Forum: For Sale - Engines and Engine Parts
05-09-2021, 09:22 PM
|
Replies: 1
Views: 971
A4 Parts
I have an array of good and usable A4 parts a couple of exhaust manifolds and two different alternators, a couple of carbs, distributor, etc. All for late model A4 - I think I have one or two carbs...
|
Forum: Introductions
09-22-2020, 12:30 AM
|
Replies: 7
Views: 3,911
|
Forum: Introductions
09-11-2020, 01:20 AM
|
Replies: 24
Views: 6,664
|
Forum: Introductions
09-08-2020, 11:45 PM
|
Replies: 24
Views: 6,664
Congratulations on your P30 and hope you enjoy...
Congratulations on your P30 and hope you enjoy it. I've owned mine for over 20 years and have not been able to justify upgrading to another boat. I find she does all I need and is a good sailing...
|
Forum: Polls
09-08-2020, 11:34 PM
|
Replies: 14
Views: 6,174
|
Forum: General Interest
09-03-2020, 04:12 PM
|
Replies: 27
Views: 8,740
|
Forum: Troubleshooting
08-22-2020, 12:55 AM
|
Replies: 4
Views: 1,146
|
Forum: Troubleshooting
08-21-2020, 12:33 PM
|
Replies: 4
Views: 1,146
|
Forum: General Interest
08-20-2020, 09:49 PM
|
Replies: 22
Views: 6,469
|
Forum: General Interest
08-20-2020, 09:46 PM
|
Replies: 22
Views: 6,469
|
Forum: General Interest
08-20-2020, 09:22 PM
|
Replies: 22
Views: 6,469
Neil,
Thanks - Yes I understand the...
Neil,
Thanks - Yes I understand the relationships.
It has been a slow evolutionary process.
I have the battery capacity and the recharging ability via alternator.
I fall short on the solar if...
|
Forum: Troubleshooting
08-20-2020, 09:15 PM
|
Replies: 4
Views: 1,146
Oil Pressure Question
I am finally back in the water since 2018 with a new to me engine and mast...long story which I won't get into.
The engine appears to be a very clean low hour engine and runs perfectly, except for...
|
Forum: General Interest
08-20-2020, 08:55 PM
|
Replies: 22
Views: 6,469
Great thread - thanks
I've been considering a NY to Maine cruise for some time now. Maybe next summer after replacing the engine and mast. I'll post my question about this new to me engine in a different thread.
I...
|
Forum: Drive Train / Propellers
01-02-2020, 02:36 AM
|
Replies: 35
Views: 16,003
DDO - I would try to liberally douse the whole...
DDO - I would try to liberally douse the whole thing w/ PB Blaster several times over a few weeks, not forgetting to tap with a hammer each time. If there is any head left at all on the 3 coupling...
|
Forum: Overhaul
12-27-2019, 09:40 PM
|
Replies: 2
Views: 1,961
|
Forum: Cooling System
12-27-2019, 09:39 PM
|
Replies: 17
Views: 3,665
Don, as well as i can tell the threads in the...
Don, as well as i can tell the threads in the block are okay. My unscientific method was to chase them with a sharp awl to the end and then a tap to clean them out. They seem okay. Thanks for you...
|
Forum: Overhaul
12-27-2019, 07:22 PM
|
Replies: 2
Views: 1,961
Copper tube
I'm about ready to set my engine back on the beds but have a question.
I cannot for the life of me remember where the copper tube - just in front of the carb and behind the flywheel goes. I've...
|
Forum: Cooling System
12-27-2019, 05:17 PM
|
Replies: 17
Views: 3,665
Photos
The stud was from the center of the exhaust manifold.
And just a general picture...about ready to set it on the engine beds
|
Forum: Cooling System
12-26-2019, 10:03 PM
|
Replies: 17
Views: 3,665
|
Forum: Cooling System
12-26-2019, 02:29 AM
|
Replies: 17
Views: 3,665
|
Forum: General Interest
12-18-2019, 06:54 AM
|
Replies: 25
Views: 6,302
|
Forum: General Interest
12-16-2019, 06:11 AM
|
Replies: 136
Views: 63,272
|
Forum: Cooling System
12-09-2019, 09:11 PM
|
Replies: 17
Views: 3,665
Al: Now that I understand it is likely from...
Al: Now that I understand it is likely from corrosion, I think you are right and will seriously consider doing all 3 manifold studs.
The head? I'm not sure I want to venture into it at this time.
I...
|
Forum: Troubleshooting
12-09-2019, 03:27 PM
|
Replies: 25
Views: 5,875
John, for what it is worth, I went thru...
John, for what it is worth, I went thru intermittent flue problems for 2 years.
Constantly cleaning the carb jet, burnt out a fuel pump and then removed the hose from the tank. It was clogged solid...
|
Forum: Cooling System
12-09-2019, 03:12 PM
|
Replies: 17
Views: 3,665
Thanks again Don. I won't be able to get to the...
Thanks again Don. I won't be able to get to the boat till this next Saturday but will follow-up and confirm. This would be very good news indeed.
And UPS just let me know my parts will arrive in the...
|