Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 172.249.104.171
Old 02-04-2020, 08:47 PM
CamaroMan CamaroMan is offline
 
Join Date: Oct 2017
Location: San Pedro, CA
Posts: 42
Thanks: 3
Thanked 10 Times in 5 Posts
blowby issue when under load - smokey!

Hi all - have a a4.. just replaced the head gasket (it blew) - was an old asbestos one.. head wasnt warped.. just did a nice block sand and its holding well.

Now when under throttle, after a while there is quite a bit of smoke coming from the filler cap making it quite unpleasant below.

The card was rebuilt, the vent hose is in good shape.. seems either the valve guides are real bad (oil being pulled in when hot) and a certain amount of blowby-

Usually blowby is mostly air, but the smoke seems to indicate oil. Fyi new oil 5 hours ago and still very clean.

Any ideas? iirc weight was a 10w30-

Is there an option to put a cap on with a hose to the air intake or maybe block it off and force the vapors thru the carb via the intake?
Reply With Quote
  #2   IP: 155.186.124.219
Old 02-05-2020, 10:12 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
CamaroMan, Indigo makes a PCV kit for just what you are talking about. Frankly I would not run an A-4 without one!!! These engines were designed before the PCV valve was invented. The designers did engineer a slash tube to try for the same thing, the valve just works better and is far more efficient at reducing blowby fumes from the engine.

Do you use your blower full time or just to start. Gasoline engines should have a full time blower no exceptions for safety! IMHO

The other cause/remedy is to much lead in the timing. IE your timing needs to be set and probably is to advanced. Try backing the timing up a bit ab=nd be sure the c-advance is functioning.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
Sam (02-05-2020)
  #3   IP: 172.249.104.171
Old 02-05-2020, 10:52 AM
CamaroMan CamaroMan is offline
 
Join Date: Oct 2017
Location: San Pedro, CA
Posts: 42
Thanks: 3
Thanked 10 Times in 5 Posts
thanks dave - will try the timing and look into the pcv kit! I kinda did set the timing by ear - motor warmed well, in gear at dock and around 2500-3k rpms.. rotate to when rpms just start to increase near max under load- I have no access to the flywheel.. starts and ticks over quite easy-


fyi how would timing cause blow by? pushing back past rings while piston still moving up?

Guess ill have to go and remove #1 plug, use a straw, find the center of the dwell and paint on a dab on water pump body and pulley
Reply With Quote
  #4   IP: 155.186.124.219
Old 02-05-2020, 11:49 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
CaamaroMan, it is the "timing" of the fuel burn that makes pressure against the piston creating your power. If the burn starts to soon the pressure increases faster than the piston can react causing an excessive load on the rings to seal and thus "blowing" by a bit. When the burn is right the cylinder pressure is more constant and the "leverage angles" of the rod against the crank increase as the cylinder pressure increases creating a happy "torque" making engine.

The A-4 has very low compression and requires a very low pressure fuel to make smooth reliable power. Regular grade gas of today is designed for far higher compression. For this reason using Premium grades is a waste and if we could find a lower octane fuel it would work better in the A-4. The fuels of long ago would barely run in todays engines.

Setting the timing by ear is fine if you are careful. Do it at a good hard cruising speed on the water if possible or even against the dock lines. Be sure she is all warmed up and the distributor is loose enough to rotate but stay in place when released. Slowly rotate until a max RPM is reached then "retard the timing just a tiny bit which will smooth it out and loose very few RPM. This will make a good smooth running engine.

Dave Neptune

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
GregH (02-05-2020), Sam (02-05-2020)
  #5   IP: 70.185.132.167
Old 02-05-2020, 07:38 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
How long has it been since you serviced the advance?
If the flyweights are sticking or moving with friction the timing will never be correct.


ex TRUE GRIT
Reply With Quote
  #6   IP: 32.211.28.40
Old 02-05-2020, 08:11 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
Based on your replacing a copper/asbestos head gasket, it's been a LONG time since someone's been into that engine (perhaps never). IMHO, it's very likely that it needs rings. Good news is that's likely ALL it needs. I'd recommend you plan on pulling the engine (at your convenience, good therapeutic winter job) and going through it.
Bearings may be fine - do some diagnostics on your oil pressure. How is your oil pressure currently? What pressures do you get if you tighten/loosen the oil pressure adjustment?
Dave's tuning suggestions may reduce the blowby to the point where you can live with it until you do the rings. Running the blower (sucker?) will certainly help.
Engine in the shop/basement is a good time to clean it out and convert to glycol cooling (heat exchanger) if you don't already have it.
Reply With Quote
  #7   IP: 172.249.104.171
Old 02-05-2020, 10:00 PM
CamaroMan CamaroMan is offline
 
Join Date: Oct 2017
Location: San Pedro, CA
Posts: 42
Thanks: 3
Thanked 10 Times in 5 Posts
hi chaps - thanks once again. I did check the distributor springs, they were loose and snapped back-

I wet down there today and she wouldnt start!! I have almost no access to the flywheel for a tdc mark so i rotated till t#1 was on comp and just stopped blowing- used a screw driver and rotated backwards and got a good snap of a spark..

still really struggled - i suspect the new oil switch is perhaps not functioning (AC delco) - the pump did not seem to prime unless i jumped the wires, possibly indicating a low oil pressure situation (dip stick reads 2/3rds to full mark).

just went thru everything basically - only thing is the coil primary resistance is perhaps a little low at 2 ohms - so once with 3 is on the way 2moro but a lower pri resistance coil should deliver a hotter spark -

either way going back in the morning early before work to see what I can do.

Thanks for the input! i did do a comp test when gasket was blown and she was around 55-60 on all and all four were pushing bubbles out between block and head-

fyi is the idle mixture rich or lean when turning out? i suspect lean?
Reply With Quote
  #8   IP: 155.186.124.219
Old 02-05-2020, 10:57 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
The idle mix adjustment is air control so out is lean & in is rich.

Dave Neptune
Reply With Quote
  #9   IP: 76.80.111.174
Old 02-06-2020, 03:47 PM
CamaroMan CamaroMan is offline
 
Join Date: Oct 2017
Location: San Pedro, CA
Posts: 42
Thanks: 3
Thanked 10 Times in 5 Posts
well went down, found tdc using a flashlight and watching the piston dwell, marked the pump pulley for zero and a few leading dots- cleaned plugs, backed mixture out 1/2 a turn and she fired up - ran her at 2500 for about 5 minutes and shut her down- all 4 plugs were now tan in color so will see ow she does under load 2moro..
Reply With Quote
  #10   IP: 155.186.124.219
Old 02-07-2020, 10:59 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Curious

CamaroMan, looking back I would like to know if your tach is accurate. Is your engine a "direct drive" or have a reduction unit? Very few A-4's with reduction units see 2500 let alone 3000. Most with reduction units top our around 2500 some a bit higher and direct drives around 2000. Some direct drives with the special Indigo prop will see 2500.

Dave Neptune
Reply With Quote
The Following 3 Users Say Thank You to Dave Neptune For This Useful Post:
Administrator (02-07-2020), ndutton (02-07-2020), sastanley (02-11-2020)
  #11   IP: 24.152.132.140
Old 02-07-2020, 03:51 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
To support Dave's comments, my direct drive with precise timing (set with a light to factory spec) and a smallish 10x8 two blade prop maxes out at 2600 RPM (calibrated tach) in forward gear.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #12   IP: 100.36.65.17
Old 02-09-2020, 01:03 PM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by Dave Neptune View Post
... Very few A-4's with reduction units see 2500 let alone 3000. Most with reduction units top our around 2500 some a bit higher and direct drives around 2000. Some direct drives with the special Indigo prop will see 2500.

Dave Neptune
I guess I’m one of the few.
My A4 with a 2:1 v-drive reduction, and a 3-blade 15x8 prop, gets to 3100 rpm at WOT in a flat calm. (With a clean bottom)
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
possible fuel issue? MN John Fuel System 39 10-02-2016 11:45 AM
possible ignition issue? indigo E.I. MN John Ignition System 4 08-13-2016 05:27 PM
Spring Low Power Issue... J.MILES Pearson 3 03-20-2012 11:11 AM
Just Another Power Loss Issue Bruce A Troubleshooting 33 06-16-2010 02:21 PM
Blowby and Carbon Monoxide? Kurt General Interest 5 06-13-2009 12:17 PM


All times are GMT -4. The time now is 01:42 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved