#1
IP: 206.47.13.123
|
|||
|
|||
Main jet cover gasket source
Does anyone know of a source for the gasket for the main jet cover? In order to drain the fuel from the card when winterizing, I loosen the main jet cover. However, the gasket is deteriorating, and I would like to have some replacements.
I can buy a main jet cover and gasket from Don, but I only need a gasket. Thanks
__________________
Larry Bradley C&C Corvette 31 "Lady Di" Clark's Marina Gananoque, ON, Canada in the beautiful Thousand Island of the St. Lawrence River |
#2
IP: 71.118.13.238
|
|||
|
|||
Larry, it's a standard fiber type washer available in most Hardware and Parts houses. Just take the old one with you to get the right size.
Dave Neptune |
#3
IP: 206.47.13.123
|
|||
|
|||
Dave, the old washer is toast. I did find a Briggs and Stratton lawnmower washer, but it was very thin, and didn't last long.
I have the carb here at home, so I can actually take it with me to check the fit.
__________________
Larry Bradley C&C Corvette 31 "Lady Di" Clark's Marina Gananoque, ON, Canada in the beautiful Thousand Island of the St. Lawrence River |
#4
IP: 70.27.58.162
|
||||
|
||||
Larry - why don't you just drain the fuel from the float bowl using the drain plug?
|
#5
IP: 206.125.176.3
|
||||
|
||||
lhbradley, I've used a Briggs & Stratton washer (from my push lawnmower) with great success. It looks to be the same quality as the Moyer issued one.
I have the part number at home..will try to remember to post it up here. edit - Elizabeth and I discussed this very subject this past spring...check out this post..B&S # 271716 is the one I am using --> http://www.moyermarine.com/forums/sh...12&postcount=8
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 10-06-2014 at 09:33 AM. |
#6
IP: 206.47.13.123
|
|||
|
|||
Drain plug? My carb doesn't HAVE a drain plug. I was actually thinking about putting one in myself, since the main jet cover is hard to get at.
And yes, the Briggs and Stratton washers are the right size, but are not a thick as the originals. I was thinking of using two at a time.
__________________
Larry Bradley C&C Corvette 31 "Lady Di" Clark's Marina Gananoque, ON, Canada in the beautiful Thousand Island of the St. Lawrence River |
#7
IP: 206.125.176.3
|
||||
|
||||
Larry, apparently some carbs have a separate drain plug on the underside of the float bowl. I have three carbs, and I think only one of them has a drain plug.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
#8
IP: 70.27.58.162
|
||||
|
||||
Quote:
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
thermostat installation with new MMI Gasket.... | jsutphen | Cooling System | 2 | 05-20-2012 05:39 PM |
Water in Cylinders, Blown Head Gasket | edwardc | Troubleshooting | 37 | 10-01-2010 05:13 PM |
Engine will not run below 2000 rpm! | SailorT | Fuel System | 4 | 01-10-2010 11:43 AM |
5 bolt gasket on a 4 bolt carb? | sastanley | Fuel System | 5 | 12-03-2008 01:22 PM |