Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Electrical

Reply
 
Thread Tools Display Modes
  #1   IP: 99.48.145.167
Old 04-29-2020, 03:27 PM
JTG1160 JTG1160 is offline
Senior Member
 
Join Date: Jul 2019
Location: St. Louis
Posts: 34
Thanks: 13
Thanked 6 Times in 2 Posts
Hot Wires

As a new owner of an old A4 motor I recently went through my first spring start up which has gone relatively well. One thing I did notice was the spark plug wires, specifically where they plug on top of the spark plug were of different temps. One was very hot to the touch and another not as much. Does this makes sense or does it indicate some misfiring or other issue? Thx!
Reply With Quote
  #2   IP: 99.255.196.148
Old 04-29-2020, 04:36 PM
Bratina Bratina is offline
Senior Member
 
Join Date: Jun 2015
Location: Toronto, Ontario
Posts: 96
Thanks: 126
Thanked 26 Times in 17 Posts
Quote:
Originally Posted by JTG1160 View Post
As a new owner of an old A4 motor I recently went through my first spring start up which has gone relatively well. One thing I did notice was the spark plug wires, specifically where they plug on top of the spark plug were of different temps. One was very hot to the touch and another not as much. Does this makes sense or does it indicate some misfiring or other issue? Thx!
If you carefully pull a wire off each plug one at a time with the engine running, does the sound of the engine change? I found that I had a defective plug once, which wasn't firing.
Reply With Quote
  #3   IP: 99.48.145.167
Old 04-29-2020, 09:33 PM
JTG1160 JTG1160 is offline
Senior Member
 
Join Date: Jul 2019
Location: St. Louis
Posts: 34
Thanks: 13
Thanked 6 Times in 2 Posts
On the one which seems the coolest the sound of motor doesn't change, on the one which seems the hottest most definitely so I get it that that would indicate a defective plug. On another which was only moderately warm the sound doesn't change which is what drove my original question. Why would one spark plug be hotter than another if both are firing?
Reply With Quote
  #4   IP: 67.169.215.221
Old 04-29-2020, 11:32 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
If you can pull off a spark plug wire and the engine continues to run the same as before, that means that the cylinder is not firing. I would focus there first.

Once you get the engine running properly on all cylinders, then I would go hunting for new challenges. ;^)
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 04-29-2020 at 11:32 PM. Reason: spelling
Reply With Quote
  #5   IP: 72.69.36.126
Old 04-29-2020, 11:56 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
So...you have two plugs that aren’t making a difference once the boot is removed?

Are you sure the boots are on the plugs correctly, and those two boots aren’t switched? The correct order is 1-2-4-3...it says so right on the side of the motor but is easy to forget, and a lot of engines run surprisingly well on fewer than 4 cylinders.

A frequent cause of an unhelpful spark plug: stuck valves. Measure the compression, treat fuel with a double dose of MMO, and try to bump the valves down with an Allen wrench through the plug hole before becoming a head surgeon.
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
ronstory (04-30-2020)
  #6   IP: 47.142.141.4
Old 04-30-2020, 12:37 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by JTG1160 View Post
most definitely so I get it that that would indicate a defective plug. (MAYBE) On another which was only moderately warm the sound doesn't change which is what drove my original question. Why would one spark plug be hotter than another if both are firing?
Maybe no power is getting to one plug and the moderately warm plug is getting power intermittently. Maybe the wiring is shot or there's corrosion in the distributor cap towers.
If you want to test the plugs swap them around and see if the problem follows the plug.

ex TRUE GRIT

Edit: Have a look inside the distributor cap for excessive burning of the rotor and distributor cap contacts.

Last edited by JOHN COOKSON; 04-30-2020 at 01:51 AM.
Reply With Quote
  #7   IP: 155.186.124.219
Old 04-30-2020, 09:47 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Plugs & BOOTS

Sparkplugs have an ideal temp at which they like to run, thus the various heat ranges of plugs. The heat range is governed by what the engine is designed to do so the plug temp easily starts the "burn". If the plug is to cold it is hard to start the burn and if it is to hot it can start the burn before the spark gets there preignition. Also the "boots" on the plugs are part of the design to regulate the cooling rate of the plug and keeping it warm. Boots are important in most applications!!

Now a cold or cooler plug when the engine is running can be 2 things, either the cylinder has a malfunction, like fuel mix, sticky valves or vacuum leaks. If the cylinder is compromised it will not make the power which is the heat thus a cooler plug. The other is the ignition side. If there is a weak spark or a compromised wire that spark can be weak, it will not lite the burn very well and not create much heat (power) and thus a cooler feeling plug.

Dave Neptune
Reply With Quote
The Following 4 Users Say Thank You to Dave Neptune For This Useful Post:
JTG1160 (05-04-2020), ronstory (04-30-2020), Sam (04-30-2020), thatch (04-30-2020)
  #8   IP: 99.30.185.198
Old 04-30-2020, 10:04 AM
thatch thatch is online now
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Coolant flow?

In general, the coolant or waterflow is more active toward the thermostat or water-outlet end of the head. Because of this, it may just be a case of heat transfer to a hotter part of the head. Which plug(s) are running hotter?
Tom
Reply With Quote
The Following 2 Users Say Thank You to thatch For This Useful Post:
Dave Neptune (04-30-2020), Sam (04-30-2020)
  #9   IP: 70.160.39.207
Old 04-30-2020, 10:22 AM
indigo indigo is offline
 
Join Date: Jun 2007
Location: Williamsburg, VA
Posts: 54
Thanks: 8
Thanked 54 Times in 28 Posts
Proper Torque on plugs

A spark plug that is not properly seated will have less heat transfer to or from the head. A poorly seated plug will run hotter than a properly seated plug. An easy check.

Tom
Reply With Quote
  #10   IP: 99.48.145.167
Old 04-30-2020, 02:05 PM
JTG1160 JTG1160 is offline
Senior Member
 
Join Date: Jul 2019
Location: St. Louis
Posts: 34
Thanks: 13
Thanked 6 Times in 2 Posts
Grow thoughts and ideas, thank you everyone and really appreciate it. Hope it's not a sticky valve and maybe just a faulty plug but will check into all of these next weekend when I'm back at the boat and will report back!
Reply With Quote
  #11   IP: 72.69.36.126
Old 05-01-2020, 10:17 AM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Certainly rule out simpler causes, but a sticky valve is not necessarily a disaster. Direct lubrication, a bit of manipulation, fuel treatment, and some exercise can clear up a lot of situations. Valves WANT to work, they sometimes just need a little help.
Reply With Quote
The Following 2 Users Say Thank You to tenders For This Useful Post:
Dave Neptune (05-01-2020), JTG1160 (05-04-2020)
  #12   IP: 99.48.145.167
Old 05-10-2020, 10:25 PM
JTG1160 JTG1160 is offline
Senior Member
 
Join Date: Jul 2019
Location: St. Louis
Posts: 34
Thanks: 13
Thanked 6 Times in 2 Posts
So got down to the boat, pull all the plugs and checked compression and that the valves were moving, all good. Cleaned the plugs and still had the issue with one not firing so put a new plug into that one and now hitting on all 4 cylinders. Thanks for everyone's help and advice. I still need to look inside the distributor cap, is there annual maintenance that is recommended here?
Reply With Quote
The Following User Says Thank You to JTG1160 For This Useful Post:
Administrator (05-11-2020)
Reply

Tags
Spark Plug Wires

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Carbon Fiber plug wires irtrimble Ignition System 9 08-16-2019 04:23 PM
Mystery wires on alternator Jtinius Electrical 25 06-22-2013 01:27 PM
Plug wires Skywalker Troubleshooting 13 05-28-2013 04:36 PM
Always Label the Wires Dave O Ignition System 1 04-08-2008 06:58 AM
Melted Coil Wires RGoeke Ignition System 1 08-19-2007 09:54 PM


All times are GMT -4. The time now is 05:50 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved