Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Exhaust System

Reply
 
Thread Tools Display Modes
  #1   IP: 76.126.110.141
Old 07-08-2019, 11:22 PM
Chris Simenstad's Avatar
Chris Simenstad Chris Simenstad is offline
Senior Member
 
Join Date: Oct 2007
Posts: 52
Thanks: 0
Thanked 10 Times in 2 Posts
Water out of manifold bolt holes?

The six-year-old hot exhaust section on my A-4 corroded out. It was black iron. The engine is raw (salt) water cooled, and I put about 100 hours on the engine every year. Every time I put the boat away I flush the raw water out of the engine with fresh water.

As I removed the exhaust section, water trickled out of the two manifold bolt holes that mount the flange. The dry exhaust part of the manifold was dry, however.

Is this normal, or is the water cooled part of the manifold corroding, allowing water to seep to the bolt holes? The manifold is about 10 years old. Before I started working on the engine a mechanic replaced the original manifold with an aftermarket one.

Thanks,
Chris
Reply With Quote
  #2   IP: 32.211.28.40
Old 07-09-2019, 09:41 AM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,472
Thanks: 9
Thanked 186 Times in 161 Posts
On the original manifolds, I think those holes were blind (ie: didn't go through into the water jacket). Aftermarket manifolds may be tapped through. Big issue as I see it is exposure of the fasteners to water and the resulting corrosion.
Recommend you change the fastening configuration for your exhaust flange to studs and nuts. I'd make stainless studs out of set screws or all-thread and bond them into the manifold with JB Weld. Then use nuts to hold the flange to the manifold.
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
thatch (07-09-2019)
  #3   IP: 107.77.75.50
Old 07-09-2019, 02:50 PM
Chris Simenstad's Avatar
Chris Simenstad Chris Simenstad is offline
Senior Member
 
Join Date: Oct 2007
Posts: 52
Thanks: 0
Thanked 10 Times in 2 Posts
Thanks for the reply and recommendations.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Should these water holes be blocked? CamaroMan Cooling System 6 06-03-2018 02:13 AM
Intake/Exhaust Manifold Irwin30 General Interest 2 08-16-2010 08:50 AM
water from manifold stud hole? hank Exhaust System 17 09-24-2009 05:01 PM
Exhaust Manifold Aft Water Exit jtownsend003@aol.com Cooling System 1 10-28-2008 08:14 PM
re-plumbing for hot water heater operation Jesse Delanoy Cooling System 10 04-21-2008 08:05 PM


All times are GMT -4. The time now is 12:31 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2019 Moyer Marine Inc.

All Rights Reserved