Forum: General Maintenance
10-05-2011, 04:02 PM
|
Replies: 19
Views: 8,134
|
Forum: General Maintenance
10-02-2011, 04:49 AM
|
Replies: 3
Views: 5,563
The way I get the oil out:
Bought MMI's...
The way I get the oil out:
Bought MMI's sump attachment and permanently mounted it in the "oil drain" location shown in jpian's photo.
Attached a short piece of approved fuel hose and...
|
Forum: Troubleshooting
09-23-2011, 05:12 PM
|
Replies: 5
Views: 2,969
|
Forum: Electrical
09-07-2011, 05:59 AM
|
Replies: 35
Views: 21,883
|
Forum: Polls
09-03-2011, 05:46 AM
|
Replies: 75
Views: 52,507
So the GPS vs sextant debate finally found its...
So the GPS vs sextant debate finally found its way onto the peaceful A4 forums. Although a GPS receiver is not among the poll choices, it probably should be. GPS plays a role in calculating fuel...
|
Forum: Fuel System
09-02-2011, 07:34 PM
|
Replies: 18
Views: 8,042
|
Forum: Fuel System
08-28-2011, 09:29 AM
|
Replies: 16
Views: 24,671
By way of followup: I just bought a valved...
By way of followup: I just bought a valved outboard outboard gasoline pump and hooked two lengths of rubber fuel line to it. Tied one of them to a stick and use that to pump out the tank each autumn...
|
Forum: Electrical
08-12-2011, 04:54 AM
|
Replies: 35
Views: 21,883
|
Forum: Electrical
08-12-2011, 04:20 AM
|
Replies: 35
Views: 21,883
Neil, the switch is here:...
Neil, the switch is here: http://bluesea.com/products/5511e . There are four posts. When turned to "on", the switch makes the two circuits independently (engine and house). When switched to...
|
Forum: Cooling System
08-11-2011, 01:50 PM
|
Replies: 31
Views: 26,840
|
Forum: Electrical
08-11-2011, 06:23 AM
|
Replies: 35
Views: 21,883
|
Forum: Electrical
08-10-2011, 05:44 AM
|
Replies: 35
Views: 21,883
Jim, Neil's advice here is gold-plated. My...
Jim, Neil's advice here is gold-plated. My suggestion is to start drawing a schematic of what you have, beginning at the battery. Then the circuits will become clearer and you can sort out wires that...
|
Forum: Drawings and Schematics
08-08-2011, 04:15 PM
|
Replies: 16
Views: 24,500
|
Forum: Drawings and Schematics
08-08-2011, 05:38 AM
|
Replies: 16
Views: 24,500
Don's wiring guide is brilliant, but many of us...
Don's wiring guide is brilliant, but many of us have made a key change to the old style of running a long hot wire from the alternator to an ammeter in the ignition panel and from there all the way...
|
Forum: Drawings and Schematics
08-08-2011, 05:27 AM
|
Replies: 16
Views: 24,500
Jim, I am not sure I understand your question,...
Jim, I am not sure I understand your question, but it might be easiest to think of current flowing from the positive post of the battery through the red cable to the various engine circuits and then...
|
Forum: Drawings and Schematics
08-07-2011, 04:38 PM
|
Replies: 1
Views: 9,970
|
Forum: Wanted to Buy - Engines and Engine Parts
07-19-2011, 04:53 AM
|
Replies: 8
Views: 4,228
|
Forum: Announcements
07-13-2011, 05:57 AM
|
Replies: 14
Views: 5,047
|
Forum: General Interest
06-25-2011, 04:40 PM
|
Replies: 2
Views: 3,633
Sound of a happy Atomic 4
Cold, drizzly, blowy day today: good one for an oil change and other maintenance. While waiting for the engine to warm up, I took this cellphone video. Light coming in the hatch in front of the...
|
Forum: Exhaust System
06-15-2011, 11:38 AM
|
Replies: 19
Views: 8,842
|
Forum: Cooling System
05-19-2011, 05:18 AM
|
Replies: 11
Views: 11,397
|
Forum: Cooling System
05-03-2011, 05:15 AM
|
Replies: 2
Views: 2,878
|
Forum: General Maintenance
04-21-2011, 04:18 AM
|
Replies: 8
Views: 5,304
Don Moyer FAQ: "Based on the original design...
Don Moyer FAQ: "Based on the original design compression ratio of 6.3 to 1, the compression would be 95 PSI. In fact, original test data recorded compression values very close to this value. However,...
|
Forum: Exhaust System
04-21-2011, 04:16 AM
|
Replies: 48
Views: 25,120
I was a little uneasy about that hose too. Will...
I was a little uneasy about that hose too. Will it tolerate the heat? A section of hose connecting hot stack to waterlift muffler reduces engine vibration problems at that joint, but I imagine the...
|
Forum: General Maintenance
04-21-2011, 04:10 AM
|
Replies: 33
Views: 9,034
|