Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: romantic comedy
Forum: Exhaust System 03-05-2021, 05:41 PM
Replies: 0
Views: 1,097
Posted By Al Schober
1 1/4 tap

Came across the 1 1/4" pipe tap in my browsing. Thought someone might need one.
https://newlondon.craigslist.org/tls/d/westerly-pipe-thread-tap/7270723993.html
Forum: Announcements 11-26-2020, 10:40 AM
Replies: 22
Views: 3,557
Posted By Dave Neptune
Most all valves in the past set right down on the...

Most all valves in the past set right down on the cast iron. The seats are replaceable by boring and pressing in a hardened metal seat like on aluminum heads. Once the lead was being eliminated the...
Forum: Exhaust System 10-24-2020, 08:51 AM
Replies: 13
Views: 5,786
Posted By edwardc
Yes, I used the cloth/fiberglass wrap that MMI...

Yes, I used the cloth/fiberglass wrap that MMI sells. It is held in place with some thin stainless straps.


As for Sch 40 vs 80, I used sch 40. I had some worry at first, but the results have...
Forum: Reversing Gear 09-22-2020, 10:45 PM
Replies: 7
Views: 2,164
Posted By Al Schober
Those fingers have to ride in the groove. Make...

Those fingers have to ride in the groove. Make sure your shift linkage gets you there. If it doesn't, fix the shift linkage.
Forum: Reversing Gear 09-22-2020, 07:17 PM
Replies: 7
Views: 2,164
Posted By Dave Neptune
Looks like the adjustment is to tight. The pawls...

Looks like the adjustment is to tight. The pawls should ride in the "detent grove" which holds the trans in forward.

If you shift with the lever on the trans do the pawls ride in the detent?
...
Forum: Helpful Videos 03-21-2020, 10:06 AM
Replies: 1
Views: 10,183
Posted By Administrator
Atomic 4 - Ignition Timing

From our new YouTube channel (https://www.youtube.com/channel/UC8G5eWR1ieTOSSLXZhCBdJg):

2ysFGcm8oNo
Forum: Cooling System 07-31-2019, 06:22 PM
Replies: 6
Views: 3,592
Posted By ndutton
In time you'll realize, as the rest of us already...

In time you'll realize, as the rest of us already have, that MMI products are carefully thought out, of the highest standards and deliver lasting value for the cost. Until then, please consider that...
Forum: Overhaul 12-12-2018, 07:02 AM
Replies: 18
Views: 6,830
Posted By southcoasting
Angry Just to update everyone, I had dropped off bottom...

Just to update everyone, I had dropped off bottom end block for rest of teardown and inspection/measuring. Long story short, my main problem with the compression on one piston was the valve. Also,...
Forum: Ignition System 02-18-2018, 09:56 AM
Replies: 57
Views: 15,543
Posted By Oldlaxer1
To further the discussion...

Received this from Indigo:

Thank you for purchasing an Indigo Electronics Ignition Kit for your Atomic 4. Over the years we have learned a tremendous amount about the operating...
Forum: Fuel System 11-22-2015, 01:24 PM
Replies: 29
Views: 12,999
Posted By Dave Neptune
Lightbulb Neil, what you are referring to "bowl vent" is to...

Neil, what you are referring to "bowl vent" is to keep the "float bowl" at the same ambient pressure as the carb throat in the Zenith. This vent keeps the pressure constant and maintains the float...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 11:07 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved