Forum: Announcements
03-01-2011, 01:29 PM
|
Replies: 64
Views: 64,132
Lat 64 (Russ),
I agree this forum is social...
Lat 64 (Russ),
I agree this forum is social networking and some social networking has it's place in appropriate communication instances. This forum is actually a great example of appropriate use of...
|
Forum: Announcements
03-01-2011, 11:56 AM
|
Replies: 64
Views: 64,132
I believe "Social Networking" term is an...
I believe "Social Networking" term is an oxymoron. Like Military and Intelligence!
Social networking isolates more than connects. We lose valuable face to face social skills while typing behind...
|
Forum: Pearson
02-24-2011, 01:13 AM
|
Replies: 41
Views: 28,244
|
Forum: Pearson
02-24-2011, 12:53 AM
|
Replies: 41
Views: 28,244
I agree. :o As a matter of fact while the...
I agree. :o As a matter of fact while the engine is out I plan to put all of the wires in looms and add a batt negative buss to place all of the common heavy guage wires onto so I only have one...
|
Forum: Pearson
02-23-2011, 11:36 PM
|
Replies: 41
Views: 28,244
|
Forum: Pearson
02-23-2011, 12:45 PM
|
Replies: 41
Views: 28,244
Engine is finally out!!!
Well I've finally got the engine removed. With several ideas floating around on this and other websites, with the help of a fork lift, a long stinger, and a six foot long pipe to act as a fulcrum -...
|
Forum: Pearson
02-02-2011, 06:18 PM
|
Replies: 41
Views: 28,244
|
Forum: Pearson
02-02-2011, 06:16 PM
|
Replies: 41
Views: 28,244
Bill,
It's not sanitation hose - it's a super...
Bill,
It's not sanitation hose - it's a super heavy duty water supply hose used for floating homes. It's clear so one can see the water line, and bursting psi is about 160. A real PIA to work...
|
Forum: Pearson
02-02-2011, 02:22 PM
|
Replies: 41
Views: 28,244
As promised pictures...
http://www.moyermarine.com/forums/picture.php?albumid=65&pictureid=762
The engine compartment at the beginning - NOTICE THE CAN of PB in lower right corner!!!
...
|
Forum: Pearson
02-02-2011, 10:46 AM
|
Replies: 41
Views: 28,244
Update
Well folks,
After a bout with pneumonia over the winter, I'm in the process of pulling the engine. I took compression numbers and here is what I have:
Cyl# Dry Wet
1 - 112 - 140
2 - ...
|
Forum: General Interest
02-02-2011, 10:14 AM
|
Replies: 8
Views: 3,134
|
Forum: Fuel System
11-28-2010, 10:17 PM
|
Replies: 29
Views: 10,289
I wonder if the distributor was installed...
I wonder if the distributor was installed incorrectly. Also electronic ignition systems usually have almost a full dwell angle, so for a four cylinder the dwell angle could be as high as 90 degrees...
|
Forum: Safety
11-22-2010, 03:08 AM
|
Replies: 47
Views: 57,656
|
Forum: General Interest
11-15-2010, 12:34 AM
|
Replies: 19
Views: 4,130
I've switched to LED lights...
I've gone the LED route and have been very pleased with the results both in lighting and color temperature. I have five one foot LED strips and the cabin is light up quite nicely. They cost $20 for...
|
Forum: Exhaust System
11-14-2010, 05:11 PM
|
Replies: 6
Views: 4,379
Good question Mike.
Can you see if there is...
Good question Mike.
Can you see if there is enough surface area left on the manifold for the flange to seal against? If so doubling up the flange gasket may help, but my guess is you maybe in need...
|
Forum: Pearson
11-14-2010, 05:02 PM
|
Replies: 41
Views: 28,244
update on reduction gear install...
Greetings folks,
Well I found a used reduction gear. It came with the reversing gear and aft housing (early model). Also picked up a used starter for a spare.
I've been re-evaluating the...
|
Forum: Pearson
11-11-2010, 11:30 PM
|
Replies: 41
Views: 28,244
Posting a Picture...
Hanley,
The P35 is located in Anacortes WA, I'm in Portland OR. It will be about a three to four weeks before I travel back up to Anacortes. I'll be sure to get pictures then and post them here.
...
|
Forum: Pearson
11-11-2010, 01:25 PM
|
Replies: 41
Views: 28,244
Thanks folks,
For the Replies. I need to add...
Thanks folks,
For the Replies. I need to add some additional information to make the picture clearer.
First, I changed the existing prop to 11 x 5 RH. This allowed the A4 to reach 2450 rpm. :) ...
|
Forum: Pearson
11-11-2010, 12:40 AM
|
Replies: 41
Views: 28,244
Pearson 35 Upgrading to 2 to 1 reduction
Hey folks,
I have a P35 with the A4 and it's beginning to show it's age a little. I've given a lot of thought to re-powering with the Beta 28 but the price tag is around 9K with me doing all the...
|
Forum: Pearson
10-24-2010, 08:50 PM
|
Replies: 10
Views: 14,515
|
Forum: Polls
08-11-2010, 01:19 PM
|
Replies: 102
Views: 86,955
|
Forum: Polls
08-10-2010, 08:28 PM
|
Replies: 102
Views: 86,955
Where does one find "SG" grade oil?
...
Where does one find "SG" grade oil?
Everything I've found is rated at SL or SM.
According to the summer newsletter, anything greater than SG is "too slippery" for our wet clutches. Currently...
|
Forum: Announcements
08-02-2010, 01:47 AM
|
Replies: 5
Views: 2,589
|
Forum: For Sale - Engines and Engine Parts
08-02-2010, 01:26 AM
|
Replies: 5
Views: 2,974
|
Forum: General Maintenance
08-02-2010, 01:22 AM
|
Replies: 33
Views: 9,880
Well folks,
I installed the Indigo oil filter...
Well folks,
I installed the Indigo oil filter and 29 hrs after the first oil change, the oil is almost as clean as when I did the oil change. I adjusted the oil pressure for 15 - 20 at 1000 rpm an...
|