#1
IP: 156.34.176.57
|
|||
|
|||
Tachometer install
My Grampian 28 does not have factory installed tachometer - only oil pressure, temperature and ammeter gauges. Some owner before me installed an electronic gauge like on the picture but I don't think it's accurate. The minimum RPM it shows is 2800 when idle. Sometime it shows 5000 - 6000 when pull throttle to push the boat a little bit forward or reverse. All in all, it seems to be not working properly.
A couple questions I have. Which RPM gauge is recommended? How to wire it into the engine? |
#2
IP: 24.152.132.140
|
||||
|
||||
Have you gone through the select button functions to be sure it is on 4 cylinders?
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
The Following User Says Thank You to ndutton For This Useful Post: | ||
amizerin (09-20-2019) |
#3
IP: 156.34.176.57
|
|||
|
|||
I did not play with the button but probably you're right. There might be a switch between 2 and 4 cylinders.
|
#4
IP: 108.34.253.10
|
|||
|
|||
A review of an hour/tach that resembles yours notes the following:
"They always work on one cylinder engines. With multi-cylinder engines they often pick up signals from more than one cylinder." This might explain why your lowest RPM is 2800 (actually 700?). |
The Following User Says Thank You to jcwright For This Useful Post: | ||
amizerin (09-20-2019) |
#5
IP: 156.34.176.57
|
|||
|
|||
That sounds like exactly what's happening Well... I'm not sure I like to do the math dividing by 4 every time I check RPM. Is there a solution for that? A gauge that works with 4 cylinders?
|
#6
IP: 24.152.132.140
|
||||
|
||||
MMI catalog?
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#7
IP: 156.34.176.57
|
|||
|
|||
How to I connect the RPM gauge to the engine?
|
#8
IP: 24.152.132.140
|
||||
|
||||
It depends on the gauge. The typical gas engine tachometer such as you'll find with Moyer gets 12VDC + and - plus a wire to the '-' terminal on the coil.
Another style of gauge (diesel style, I have one) gets 12VDC + and - plus a signal from the alternator. Unless your alternator already has an AC tap for this purpose I would avoid this type of tach. It also requires calibration because of different pulley ratios on different engines. In other words, much more hassle.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others Last edited by ndutton; 09-20-2019 at 11:52 AM. |
#9
IP: 156.34.176.57
|
|||
|
|||
Quote:
|
#10
IP: 73.239.55.5
|
|||
|
|||
I'd like to add a 2" tach to my A4. But I have no sensor or previous install to wire to.
If I read the above correctly, it just simply wires to the coil and counts pulses? No other sensor is required? I've tried some of those electronic ones and agree they are junk... TIA, Jack |
#11
IP: 32.211.28.40
|
||||
|
||||
I don't think you need tach installed full time - just when you're doing diagnostics.
My meter is an antique Heathkit dwell/tachometer - probably 50 or 60 years old. Analog meter. It clips to the coil, so you have to set it for the number of cylinders. If it died, I'd look on Amazon - dwell tachometer - and see what's offered. My eyesight being what it is, I'd probably look for a big analog meter. Don't need digital. |
#12
IP: 199.231.247.243
|
|||
|
|||
No, I sometimes hear a miss or something while underway, maybe water in my fuel or something. I like to be able to check and also calibrate my boat speed to tach.
Jack |
#13
IP: 100.36.65.17
|
||||
|
||||
Quote:
Most Gas engine tachs have some sort of switch or jumpers to set the number of cylinders (1, 2, 4, 6, 8). Occasionally, this switch will be labeled in "pulses per revolution" instead of "cylinders". For the A4 (or any 4 cylinder 4-cycle engine), this should be set to "2" (1 pulse per cyl every 2 revs x 4 cyls = 2 pulses per rev)
__________________
@(^.^)@ Ed 1977 Pearson P-323 "Dolce Vita" with rebuilt Atomic-4 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Marine tach? | Ajax | Electrical | 11 | 09-24-2015 12:47 PM |
Original Tachometer Wiring? | sailingchance | Electrical | 11 | 05-13-2014 12:06 AM |
Pearson 35 Upgrading to 2 to 1 reduction | jeffgerritsen | Pearson | 41 | 02-24-2011 02:29 PM |
Odd lamp behavior in tachometer | kwalters | Electrical | 1 | 07-12-2010 12:11 PM |
Tachometer Problem | msl3v | Troubleshooting | 1 | 12-31-2009 04:35 PM |