Forum: Troubleshooting
11-13-2020, 08:32 PM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
11-13-2020, 08:53 AM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
10-15-2020, 12:24 PM
|
Replies: 12
Views: 2,775
|
Forum: Troubleshooting
09-26-2020, 04:23 PM
|
Replies: 5
Views: 1,616
To make it easier to get the engine out of the...
To make it easier to get the engine out of the boat, I mounted it on an engine stand in the boat and then removed everything from the block. I don't recall the exact order of disassembly, but I do...
|
Forum: Troubleshooting
07-11-2018, 10:23 AM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
07-09-2018, 07:03 PM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
07-04-2018, 04:25 PM
|
Replies: 78
Views: 20,836
I took a couple of pics today.
As Neil points...
I took a couple of pics today.
As Neil points out, that hole doesn't get a plug or bolt.
It's open and dry.
As we've already pointed out, the drain plug is on the Starter/Alt side and forward. ...
|
Forum: Troubleshooting
07-03-2018, 07:55 AM
|
Replies: 78
Views: 20,836
The hole you circled, the center one at the...
The hole you circled, the center one at the bottom of the pan, is intended to remain open. It does not have anything to do with the wet oil area of the pan but is instead a path for errant liquids...
|
Forum: Troubleshooting
07-03-2018, 06:40 AM
|
Replies: 78
Views: 20,836
Image below. Also, look here...
Image below. Also, look here (https://moyermarine.com/product/latest-style-flywheel-housing-used-ocas_02-3_310/) and here (https://moyermarine.com/product/flywheel-housing-gasket-gask_12_151/).
...
|
Forum: Troubleshooting
07-01-2018, 11:09 PM
|
Replies: 78
Views: 20,836
engine pull
If you do need to pull the A4, be absolutely sure the output coupling is completely disengaged from the shaft before lifting! For me, a bent shaft was quite expensive and time-consuming to replace.
|
Forum: Troubleshooting
07-01-2018, 08:11 PM
|
Replies: 78
Views: 20,836
Just my opinion
If it's the plug, the engine needs to come out of its hole to replace. If it's not the plug, all other possibilities that result in losing all oil with the engine at rest involve the pan which also...
|
Forum: Troubleshooting
07-01-2018, 07:44 PM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
07-01-2018, 06:08 PM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
06-26-2018, 10:33 AM
|
Replies: 78
Views: 20,836
Some A4s had a factory oil removal pump. Maybe...
Some A4s had a factory oil removal pump. Maybe yours? Or perhaps an aftermarket pump was installed? Perhaps that fitting corroded, or loosened, or a hose coming out of it failed, etc.
Hard to tell...
|
Forum: Troubleshooting
06-26-2018, 10:05 AM
|
Replies: 78
Views: 20,836
|
Forum: Introductions
06-26-2018, 09:59 AM
|
Replies: 5
Views: 4,178
|
Forum: Troubleshooting
06-26-2018, 09:57 AM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
06-26-2018, 12:27 AM
|
Replies: 78
Views: 20,836
|
Forum: Troubleshooting
06-25-2018, 05:46 PM
|
Replies: 78
Views: 20,836
2 cents
Pull the engine and get another base pan. Should be lots of them around as neglect killed many old A4's. I'd talk to South Shore Yacht's there in Ontario as they might have one around, or give you...
|
Forum: Troubleshooting
06-25-2018, 04:42 PM
|
Replies: 78
Views: 20,836
|
Forum: Overhaul
03-23-2018, 06:48 AM
|
Replies: 26
Views: 5,798
The Dyer Glamour Girl was usually equipped with...
The Dyer Glamour Girl was usually equipped with an A4 as new. The blue boat came up when I did a search, but she does not look totally identical to the one below. She also doesn't really look like a...
|
Forum: Cooling System
01-15-2013, 08:55 AM
|
Replies: 56
Views: 11,997
Thanx & caution
Thanx Jierry, I couldn't find them, I'm no techie :confused: I'm a mechanic & tool maker.
Bill :eek:, that "funky blue hose" is the expensive Goodyear "silicone" double wall really good stuff....
|
Forum: Overhaul
11-03-2011, 08:58 AM
|
Replies: 60
Views: 14,490
My inner carpenter got impatient last night and...
My inner carpenter got impatient last night and started tapping the pipe wrench (on front pulley hub) with a 16 oz. hammer; he then upgraded to a small sledge. Low and behold all of the pistons moved...
|