Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums
Register FAQ Community Today's Posts Search

Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: Davis Modlin
Forum: Ignition System 10-01-2005, 01:32 PM
Replies: 5
Views: 5,720
Posted By Davis Modlin
I don't know if this has been mentioned before or...

I don't know if this has been mentioned before or not, But make sure that you use an INTERNAL resistor coil NOT an EXTERNAL resistor. If you use an external resistor the coil will over heat and...
Forum: General Interest 09-21-2005, 07:50 PM
Replies: 1
Views: 3,887
Posted By Davis Modlin
The way I look at it is, Why put any extra wear...

The way I look at it is, Why put any extra wear on the cutless bearing if you don't have too.

Pat
E29
Holy Guacamole
DMA4
Forum: General Interest 06-08-2005, 08:52 PM
Replies: 3
Views: 5,536
Posted By Davis Modlin
Talking The main reason that I used my old engine mounts...

The main reason that I used my old engine mounts was to give the engine some stability while transporting it to and from the boat. The engine tended to roll around in the bed of my truck (even thou...
Forum: General Interest 06-07-2005, 01:50 PM
Replies: 3
Views: 5,536
Posted By Davis Modlin
When I rebuilt my A4, I just took my old engine...

When I rebuilt my A4, I just took my old engine mounts and put them onto a couple of 4x6 pieces of wood. this allowed me to slide the engine around without it sitting on the oilpan.

Pat
DMA4
Forum: Fuel System 03-13-2005, 12:41 PM
Replies: 6
Views: 7,976
Posted By Davis Modlin
Exclamation Flame Arrestor

The Flame restrictor works by simply restricting or "choking off" the path by which the flame would travel. In other words the air going into the carb is moving at a slow and even pace, But when the...
Forum: Fuel System 03-12-2005, 01:43 PM
Replies: 6
Views: 7,976
Posted By Davis Modlin
Hello Jim First: Where do you live? on the...

Hello Jim

First: Where do you live? on the left, the right, or in the groove. Also, Did the machanic adjust the carb only or did he adjust the timming aswell? If he adjusted the timming, Just set...
Forum: Troubleshooting 02-06-2005, 02:28 PM
Replies: 5
Views: 10,889
Posted By Davis Modlin
I had somewhat the same problem when I bought my...

I had somewhat the same problem when I bought my ericson 29 a few years back. I would go out for a while and it would shut down, I would drop anchor or would pull up to an empty end tie, Pull the...
Forum: General Maintenance 02-03-2005, 06:44 PM
Replies: 45
Views: 23,534
Posted By Davis Modlin
In the rebuild that I'm finishing right now, I...

In the rebuild that I'm finishing right now, I removed the head and then the studs

Davis
Forum: General Interest 01-20-2005, 02:24 PM
Replies: 8
Views: 11,946
Posted By Davis Modlin
I was reading this thread and could help but...

I was reading this thread and could help but wonder that if the sensor not being in the direct flow of the water. the bulk of the water may be flowing right past the T fitting and not into it thus...
Forum: Overhaul 12-10-2004, 01:55 PM
Replies: 4
Views: 6,979
Posted By Davis Modlin
I just had my block and everything else hot...

I just had my block and everything else hot tanked, And as soon as I recieve the remainder of my parts I will start reassembling my engine. As for the paint on the inside of the block I don't think I...
Forum: General Interest 10-17-2004, 02:54 PM
Replies: 8
Views: 19,930
Posted By Davis Modlin
Rebuild vs Repower

I am in the process of rebuilding my A4 at this time. I had to have my bottom repainted, So before I took her over to the boatyard I disconnected everything from the engine and had vessel assist tow...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 12:38 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved