Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 25 of 132
Search took 0.01 seconds.
Search: Posts Made By: Easy Rider
Forum: Troubleshooting 12-28-2023, 06:45 PM
Replies: 28
Views: 7,236
Posted By Easy Rider
Seems to me the problem could be that your not...

Seems to me the problem could be that your not getting enough water through to the engine when the rev's are up and under load. I would begin by simplifying the set up you have between the through...
Forum: Exhaust System 08-28-2023, 07:34 PM
Replies: 20
Views: 4,272
Posted By Easy Rider
It might not work in other areas but I've found...

It might not work in other areas but I've found by taking the old worn black parts to the plumbing wholesaler they will have gathered all the parts for me in minutes. I do try to not go at busy...
Forum: Troubleshooting 08-22-2023, 04:19 PM
Replies: 35
Views: 3,869
Posted By Easy Rider
Sounds too simple but you might want to go back...

Sounds too simple but you might want to go back and check the new ignition switch wiring.
Forum: Cooling System 08-13-2023, 03:34 PM
Replies: 4
Views: 522
Posted By Easy Rider
I hear your pain. Access to that pump while...

I hear your pain. Access to that pump while attempting to change the impellor without removing the whole pump is a pig of a job on a Ranger 29. You almost have to be standing on your head. Then...
Forum: Troubleshooting 08-04-2023, 06:33 PM
Replies: 4
Views: 806
Posted By Easy Rider
Vicki, Yes welcome to the forum. I'm wondering...

Vicki, Yes welcome to the forum. I'm wondering did you replace the carb or rebuild the carb. There is a difference that might have a bearing here and what was the motor doing before deciding to...
Forum: Troubleshooting 07-24-2023, 07:05 PM
Replies: 3
Views: 490
Posted By Easy Rider
My first thought is that there's some line still...

My first thought is that there's some line still on the shaft that was missed on your dive under. Time for another look perhaps. I've heard that this can sometimes damage the cutless bearing so you...
Forum: Troubleshooting 07-09-2023, 03:41 PM
Replies: 4
Views: 754
Posted By Easy Rider
Me thinks it would be better to install the new,...

Me thinks it would be better to install the new, to be bought pump, and keep the old one for a spare. Not sure if I would even trust the old one as a spare.
Forum: Troubleshooting 07-07-2023, 02:57 PM
Replies: 5
Views: 687
Posted By Easy Rider
Looking at the way the safety wire in the nut has...

Looking at the way the safety wire in the nut has turned to the left and loosened might be an indication that the nut loosened on its own possibly by the keyway slug being too loose to begin with. ...
Forum: Troubleshooting 06-28-2023, 06:15 PM
Replies: 11
Views: 1,069
Posted By Easy Rider
Did you test the ignition/starter button yet?...

Did you test the ignition/starter button yet? Sure sounds like a corroded connection somewhere.
Forum: Troubleshooting 06-26-2023, 08:10 PM
Replies: 11
Views: 1,069
Posted By Easy Rider
You might want to have a look at the start...

You might want to have a look at the start switch/key/button. They are known to corrode. Had the same problem once. Easy to test.
Forum: General Maintenance 06-06-2023, 06:01 PM
Replies: 4
Views: 847
Posted By Easy Rider
Could it be a possibility that the hull shape...

Could it be a possibility that the hull shape changed while the boat was out of the water causing the shaft to be out of alignment. I would think this would be a small chance but it can happen. ...
Forum: Troubleshooting 05-16-2023, 07:58 PM
Replies: 3
Views: 903
Posted By Easy Rider
Usually there is a set screw on the shaft side of...

Usually there is a set screw on the shaft side of the coupler that gets tightened into a dimple on the shaft to stop it from spinning. It's possible that if you had one on your coupler that it has...
Forum: Troubleshooting 05-09-2023, 07:57 PM
Replies: 41
Views: 3,097
Posted By Easy Rider
Confirming what Joe says. My sweet spot for...

Confirming what Joe says. My sweet spot for cruising is around 1750 rpm but could push 2000 for short bursts and that was with a two blade prop
Forum: Cooling System 03-13-2023, 08:11 PM
Replies: 7
Views: 1,683
Posted By Easy Rider
I've pressed seals in by using a socket against...

I've pressed seals in by using a socket against the seal and then pressing them in gently using a vice. This method distributes the pressure equally around the seal. Just one other way.
Forum: Cooling System 01-01-2023, 12:20 AM
Replies: 29
Views: 4,309
Posted By Easy Rider
Re the overheating problem. The first thing I...

Re the overheating problem. The first thing I would do is check the through hull valve to see that it is not plugged. Disconnect the intake hose from the through hull valve and then open it up. You...
Forum: Drive Train / Propellers 12-04-2022, 09:43 PM
Replies: 6
Views: 1,508
Posted By Easy Rider
The bearing in the accessory drive are sometimes...

The bearing in the accessory drive are sometimes known to fail and give off a chattering sound. Might be worth checking out. Sometime just tightening the belt will get rid of the chatter. Not a...
Forum: Troubleshooting 09-20-2022, 11:28 PM
Replies: 12
Views: 2,144
Posted By Easy Rider
It seems to me that you're pump could be just...

It seems to me that you're pump could be just sucking air. You might just need to prime your strainer by making sure it's full and making sure the seal is tight. I've had your situation in the past...
Forum: Troubleshooting 07-19-2022, 12:36 AM
Replies: 13
Views: 2,005
Posted By Easy Rider
I recalled and meant to add that yesterday...

I recalled and meant to add that yesterday removing the basket filter top was significantly more difficult than normal. It (filter) was completely empty of water and felt as if under strong vacuum...
Forum: General Maintenance 04-28-2022, 11:39 PM
Replies: 3
Views: 1,084
Posted By Easy Rider
Canadian Tire in Sarnia says they have it. ...

Canadian Tire in Sarnia says they have it. https://www.canadiantire.ca/en/search-results.html?q=rotella+t+4
Forum: Troubleshooting 11-20-2021, 11:29 PM
Replies: 18
Views: 2,604
Posted By Easy Rider
Red face If it's over heating the first and simplest thing...

If it's over heating the first and simplest thing I would do is remove the fitting at the aft end of the manifold where the water line to the exhaust is connected and confirm that it's not plugged up...
Forum: Cooling System 11-10-2021, 02:30 PM
Replies: 19
Views: 3,309
Posted By Easy Rider
Lots of info regarding this topic on the forum. ...

Lots of info regarding this topic on the forum. I'm sure others will chime in and help figure out what's causing it. What about the possibility of over cranking with the sea cock open? Any...
Forum: Cooling System 11-09-2021, 05:28 PM
Replies: 19
Views: 3,309
Posted By Easy Rider
Are you raw water cooled?

Are you raw water cooled?
Forum: Cooling System 10-18-2021, 04:06 PM
Replies: 9
Views: 3,063
Posted By Easy Rider
Have we had an answer yet to follow the hose?

Have we had an answer yet to follow the hose?
Forum: Troubleshooting 06-27-2021, 06:56 PM
Replies: 9
Views: 3,139
Posted By Easy Rider
Well, I'm no "expert" but what jumps out at me is...

Well, I'm no "expert" but what jumps out at me is the height of the muffler and the injection point. IMHP I would suggest moving the muffler down as low as you can get it and make sure the injection...
Forum: Troubleshooting 06-24-2021, 07:42 PM
Replies: 8
Views: 2,707
Posted By Easy Rider
I totally agree with Tenders. Do the basic stuff...

I totally agree with Tenders. Do the basic stuff first. Make sure the prop and hull are clean - including the very bottom of the keel. Even a few barnacles on a prop will cause what you are...
Showing results 1 to 25 of 132

 
Forum Jump

All times are GMT -4. The time now is 08:32 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved