Forum: Introductions
10-22-2021, 10:10 PM
|
Replies: 7
Views: 3,915
Welcome....
Please come here for Atomic Four...
Welcome....
Please come here for Atomic Four advice exclusively. The other forums are full of know-it-alls who dispense BS. Here any BS gets checked and appropriately corrected.
Buy from Moyer....
|
Forum: General Interest
04-13-2021, 01:02 AM
|
Replies: 17
Views: 3,247
|
Forum: Polls
02-20-2021, 01:26 AM
|
Replies: 6
Views: 4,450
|
Forum: Overhaul
02-03-2021, 09:27 PM
|
Replies: 152
Views: 58,570
|
Forum: Troubleshooting
01-22-2021, 09:50 PM
|
Replies: 70
Views: 9,502
That insulation I have pictured does not have...
That insulation I have pictured does not have foil backing. It is just woven fiberglass. (I think 2 inches wide) It stays together pretty well. After 10 years the exhaust failed and I made a new one....
|
Forum: Troubleshooting
01-21-2021, 09:13 PM
|
Replies: 12
Views: 2,706
|
Forum: Troubleshooting
01-21-2021, 09:04 PM
|
Replies: 70
Views: 9,502
|
Forum: Cooling System
01-12-2021, 03:12 PM
|
Replies: 3
Views: 2,006
|
Forum: General Interest
10-12-2020, 12:11 AM
|
Replies: 23
Views: 4,987
|
Forum: Fuel System
10-09-2020, 09:36 PM
|
Replies: 23
Views: 3,631
|
Forum: Fuel System
08-30-2020, 05:01 PM
|
Replies: 6
Views: 2,237
|
Forum: Fuel System
08-27-2020, 11:26 PM
|
Replies: 21
Views: 3,343
take the carb drain plug out.
Find out what...
take the carb drain plug out.
Find out what size pipe fits in the hole. I am guessing it is 1/8 pipe. Get a pipe nipple this size. get a clear hose the will fit over this nipple. Screw the nipple...
|
Forum: General Interest
08-07-2020, 10:16 PM
|
Replies: 167
Views: 45,316
When I got my boat it had a groco strainer like...
When I got my boat it had a groco strainer like Neal pictured above. The hose barbs (1/2 inch NPT) were made to accept either 5/8 ID or 1/2 ID hose. The ID of the barb just fits a 1/4 inch drill bit....
|
Forum: Ignition System
08-07-2020, 09:44 PM
|
Replies: 19
Views: 4,066
|
Forum: General Interest
07-30-2020, 07:32 PM
|
Replies: 16
Views: 3,765
|
Forum: Reversing Gear
06-22-2020, 03:18 PM
|
Replies: 3
Views: 1,582
|
Forum: Cooling System
06-21-2020, 04:58 PM
|
Replies: 21
Views: 4,382
I ran the engine using the washdown hose as a...
I ran the engine using the washdown hose as a source of seawater just to see if it would work. it did.
Can also us the washdown hose to shoot thru the thru hull and try to clear the obstruction.
...
|
Forum: General Interest
06-10-2020, 09:42 PM
|
Replies: 14
Views: 4,013
|
Forum: Troubleshooting
05-02-2020, 02:15 AM
|
Replies: 4
Views: 2,002
|
Forum: General Interest
04-14-2020, 08:46 PM
|
Replies: 21
Views: 5,099
what do we have here?
A year ago I took a tour of the SS American Victory berthed in Tampa. She is a museum now.
There was this engine just sitting there, all alone and no sign.
Should be pictures below.
|
Forum: General Maintenance
01-31-2020, 04:48 PM
|
Replies: 27
Views: 5,363
|
Forum: Drive Train / Propellers
01-27-2020, 03:21 PM
|
Replies: 6
Views: 4,191
|
Forum: Troubleshooting
10-12-2019, 01:43 AM
|
Replies: 9
Views: 3,395
The cutless bearing is easy to get out on the...
The cutless bearing is easy to get out on the T34. On mine there are 2 set screws holding it in. I use a threaded rod and an approximately 1 1/8 socket to pull the cutless.
I often pull the shaft...
|
Forum: Tartan
06-08-2019, 06:12 AM
|
Replies: 5
Views: 6,329
|
Forum: Troubleshooting
05-23-2019, 08:59 PM
|
Replies: 8
Views: 2,872
|