Forum: Fuel System
11-29-2017, 09:16 PM
|
Replies: 22
Views: 4,720
|
Forum: Fuel System
11-29-2017, 09:08 PM
|
Replies: 22
Views: 4,720
I think you're starving for gas, not flooded. I...
I think you're starving for gas, not flooded. I messed with the adjustment screw a little. I think it just makes the engine run hotter and burn more fuel. I couldn't even get a flame to shoot out,...
|
Forum: Troubleshooting
10-13-2017, 06:16 PM
|
Replies: 21
Views: 4,514
|
Forum: Fuel System
08-03-2017, 02:05 PM
|
Replies: 26
Views: 8,167
|
Forum: Fuel System
08-03-2017, 12:47 PM
|
Replies: 26
Views: 8,167
|
Forum: Troubleshooting
08-03-2017, 12:37 PM
|
Replies: 13
Views: 6,105
|
Forum: Troubleshooting
08-01-2017, 12:30 PM
|
Replies: 13
Views: 6,105
|
Forum: General Interest
07-28-2017, 06:48 AM
|
Replies: 17
Views: 4,412
|
Forum: Ignition System
07-27-2017, 12:23 PM
|
Replies: 7
Views: 4,359
|
Forum: Exhaust System
07-18-2017, 08:28 PM
|
Replies: 38
Views: 7,426
|
Forum: Wanted to Buy - Engines and Engine Parts
07-05-2017, 02:20 PM
|
Replies: 8
Views: 7,437
I'm restoring a 64 but, I kinda keep all the...
I'm restoring a 64 but, I kinda keep all the inside work reserved for the winter. I've got quite a bit of time into it. Basically all cosmetic but, stripping paint and grinding rust is still a lot of...
|
Forum: Wanted to Buy - Engines and Engine Parts
07-04-2017, 06:48 AM
|
Replies: 8
Views: 7,437
|
Forum: Electrical
07-03-2017, 08:46 PM
|
Replies: 7
Views: 6,170
The picture is a little hard to see but I think...
The picture is a little hard to see but I think the buzzing is a bad connection with the alligator clips. try sending close ups of each part. Are the clips from a charger or a jury rigged terminal...
|
Forum: Wanted to Buy - Engines and Engine Parts
07-02-2017, 01:14 PM
|
Replies: 8
Views: 7,437
|
Forum: Wanted to Buy - Engines and Engine Parts
06-30-2017, 06:18 PM
|
Replies: 8
Views: 7,437
|
Forum: Drive Train / Propellers
06-04-2017, 10:50 AM
|
Replies: 8
Views: 4,373
|
Forum: Electrical
06-04-2017, 10:37 AM
|
Replies: 22
Views: 4,997
|
Forum: Introductions
06-01-2017, 04:18 PM
|
Replies: 49
Views: 20,348
|
Forum: General Interest
06-01-2017, 03:52 PM
|
Replies: 9
Views: 5,068
Al is 100% correct. Also, you will tear out the...
Al is 100% correct. Also, you will tear out the bottom end. You must have the full 1/16. The compression ratio would be way too high. However, if you replaced all the rod and main bearings and rings...
|
Forum: Introductions
06-01-2017, 03:05 PM
|
Replies: 49
Views: 20,348
|
Forum: Overhaul
05-30-2017, 10:18 PM
|
Replies: 27
Views: 9,069
I think the lifter might be bad at this point,...
I think the lifter might be bad at this point, there is supposed to be a layer of oil in between, not stuck. Also, did the other keepers and washers look gouged up like that one? It kinda looks like...
|
Forum: Introductions
05-30-2017, 09:56 PM
|
Replies: 10
Views: 6,900
|
Forum: Introductions
05-30-2017, 09:51 PM
|
Replies: 10
Views: 6,900
|
Forum: Troubleshooting
05-30-2017, 05:49 PM
|
Replies: 13
Views: 9,467
|
Forum: Introductions
05-29-2017, 08:32 PM
|
Replies: 49
Views: 20,348
|