Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 174.200.2.112
Old 09-02-2018, 03:35 PM
Runner37 Runner37 is offline
New Member
 
Join Date: Jun 2016
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Help, engine does not start

I installed a brand new Moyer marine atomic4 in my allied luders finishing last August. It ran great. This spring it acted like it wasn't getting enough voltage when I started it so I replaced the batteries. It started but acted like there was still low voltage the next time I started it. I left it for two weeks and came back. It cranked once then nothing. Batteries are fully charged. I have checked all of the wiring, cleaned all of the battery posts, installed a new solenoid, hot wired the solenoid and don't even get a click. Is it the starter? Seems unlikely. I hand cranked the engine with the plugs out, it turns just fine.

I have12.7 volts at the big post from the battteries to the batt post from the battery switch and ignition. From the st switch on the ignition to the s post on the solenoid I get 12.7 volts with the ignition turned on. I have checked the continuity of all the grounds. The ground from the solenoid is to a buss bar which is grounded to the rear of the block. I jumped it and checked it and it's good.

I'm stumped. Help! I'd rather sail than work on my engine.
Reply With Quote
  #2   IP: 24.152.132.140
Old 09-03-2018, 09:26 AM
ndutton's Avatar
ndutton ndutton is online now
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 8,240
Thanks: 127
Thanked 1,072 Times in 721 Posts
Please take a few more voltage tests for which you will need a helper.
  1. Two tests from the large solenoid post to two different grounds while the helper is pushing the start button/keyswitch in the cockpit. The two grounds are the engine block and the battery - post.
  2. Same two tests except between the solenoid output strap to the starter and the two grounds.
What I'm suspecting here is a cable or solenoid issue. With such a problem you'll read voltage at rest but it will drop significantly under load (during starting). The reason for the different grounds is to home in on which cable. I admit it's a guess but one I'd like to see confirmed or eliminated.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 09-03-2018 at 09:59 AM.
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Administrator (09-03-2018)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
engine won't start sailr Troubleshooting 34 10-09-2018 01:25 PM
Engine won't start, 3 cylinders no compression Brent W Troubleshooting 27 07-15-2017 01:33 PM
Sudden very ragged running problem pdecker Troubleshooting 28 09-08-2015 08:46 PM
Engine very hard to start after cleaning distributor advance mechanism TomG Troubleshooting 10 02-11-2012 05:56 PM
Engine won't start, but I'm narrowing it down. Keir Hood Troubleshooting 3 06-23-2006 09:04 AM


All times are GMT -4. The time now is 11:49 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2018 Moyer Marine Inc.

All Rights Reserved