous thread about "timing light timing", but the difference in the way an A4 will start and run is such an improvement that I feel it is worth elaborating on. Proper timing and having a good fitting slash tube can eliminate the need for an aftermarket PCV valve.
Tom
Reply With Quote
  #9   IP: 192.186.122.174
Old 10-09-2018, 11:52 AM
GregH's Avatar
GregH GregH is offline
Afourian MVP
 
Join Date: Jun 2015
Location: Kingston, ON
Posts: 564
Thanks: 385
Thanked 103 Times in 80 Posts
Quote:
Originally Posted by ndutton View Post
Using max loaded RPM as a timing indicator requires the advance weights to be in good, free moving and lubricated condition for a proper result.

Is there an aversion to setting timing to the marks with a timing light? That's what I did and my engine runs the best it ever has. If the factory marks are difficult to access or see, create your own (also what I did).

http://www.moyermarineforum.com/foru...d.php?p=108158
Before starting things yesterday I made a mark on the flywheel pin (when #1 at TDC) and at current idle of ~900 rpm the timing light was showing the tick mark to be to the right of the mark on the flywheel cover (sorry no pics). This is when I went to loosen the dist clamp and could not get it to move - so I thought I was doing it wrong and thought best to check here.

Should I be able to take that clamp right off to make sure it isn't rusted/stuck without worrying about the dist moving? Then once know that attach it back on snug but enough so dist can rotate?

How much effort does it take to rotate?
Reply With Quote
  #10   IP: 99.30.185.198
Old 10-09-2018, 12:30 PM
thatch thatch is online now
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Greg, It is not unusual for the distributor to be a little frozen in place. There is (or should be) a gasket between it and the block that needs to be freed up. I'd spray WD-40 on that area and then try tapping on the base of the dizzy with a drift. Once it is freed up, it will rotate very easily. During the actual timing process "snug" the hold down bolt enough so that you can still rotate it but don't have it loose enough the engine will rotate it. If you are using a timing light, it is important that the advance weights are fully retarded. Reducing the idle as much as possible should insure this. If your carb is clean and you do not have a PCV valve, an idle of about 700 rpm is normally attainable. I have found that I can adjust any of my carb's idle mixture screws to about 1-3/8 turns out and have a good "out of the box" idle. Hope this helps.
Tom
Reply With Quote
  #11   IP: 24.152.132.140
Old 10-09-2018, 04:46 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by GregH View Post
Before starting things yesterday I made a mark on the flywheel pin (when #1 at TDC) and at current idle of ~900 rpm the timing light was showing the tick mark to be to the right of the mark on the flywheel cover
If you see the same timing mark misalignment after reducing the idle RPM, this is the typical power timing error - a little on the advanced side.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
GregH (10-10-2018)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:36 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved